Chuck Burgess dc12205bb8 Narrowing Belt Gap R ... ### Description The belt gap R is a little too wide allowing the belt to slip off of the carriage part. ### Proposed Changes - change the cube on the bottom of the belt gap increasing the Y from 7.5 to 8 to make the belt gap more narrow (1.95mm gap)		2018-01-05 20:09:56 -07:00
..
Einsy-base.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
Einsy-doors.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
Einsy-hinges.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
LCD-cover-ORIGINAL-MK3.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
bearing.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
cable-holder.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
extruder-body.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
extruder-cover.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
extruder-idler-plug.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
extruder-idler.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
filament-sensor-cover.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
heatbed-cable-cover.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
lcd-supports.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
nozzle-fan.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
polyholes.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
x-carriage-back.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
x-carriage.scad	Narrowing Belt Gap R	2018-01-05 20:09:56 -07:00
x-end-idler.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
x-end-motor.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
x-end.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
y-belt-holder.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
y-belt-idler.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
y-holder-front.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
y-holder-rear.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
y-motor-holder.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
z-axis-bottom.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
z-axis-top.scad	MK3 - initial	2017-11-29 17:24:03 +01:00
z-screw-cover.scad	MK3 - initial	2017-11-29 17:24:03 +01:00