diff --git a/Firmware/Marlin.h b/Firmware/Marlin.h
index 5767b8b21..db1db3e4f 100644
--- a/Firmware/Marlin.h
+++ b/Firmware/Marlin.h
@@ -347,6 +347,9 @@ extern bool sortAlpha;
 
 extern char dir_names[3][9];
 
+// save/restore printing
+extern bool saved_printing;
+
 extern void calculate_extruder_multipliers();
 
 // Similar to the default Arduino delay function, 
diff --git a/Firmware/Marlin_main.cpp b/Firmware/Marlin_main.cpp
index bb6e838fc..1229e10ad 100644
--- a/Firmware/Marlin_main.cpp
+++ b/Firmware/Marlin_main.cpp
@@ -425,6 +425,10 @@ bool no_response = false;
 uint8_t important_status;
 uint8_t saved_filament_type;
 
+// save/restore printing
+bool saved_printing = false;
+
+
 //===========================================================================
 //=============================Private Variables=============================
 //===========================================================================
@@ -477,6 +481,14 @@ unsigned long chdkHigh = 0;
 boolean chdkActive = false;
 #endif
 
+// save/restore printing
+static uint32_t saved_sdpos = 0;
+static float saved_pos[4] = { 0, 0, 0, 0 };
+// Feedrate hopefully derived from an active block of the planner at the time the print has been canceled, in mm/min.
+static float saved_feedrate2 = 0;
+static uint8_t saved_active_extruder = 0;
+static bool saved_extruder_under_pressure = false;
+
 //===========================================================================
 //=============================Routines======================================
 //===========================================================================
@@ -7160,7 +7172,7 @@ static void handleSafetyTimer()
 #error Implemented only for one extruder.
 #endif //(EXTRUDERS > 1)
     static Timer safetyTimer;
-    if (IS_SD_PRINTING || is_usb_printing || isPrintPaused || (custom_message_type == 4)
+    if (IS_SD_PRINTING || is_usb_printing || isPrintPaused || (custom_message_type == 4) || saved_printing
         || (lcd_commands_type == LCD_COMMAND_V2_CAL) || (!degTargetBed() && !degTargetHotend(0)))
     {
         safetyTimer.stop();
@@ -7169,7 +7181,7 @@ static void handleSafetyTimer()
     {
         safetyTimer.start();
     }
-    else if (safetyTimer.expired(1800000ul))
+    else if (safetyTimer.expired(1800000ul)) //30 min
     {
         setTargetBed(0);
         setTargetHotend(0, 0);
@@ -8421,17 +8433,7 @@ void restore_print_from_eeprom() {
 
 
 ////////////////////////////////////////////////////////////////////////////////
-// new save/restore printing
-
-//extern uint32_t sdpos_atomic;
-
-bool saved_printing = false;
-uint32_t saved_sdpos = 0;
-float saved_pos[4] = {0, 0, 0, 0};
-// Feedrate hopefully derived from an active block of the planner at the time the print has been canceled, in mm/min.
-float saved_feedrate2 = 0;
-uint8_t saved_active_extruder = 0;
-bool saved_extruder_under_pressure = false;
+// save/restore printing
 
 void stop_and_save_print_to_ram(float z_move, float e_move)
 {
diff --git a/Firmware/cardreader.cpp b/Firmware/cardreader.cpp
index ace2a9ab5..6371339ad 100644
--- a/Firmware/cardreader.cpp
+++ b/Firmware/cardreader.cpp
@@ -523,7 +523,10 @@ void CardReader::getStatus()
     SERIAL_PROTOCOL(itostr2(time%60));
     SERIAL_PROTOCOLPGM("\n");
   }
-  else{
+  else if (saved_printing) {
+	  SERIAL_PROTOCOLLNPGM("Print saved");
+  }
+  else {
     SERIAL_PROTOCOLLNPGM("Not SD printing");
   }
 }
diff --git a/Firmware/ultralcd.cpp b/Firmware/ultralcd.cpp
index 1df42a861..596c06b43 100644
--- a/Firmware/ultralcd.cpp
+++ b/Firmware/ultralcd.cpp
@@ -5651,8 +5651,6 @@ void lcd_confirm_print()
 
 }
 
-extern bool saved_printing;
-
 static void lcd_main_menu()
 {