LCD menu
- Hide menus during recovering - Un-/Load filament with FSensor active only show Load OR Unload depending on FS sate - Host - Reprint only shown when M79 timer is active - Resume only shown when M79 timer active - Stop print always shown when printing, paused and recovering
This commit is contained in:
3d-gussner
parent
a04063f966
commit
9f8115639a
|
|
@ -5238,53 +5238,66 @@ static void lcd_main_menu()
|
|||
#endif //TMC2130_DEBUG
|
||||
|
||||
// Menu item for reprint
|
||||
if(!printer_active() && !printer_recovering() && (heating_status == HeatingStatus::NO_HEATING)) {
|
||||
if ((GetPrinterState() == PrinterState::SDPrintingFinished) && card.mounted) {
|
||||
if (!printer_active()
|
||||
&& !printer_recovering()
|
||||
&& (heating_status == HeatingStatus::NO_HEATING)) {
|
||||
if ((GetPrinterState() == PrinterState::SDPrintingFinished)
|
||||
&& card.mounted) {
|
||||
MENU_ITEM_FUNCTION_P(_T(MSG_REPRINT), lcd_reprint_from_eeprom);
|
||||
} else if ((GetPrinterState() == PrinterState::HostPrintingFinished) && M79_timer_get_status()) {
|
||||
} else if ((GetPrinterState() == PrinterState::HostPrintingFinished)
|
||||
&& M79_timer_get_status()) {
|
||||
MENU_ITEM_FUNCTION_P(_T(MSG_REPRINT), lcd_send_action_start);
|
||||
}
|
||||
}
|
||||
|
||||
// Menu is never shown when idle
|
||||
if (babystep_allowed_strict() && (printJobOngoing() || lcd_commands_type == LcdCommands::Layer1Cal))
|
||||
if (babystep_allowed_strict()
|
||||
&& (printJobOngoing()
|
||||
|| lcd_commands_type == LcdCommands::Layer1Cal))
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_BABYSTEP_Z), lcd_babystep_z);//8
|
||||
|
||||
if (farm_mode)
|
||||
MENU_ITEM_FUNCTION_P(_T(MSG_FILAMENTCHANGE), lcd_colorprint_change);//8
|
||||
|
||||
if ( moves_planned() || printer_active() ) {
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_TUNE), lcd_tune_menu);
|
||||
} else if (!Stopped) {
|
||||
MENU_ITEM_SUBMENU_P(_i("Preheat"), lcd_preheat_menu);////MSG_PREHEAT c=18
|
||||
if (M79_timer_get_status()) {
|
||||
if(GetPrinterState() == PrinterState::IsReady) {
|
||||
MENU_ITEM_FUNCTION_P(_T(MSG_SET_NOT_READY), lcd_printer_ready_state_toggle);
|
||||
} else {
|
||||
MENU_ITEM_FUNCTION_P(_T(MSG_SET_READY), lcd_printer_ready_state_toggle);
|
||||
if (!printer_recovering()) {
|
||||
if ( moves_planned()
|
||||
|| printer_active()) {
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_TUNE), lcd_tune_menu);
|
||||
} else if (!Stopped) {
|
||||
MENU_ITEM_SUBMENU_P(_i("Preheat"), lcd_preheat_menu);////MSG_PREHEAT c=18
|
||||
if (M79_timer_get_status()) {
|
||||
if(GetPrinterState() == PrinterState::IsReady) {
|
||||
MENU_ITEM_FUNCTION_P(_T(MSG_SET_NOT_READY), lcd_printer_ready_state_toggle);
|
||||
} else {
|
||||
MENU_ITEM_FUNCTION_P(_T(MSG_SET_READY), lcd_printer_ready_state_toggle);
|
||||
}
|
||||
}
|
||||
}
|
||||
if (mesh_bed_leveling_flag == false
|
||||
&& homing_flag == false
|
||||
&& !printingIsPaused()
|
||||
&& !processing_tcode) {
|
||||
if (usb_timer.running()) {
|
||||
MENU_ITEM_FUNCTION_P(_T(MSG_PAUSE_PRINT), lcd_pause_usb_print);
|
||||
} else if (IS_SD_PRINTING) {
|
||||
MENU_ITEM_FUNCTION_P(_T(MSG_PAUSE_PRINT), lcd_pause_print);
|
||||
}
|
||||
}
|
||||
}
|
||||
if (mesh_bed_leveling_flag == false && homing_flag == false && !printingIsPaused() && !processing_tcode) {
|
||||
if (usb_timer.running()) {
|
||||
MENU_ITEM_FUNCTION_P(_T(MSG_PAUSE_PRINT), lcd_pause_usb_print);
|
||||
} else if (IS_SD_PRINTING) {
|
||||
MENU_ITEM_FUNCTION_P(_T(MSG_PAUSE_PRINT), lcd_pause_print);
|
||||
}
|
||||
}
|
||||
if(printingIsPaused())
|
||||
{
|
||||
if (printingIsPaused()
|
||||
// only allow resuming if hardware errors (temperature or fan) are cleared
|
||||
if(!get_temp_error()
|
||||
&& !get_temp_error()
|
||||
#ifdef FANCHECK
|
||||
&& fan_check_error != EFCE_REPORTED
|
||||
&& fan_check_error != EFCE_REPORTED
|
||||
#endif //FANCHECK
|
||||
) {
|
||||
if (saved_printing) {
|
||||
&& (saved_printing_type != PowerPanic::PRINT_TYPE_NONE
|
||||
|| saved_printing)
|
||||
&& custom_message_type != CustomMsg::Resuming) {
|
||||
if (saved_printing_type == PowerPanic::PRINT_TYPE_SD) {
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_RESUME_PRINT), lcd_resume_print);
|
||||
} else {
|
||||
} else if ((saved_printing_type == PowerPanic::PRINT_TYPE_HOST)
|
||||
&& (M79_timer_get_status())) {
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_RESUME_PRINT), lcd_resume_usb_print);
|
||||
}
|
||||
}
|
||||
}
|
||||
if((printJobOngoing()
|
||||
|
|
@ -5301,81 +5314,96 @@ static void lcd_main_menu()
|
|||
#endif
|
||||
|
||||
// only allow starting SD print if hardware errors (temperature or fan) are cleared
|
||||
if(!get_temp_error()
|
||||
&& !printer_active()
|
||||
if (!printer_recovering()
|
||||
&& !printer_active()
|
||||
&& !get_temp_error()
|
||||
&& !printer_active()
|
||||
#ifdef FANCHECK
|
||||
&& fan_check_error != EFCE_REPORTED
|
||||
&& fan_check_error != EFCE_REPORTED
|
||||
#endif //FANCHECK
|
||||
)
|
||||
{
|
||||
) {
|
||||
#ifdef SDSUPPORT //!@todo SDSUPPORT undefined creates several issues in source code
|
||||
if (card.mounted || lcd_commands_type != LcdCommands::Idle) {
|
||||
if (!card.isFileOpen()) {
|
||||
if (!usb_timer.running() && (lcd_commands_type == LcdCommands::Idle)) {
|
||||
bMain=true; // flag ('fake parameter') for 'lcd_sdcard_menu()' function
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_CARD_MENU), lcd_sdcard_menu);
|
||||
}
|
||||
if (card.mounted
|
||||
|| lcd_commands_type != LcdCommands::Idle) {
|
||||
if (!card.isFileOpen()) {
|
||||
if (!usb_timer.running()
|
||||
&& (lcd_commands_type == LcdCommands::Idle)) {
|
||||
bMain=true; // flag ('fake parameter') for 'lcd_sdcard_menu()' function
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_CARD_MENU), lcd_sdcard_menu);
|
||||
}
|
||||
#if SDCARDDETECT < 1
|
||||
MENU_ITEM_GCODE_P(_i("Change SD card"), PSTR("M21")); // SD-card changed by user ////MSG_CNG_SDCARD c=18
|
||||
MENU_ITEM_GCODE_P(_i("Change SD card"), PSTR("M21")); // SD-card changed by user ////MSG_CNG_SDCARD c=18
|
||||
#endif //SDCARDDETECT
|
||||
}
|
||||
} else {
|
||||
bMain=true; // flag (i.e. 'fake parameter') for 'lcd_sdcard_menu()' function
|
||||
MENU_ITEM_SUBMENU_P(_i("No SD card"), lcd_sdcard_menu); ////MSG_NO_CARD c=18
|
||||
}
|
||||
} else {
|
||||
bMain=true; // flag (i.e. 'fake parameter') for 'lcd_sdcard_menu()' function
|
||||
MENU_ITEM_BACK_P(_i("No SD card")); ////MSG_NO_CARD c=18
|
||||
#if SDCARDDETECT < 1
|
||||
MENU_ITEM_GCODE_P(_i("Init. SD card"), PSTR("M21")); // Manually initialize the SD-card via user interface ////MSG_INIT_SDCARD c=18
|
||||
#endif //SDCARDDETECT
|
||||
}
|
||||
}
|
||||
#endif //SDSUPPORT
|
||||
}
|
||||
|
||||
if(!printer_active() && !farm_mode) {
|
||||
const int8_t sheet = eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet));
|
||||
const int8_t nextSheet = eeprom_next_initialized_sheet(sheet);
|
||||
if ((nextSheet >= 0) && (sheet != nextSheet)) { // show menu only if we have 2 or more sheets initialized
|
||||
MENU_ITEM_FUNCTION_E(EEPROM_Sheets_base->s[sheet], eeprom_switch_to_next_sheet);
|
||||
}
|
||||
if(!printer_active()
|
||||
&& !farm_mode) {
|
||||
const int8_t sheet = eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet));
|
||||
const int8_t nextSheet = eeprom_next_initialized_sheet(sheet);
|
||||
if ((nextSheet >= 0)
|
||||
&& (sheet != nextSheet)) { // show menu only if we have 2 or more sheets initialized
|
||||
MENU_ITEM_FUNCTION_E(EEPROM_Sheets_base->s[sheet], eeprom_switch_to_next_sheet);
|
||||
}
|
||||
#ifdef QUICK_NOZZLE_CHANGE
|
||||
SETTINGS_NOZZLE;
|
||||
SETTINGS_NOZZLE;
|
||||
#endif //QUICK_NOZZLE_CHANGE
|
||||
|
||||
}
|
||||
|
||||
if ( ! ( printer_active() || (eFilamentAction != FilamentAction::None) || Stopped ) ) {
|
||||
if (MMU2::mmu2.Enabled()) {
|
||||
if(!MMU2::mmu2.FindaDetectsFilament() && !fsensor.getFilamentPresent()) {
|
||||
// The MMU 'Load filament' state machine will reject the command if any
|
||||
// filament sensor is reporting a detected filament
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_PRELOAD_TO_MMU), mmu_preload_filament_menu);
|
||||
}
|
||||
MENU_ITEM_SUBMENU_P(_i("Load to nozzle"), lcd_mmuLoadFilament);////MSG_LOAD_TO_NOZZLE c=18
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_UNLOAD_FILAMENT), lcd_mmuUnloadFilament);
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_EJECT_FROM_MMU), lcd_mmuEjectFilament);
|
||||
#ifdef MMU_HAS_CUTTER
|
||||
if (eeprom_read_byte((uint8_t*)EEPROM_MMU_CUTTER_ENABLED) != 0) {
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_CUT_FILAMENT), lcd_mmuCutFilament);
|
||||
}
|
||||
#endif //MMU_HAS_CUTTER
|
||||
} else {
|
||||
#ifdef FILAMENT_SENSOR
|
||||
if (fsensor.isEnabled() && fsensor.getAutoLoadEnabled()) {
|
||||
MENU_ITEM_SUBMENU_P(_i("AutoLoad filament"), lcd_menu_AutoLoadFilament);////MSG_AUTOLOAD_FILAMENT c=18
|
||||
}
|
||||
else
|
||||
#endif //FILAMENT_SENSOR
|
||||
{
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_LOAD_FILAMENT), lcd_LoadFilament);
|
||||
}
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_UNLOAD_FILAMENT), lcd_unLoadFilament);
|
||||
}
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_SETTINGS), lcd_settings_menu);
|
||||
if(!printingIsPaused()) MENU_ITEM_SUBMENU_P(_T(MSG_CALIBRATION), lcd_calibration_menu);
|
||||
|
||||
if (!( printer_active()
|
||||
|| (eFilamentAction != FilamentAction::None)
|
||||
|| Stopped )) {
|
||||
if (MMU2::mmu2.Enabled()) {
|
||||
if(!MMU2::mmu2.FindaDetectsFilament()
|
||||
&& !fsensor.getFilamentPresent()) {
|
||||
// The MMU 'Load filament' state machine will reject the command if any
|
||||
// filament sensor is reporting a detected filament
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_PRELOAD_TO_MMU), mmu_preload_filament_menu);
|
||||
}
|
||||
MENU_ITEM_SUBMENU_P(_i("Load to nozzle"), lcd_mmuLoadFilament);////MSG_LOAD_TO_NOZZLE c=18
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_UNLOAD_FILAMENT), lcd_mmuUnloadFilament);
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_EJECT_FROM_MMU), lcd_mmuEjectFilament);
|
||||
#ifdef MMU_HAS_CUTTER
|
||||
if (eeprom_read_byte((uint8_t*)EEPROM_MMU_CUTTER_ENABLED) != 0) {
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_CUT_FILAMENT), lcd_mmuCutFilament);
|
||||
}
|
||||
#endif //MMU_HAS_CUTTER
|
||||
} else {
|
||||
#ifdef FILAMENT_SENSOR
|
||||
if (fsensor.isEnabled()) {
|
||||
if (!fsensor.getFilamentPresent()) {
|
||||
if (fsensor.getAutoLoadEnabled()) {
|
||||
MENU_ITEM_SUBMENU_P(_i("AutoLoad filament"), lcd_menu_AutoLoadFilament);////MSG_AUTOLOAD_FILAMENT c=18
|
||||
} else {
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_LOAD_FILAMENT), lcd_LoadFilament);
|
||||
}
|
||||
} else {
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_UNLOAD_FILAMENT), lcd_unLoadFilament);
|
||||
}
|
||||
} else {
|
||||
#endif //FILAMENT_SENSOR
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_LOAD_FILAMENT), lcd_LoadFilament);
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_UNLOAD_FILAMENT), lcd_unLoadFilament);
|
||||
#ifdef FILAMENT_SENSOR
|
||||
}
|
||||
#endif //FILAMENT_SENSOR
|
||||
}
|
||||
MENU_ITEM_SUBMENU_P(_T(MSG_SETTINGS), lcd_settings_menu);
|
||||
if(!printingIsPaused()) MENU_ITEM_SUBMENU_P(_T(MSG_CALIBRATION), lcd_calibration_menu);
|
||||
}
|
||||
}
|
||||
|
||||
MENU_ITEM_SUBMENU_P(_i("Statistics"), lcd_menu_statistics);////MSG_STATISTICS c=18
|
||||
|
||||
#if defined(TMC2130) || defined(FILAMENT_SENSOR)
|
||||
MENU_ITEM_SUBMENU_P(_i("Fail stats"), lcd_menu_fails_stats);////MSG_FAIL_STATS c=18
|
||||
MENU_ITEM_SUBMENU_P(_i("Fail stats"), lcd_menu_fails_stats);////MSG_FAIL_STATS c=18
|
||||
#endif
|
||||
if (MMU2::mmu2.Enabled()) {
|
||||
MENU_ITEM_SUBMENU_P(_i("Fail stats MMU"), lcd_menu_fails_stats_mmu);////MSG_MMU_FAIL_STATS c=18
|
||||
|
|
|
|||
Loading…
Reference in New Issue