diff --git a/Firmware/Marlin_main.cpp b/Firmware/Marlin_main.cpp index 45dd118c4..a2cbece56 100755 --- a/Firmware/Marlin_main.cpp +++ b/Firmware/Marlin_main.cpp @@ -1242,8 +1242,8 @@ void setup() // Once a firmware boots up, it forces at least a language selection, which changes // EEPROM_LANG to number lower than 0x0ff. // 1) Set a high power mode. + eeprom_update_byte((uint8_t*)EEPROM_SILENT, SILENT_MODE_OFF); #ifdef TMC2130 - eeprom_write_byte((uint8_t*)EEPROM_SILENT, 0); tmc2130_mode = TMC2130_MODE_NORMAL; #endif //TMC2130 eeprom_write_byte((uint8_t*)EEPROM_WIZARD_ACTIVE, 1); //run wizard @@ -2433,6 +2433,9 @@ void ramming() { #ifdef TMC2130 void force_high_power_mode(bool start_high_power_section) { +#ifdef PSU_Delta + if (start_high_power_section == true) enable_force_z(); +#endif //PSU_Delta uint8_t silent; silent = eeprom_read_byte((uint8_t*)EEPROM_SILENT); if (silent == 1) { diff --git a/Firmware/stepper.cpp b/Firmware/stepper.cpp index 710b135ec..52fedcde9 100644 --- a/Firmware/stepper.cpp +++ b/Firmware/stepper.cpp @@ -1564,10 +1564,6 @@ void st_current_init() //Initialize Digipot Motor Current { #ifdef MOTOR_CURRENT_PWM_XY_PIN uint8_t SilentMode = eeprom_read_byte((uint8_t*)EEPROM_SILENT); - if (SilentMode == 0xff){ //set power to High Power (MK2.5) or Normal Power (MK3, unused) - SilentMode = SILENT_MODE_POWER; - eeprom_update_byte((uint8_t*)EEPROM_SILENT, SilentMode); - } SilentModeMenu = SilentMode; pinMode(MOTOR_CURRENT_PWM_XY_PIN, OUTPUT); pinMode(MOTOR_CURRENT_PWM_Z_PIN, OUTPUT); diff --git a/Firmware/temperature.cpp b/Firmware/temperature.cpp index df8a39e09..cde7cd88e 100755 --- a/Firmware/temperature.cpp +++ b/Firmware/temperature.cpp @@ -505,7 +505,10 @@ void checkFanSpeed() // we may even send some info to the LCD from here fan_check_error = EFCE_FIXED; } - + if ((fan_check_error == EFCE_FIXED) && !PRINTER_ACTIVE){ + fan_check_error = EFCE_OK; //if the issue is fixed while the printer is doing nothing, reenable processing immediately. + lcd_reset_alert_level(); //for another fan speed error + } if ((fan_speed_errors[0] > max_extruder_fan_errors) && fans_check_enabled && (fan_check_error == EFCE_OK)) { fan_speed_errors[0] = 0; fanSpeedError(0); //extruder fan diff --git a/Firmware/ultralcd.cpp b/Firmware/ultralcd.cpp index f49528025..d08f536c1 100755 --- a/Firmware/ultralcd.cpp +++ b/Firmware/ultralcd.cpp @@ -1843,8 +1843,8 @@ static void lcd_menu_fails_stats_total() //! @code{.unparsed} //! |01234567890123456789| //! |Last print failures | c=20 r=1 -//! | Power failures: 000| c=14 r=1 -//! | Filam. runouts: 000| c=14 r=1 +//! | Power failures 000| c=14 r=1 +//! | Filam. runouts 000| c=14 r=1 //! | Crash X:000 Y:000| c=7 r=1 //! ---------------------- //! @endcode @@ -1890,6 +1890,7 @@ static void lcd_menu_fails_stats() } #elif defined(FILAMENT_SENSOR) +static const char failStatsFmt[] PROGMEM = "%S\n" " %-16.16S%-3d\n" "%S\n" " %-16.16S%-3d\n"; //! //! @brief Print last print and total filament run outs //! @@ -1900,9 +1901,9 @@ static void lcd_menu_fails_stats() //! @code{.unparsed} //! |01234567890123456789| //! |Last print failures | c=20 r=1 -//! | Filam. runouts: 000| c=14 r=1 +//! | Filam. runouts 000| c=14 r=1 //! |Total failures | c=20 r=1 -//! | Filam. runouts: 000| c=14 r=1 +//! | Filam. runouts 000| c=14 r=1 //! ---------------------- //! @endcode //! @todo Positioning of the messages and values on LCD aren't fixed to their exact place. This causes issues with translations. @@ -1912,11 +1913,13 @@ static void lcd_menu_fails_stats() uint8_t filamentLast = eeprom_read_byte((uint8_t*)EEPROM_FERROR_COUNT); uint16_t filamentTotal = eeprom_read_word((uint16_t*)EEPROM_FERROR_COUNT_TOT); lcd_home(); - lcd_printf_P(PSTR("Last print failures\n" ////c=20 r=1 - " Filam. runouts %-3d\n" ////c=14 r=1 - "Total failures\n" ////c=20 r=1 - " Filam. runouts %-3d"), filamentLast, filamentTotal); ////c=14 r=1 - menu_back_if_clicked(); + lcd_printf_P(failStatsFmt, + _i("Last print failures"), ////c=20 r=1 + _i("Filam. runouts"), filamentLast, ////c=14 r=1 + _i("Total failures"), ////c=20 r=1 + _i("Filam. runouts"), filamentTotal); ////c=14 r=1 + + menu_back_if_clicked(); } #else static void lcd_menu_fails_stats() @@ -4929,12 +4932,12 @@ static void lcd_wizard_load() { if (mmu_enabled) { - lcd_show_fullscreen_message_and_wait_P(_i("Please insert filament to the first tube of MMU, then press the knob to load it."));////c=20 r=8 + lcd_show_fullscreen_message_and_wait_P(_i("Please insert filament into the first tube of the MMU, then press the knob to load it."));////c=20 r=8 tmp_extruder = 0; } else { - lcd_show_fullscreen_message_and_wait_P(_i("Please insert filament to the extruder, then press knob to load it."));////MSG_WIZARD_LOAD_FILAMENT c=20 r=8 + lcd_show_fullscreen_message_and_wait_P(_i("Please insert filament into the extruder, then press the knob to load it."));////MSG_WIZARD_LOAD_FILAMENT c=20 r=8 } lcd_update_enable(false); lcd_clear(); @@ -4958,7 +4961,7 @@ static void wizard_lay1cal_message(bool cold) if (mmu_enabled) { lcd_show_fullscreen_message_and_wait_P( - _i("First you will select filament you wish to use for calibration. Then select temperature which matches your material.")); + _i("Choose a filament for the First Layer Calibration and select it in the on-screen menu.")); } else if (cold) { @@ -4966,7 +4969,7 @@ static void wizard_lay1cal_message(bool cold) _i("Select temperature which matches your material.")); } lcd_show_fullscreen_message_and_wait_P( - _i("I will start to print line and you will gradually lower the nozzle by rotating the knob, until you reach optimal height. Check the pictures in our handbook in chapter Calibration.")); ////MSG_WIZARD_V2_CAL_2 c=20 r=12 + _i("The printer will start printing a zig-zag line. Rotate the knob until you reach the optimal height. Check the pictures in the handbook (Calibration chapter).")); ////MSG_WIZARD_V2_CAL_2 c=20 r=12 } //! @brief Printer first run wizard (Selftest and calibration) @@ -5094,7 +5097,7 @@ void lcd_wizard(WizState state) setTargetBed(PLA_PREHEAT_HPB_TEMP); if (mmu_enabled) { - wizard_event = lcd_show_fullscreen_message_yes_no_and_wait_P(_i("Is any filament loaded?"), true);////c=20 r=2 + wizard_event = lcd_show_fullscreen_message_yes_no_and_wait_P(_i("Is filament loaded?"), true);////c=20 r=2 } else { wizard_event = lcd_show_fullscreen_message_yes_no_and_wait_P(_i("Is filament loaded?"), true);////MSG_WIZARD_FILAMENT_LOADED c=20 r=2 @@ -5139,7 +5142,7 @@ void lcd_wizard(WizState state) } else { - lcd_show_fullscreen_message_and_wait_P(_i("If you have more steel sheets you can calibrate additional presets in Settings / HW Setup / Steel sheets.")); + lcd_show_fullscreen_message_and_wait_P(_i("If you have additional steel sheets, calibrate their presets in Settings - HW Setup - Steel sheets.")); state = S::Finish; } break; diff --git a/lang/lang-add.sh b/lang/lang-add.sh index 63349671b..945b1bf97 100755 --- a/lang/lang-add.sh +++ b/lang/lang-add.sh @@ -51,7 +51,7 @@ if ! [ -e lang_add.txt ]; then fi cat lang_add.txt | sed 's/^/"/;s/$/"/' | while read new_s; do - if grep "$new_s" lang_en.txt >/dev/nul; then + if grep "$new_s" lang_en.txt >/dev/null; then echo "text already exist:" echo "$new_s" echo diff --git a/lang/lang_en.txt b/lang/lang_en.txt index a7756bfe0..b1f952aa1 100755 --- a/lang/lang_en.txt +++ b/lang/lang_en.txt @@ -133,6 +133,9 @@ #MSG_CRASHDETECT_ON "Crash det. [on]" +# +"Choose a filament for the First Layer Calibration and select it in the on-screen menu." + #MSG_CRASHDETECT_NA "Crash det. [N/A]" @@ -361,6 +364,9 @@ # "Last print failures" +# +"If you have additional steel sheets, calibrate their presets in Settings - HW Setup - Steel sheets." + # "Last print" @@ -613,6 +619,15 @@ # "Print FAN" +# +"Please insert filament into the extruder, then press the knob to load it." + +# +"Please insert filament into the first tube of the MMU, then press the knob to load it." + +# +"Please load filament first." + #MSG_PRUSA3D "prusa3d.com" @@ -688,9 +703,6 @@ # "Select nozzle preheat temperature which matches your material." -# -"Select PLA filament:" - #MSG_SET_TEMPERATURE c=19 r=1 "Set temperature:" @@ -763,12 +775,18 @@ #MSG_SELFTEST_SWAPPED "Swapped" +# +"Select filament:" + #MSG_TEMP_CALIBRATION c=20 r=1 "Temp. cal. " #MSG_TEMP_CALIBRATION_ON c=20 r=1 "Temp. cal. [on]" +# +"Select temperature which matches your material." + #MSG_TEMP_CALIBRATION_OFF c=20 r=1 "Temp. cal. [off]" @@ -904,6 +922,9 @@ # "Y distance from min" +# +"The printer will start printing a zig-zag line. Rotate the knob until you reach the optimal height. Check the pictures in the handbook (Calibration chapter)." + # "Y-correct:" diff --git a/lang/lang_en_cz.txt b/lang/lang_en_cz.txt index 64673af42..c362b3f6b 100755 --- a/lang/lang_en_cz.txt +++ b/lang/lang_en_cz.txt @@ -72,7 +72,7 @@ #MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4 "Autoloading filament available only when filament sensor is turned on..." -"Automaticke zavadeni filamentu je dostupne pouze pri zapnutem filament senzoru..." +"Automaticke zavadeni filamentu je mozne pouze pri zapnutem filament senzoru..." #MSG_AUTOLOADING_ENABLED c=20 r=4 "Autoloading filament is active, just press the knob and insert filament..." @@ -178,6 +178,10 @@ "Crash det. [on]" "Crash det. [zap]" +# +"Choose a filament for the First Layer Calibration and select it in the on-screen menu." +"Zvolte filament pro kalibraci prvni vrstvy z nasledujiciho menu" + #MSG_CRASHDETECT_NA "Crash det. [N/A]" "\x00" @@ -482,6 +486,10 @@ "Last print failures" "Selhani posl. tisku" +# +"If you have additional steel sheets, calibrate their presets in Settings - HW Setup - Steel sheets." +"Mate-li vice tiskovych platu, kalibrujte je v menu Nastaveni - HW nastaveni - Tiskove platy" + # "Last print" "Posledni tisk" @@ -818,6 +826,18 @@ "Print FAN" "Tiskovy vent." +# +"Please insert filament into the extruder, then press the knob to load it." +"Prosim vlozte filament do extruderu a stisknete tlacitko k jeho zavedeni" + +# +"Please insert filament into the first tube of the MMU, then press the knob to load it." +"Prosim vlozte filament do prvni trubicky MMU a stisknete tlacitko k jeho zavedeni" + +# +"Please load filament first." +"Prosim nejdriv zavedte filament" + #MSG_PRUSA3D "prusa3d.com" "\x00" @@ -918,10 +938,6 @@ "Select nozzle preheat temperature which matches your material." "Vyberte teplotu predehrati trysky ktera odpovida vasemu materialu." -# -"Select PLA filament:" -"Vyberte PLA filament:" - #MSG_SET_TEMPERATURE c=19 r=1 "Set temperature:" "Nastavte teplotu:" @@ -1018,6 +1034,10 @@ "Swapped" "Prohozene" +# +"Select filament:" +"Zvolte filament:" + #MSG_TEMP_CALIBRATION c=20 r=1 "Temp. cal. " "Tepl. kal. " @@ -1026,6 +1046,10 @@ "Temp. cal. [on]" "Tepl. kal. [zap]" +# +"Select temperature which matches your material." +"Zvolte teplotu, ktera odpovida vasemu materialu." + #MSG_TEMP_CALIBRATION_OFF c=20 r=1 "Temp. cal. [off]" "Tepl. kal. [vyp]" @@ -1206,6 +1230,10 @@ "Y distance from min" "Y vzdalenost od min" +# +"The printer will start printing a zig-zag line. Rotate the knob until you reach the optimal height. Check the pictures in the handbook (Calibration chapter)." +"\x00" + # "Y-correct:" "Korekce Y:" diff --git a/lang/lang_en_de.txt b/lang/lang_en_de.txt index 0aec39d12..90181ebf3 100755 --- a/lang/lang_en_de.txt +++ b/lang/lang_en_de.txt @@ -178,6 +178,10 @@ "Crash det. [on]" "Crash Erk. [an]" +# +"Choose a filament for the First Layer Calibration and select it in the on-screen menu." +"Waehlen Sie ein Filament fuer Erste Schichtkalibrierung aus und waehlen Sie es im On-Screen-Menu aus." + #MSG_CRASHDETECT_NA "Crash det. [N/A]" "Crash Erk. [nv]" @@ -482,6 +486,10 @@ "Last print failures" "Letzte Druckfehler" +# +"If you have additional steel sheets, calibrate their presets in Settings - HW Setup - Steel sheets." +"Wenn Sie zusaetzliche Stahlbleche haben, kalibrieren Sie deren Voreinstellungen unter Einstellungen - HW Setup - Stahlbleche." + # "Last print" "Letzter Druck" @@ -818,6 +826,18 @@ "Print FAN" "Druckvent." +# +"Please insert filament into the extruder, then press the knob to load it." +"Bitte legen Sie das Filament in den Extruder ein und druecken Sie dann den Knopf, um es zu laden." + +# +"Please insert filament into the first tube of the MMU, then press the knob to load it." +"Bitte stecken Sie das Filament in den ersten Schlauch der MMU und druecken Sie dann den Knopf, um es zu laden." + +# +"Please load filament first." +"Bitte laden Sie zuerst das Filament." + #MSG_PRUSA3D "prusa3d.com" "\x00" @@ -918,10 +938,6 @@ "Select nozzle preheat temperature which matches your material." "Bitte Vorheiztemperatur auswaehlen, die Ihrem Material entspricht." -# -"Select PLA filament:" -"PLA Filament auswaehlen:" - #MSG_SET_TEMPERATURE c=19 r=1 "Set temperature:" "Temp. einstellen:" @@ -1018,6 +1034,10 @@ "Swapped" "Ausgetauscht" +# +"Select filament:" +"Filament auswaehlen:" + #MSG_TEMP_CALIBRATION c=20 r=1 "Temp. cal. " "Temp Kalib. " @@ -1026,6 +1046,10 @@ "Temp. cal. [on]" "Temp. Kal. [an]" +# +"Select temperature which matches your material." +"Waehlen Sie die Temperatur, die zu Ihrem Material passt." + #MSG_TEMP_CALIBRATION_OFF c=20 r=1 "Temp. cal. [off]" "Temp. Kal. [aus]" @@ -1202,11 +1226,14 @@ "XYZ calibration failed. Right front calibration point not reachable." "XYZ-Kalibrierung fehlgeschlagen. Rechter vorderer Kalibrierpunkt ist nicht erreichbar." - # "Y distance from min" "Y Entfernung vom Min" +# +"The printer will start printing a zig-zag line. Rotate the knob until you reach the optimal height. Check the pictures in the handbook (Calibration chapter)." +"\x00" + # "Y-correct:" "Y-Korrektur:" diff --git a/lang/lang_en_es.txt b/lang/lang_en_es.txt index 3f6007c88..efb3a85bb 100755 --- a/lang/lang_en_es.txt +++ b/lang/lang_en_es.txt @@ -72,11 +72,11 @@ #MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4 "Autoloading filament available only when filament sensor is turned on..." -"La carga automatica de filamento solo funciona si el sensor de filamento esta activado..." +"La carga automatica solo funciona si el sensor de filamento esta activado..." #MSG_AUTOLOADING_ENABLED c=20 r=4 "Autoloading filament is active, just press the knob and insert filament..." -"La carga automatica de filamento esta activada, pulse el dial e inserte el filamento..." +"La carga automatica esta activada, pulse el dial e inserte el filamento..." #MSG_SELFTEST_AXIS_LENGTH "Axis length" @@ -178,6 +178,10 @@ "Crash det. [on]" "Det. choque [act]" +# +"Choose a filament for the First Layer Calibration and select it in the on-screen menu." +"Escoge un filamento para la Calibracion de la Primera Capa y seleccionalo en el menu en pantalla." + #MSG_CRASHDETECT_NA "Crash det. [N/A]" "Dec. choque [N/D]" @@ -482,6 +486,10 @@ "Last print failures" "Ultimas impresiones fallidas" +# +"If you have additional steel sheets, calibrate their presets in Settings - HW Setup - Steel sheets." +"Si tienes planchas de acero adicionales, calibra sus ajustes en Ajustes - Ajustes HW - Planchas acero." + # "Last print" "Ultima impresion" @@ -818,6 +826,18 @@ "Print FAN" "Vent. extr" +# +"Please insert filament into the extruder, then press the knob to load it." +"Por favor, coloca el filamento en el extrusor, luego presiona el dial para cargarlo." + +# +"Please insert filament into the first tube of the MMU, then press the knob to load it." +"Por favor, coloca el filamento en el primer tubo de la MMU, luego pulsa el dial para cargarlo." + +# +"Please load filament first." +"Por favor, cargar primero el filamento. " + #MSG_PRUSA3D "prusa3d.com" "prusa3d.es" @@ -918,10 +938,6 @@ "Select nozzle preheat temperature which matches your material." "Selecciona la temperatura para precalentar la boquilla que se ajuste a tu material. " -# -"Select PLA filament:" -"Seleccionar filamento PLA:" - #MSG_SET_TEMPERATURE c=19 r=1 "Set temperature:" "Establecer temp.:" @@ -1018,6 +1034,10 @@ "Swapped" "Intercambiado" +# +"Select filament:" +"Selecciona filamento:" + #MSG_TEMP_CALIBRATION c=20 r=1 "Temp. cal. " "Cal. temp. " @@ -1026,6 +1046,10 @@ "Temp. cal. [on]" "Cal. temp. [on]" +# +"Select temperature which matches your material." +"Selecciona la temperatura adecuada a tu material." + #MSG_TEMP_CALIBRATION_OFF c=20 r=1 "Temp. cal. [off]" "Cal. temp. [off]" @@ -1206,6 +1230,10 @@ "Y distance from min" "Distancia en Y desde el min" +# +"The printer will start printing a zig-zag line. Rotate the knob until you reach the optimal height. Check the pictures in the handbook (Calibration chapter)." +"\x00" + # "Y-correct:" "Corregir-Y:" diff --git a/lang/lang_en_fr.txt b/lang/lang_en_fr.txt index 729778c27..90fd096e1 100755 --- a/lang/lang_en_fr.txt +++ b/lang/lang_en_fr.txt @@ -178,6 +178,10 @@ "Crash det. [on]" "Detect.crash [on]" +# +"Choose a filament for the First Layer Calibration and select it in the on-screen menu." +"Choisissez un filament pour la Calibration de la Premiere Couche et selectionnez-le depuis le menu a l'ecran." + #MSG_CRASHDETECT_NA "Crash det. [N/A]" "Detect.crash[N/A]" @@ -482,6 +486,10 @@ "Last print failures" "Echecs derniere imp." +# +"If you have additional steel sheets, calibrate their presets in Settings - HW Setup - Steel sheets." +"Si vous avez d'autres feuilles d'acier, calibrez leurs pre-reglages dans Reglages - Config HW - Feuilles d'acier." + # "Last print" "Derniere impres." @@ -818,6 +826,18 @@ "Print FAN" "Vent. impr" +# +"Please insert filament into the extruder, then press the knob to load it." +"Veuillez inserer le filament dans l'extrudeur, puis appuyez sur le bouton pour le charger." + +# +"Please insert filament into the first tube of the MMU, then press the knob to load it." +"Veuillez inserer le filament dans le premier tube du MMU, puis appuyez sur le bouton pour le charger." + +# +"Please load filament first." +"Veuillez d'abord charger un filament." + #MSG_PRUSA3D "prusa3d.com" "\x00" @@ -918,10 +938,6 @@ "Select nozzle preheat temperature which matches your material." "Selectionnez la temperature de prechauffage de la buse qui correspond a votre materiau." -# -"Select PLA filament:" -"Selectionnez le fil. PLA:" - #MSG_SET_TEMPERATURE c=19 r=1 "Set temperature:" "Regler temp.:" @@ -1018,6 +1034,10 @@ "Swapped" "Echange" +# +"Select filament:" +"Selectionnez le filament:" + #MSG_TEMP_CALIBRATION c=20 r=1 "Temp. cal. " "Calib. Temp." @@ -1026,6 +1046,10 @@ "Temp. cal. [on]" "Calib. Temp. [on]" +# +"Select temperature which matches your material." +"Selectionnez la temperature qui correspond a votre materiau." + #MSG_TEMP_CALIBRATION_OFF c=20 r=1 "Temp. cal. [off]" "Calib. Temp.[off]" @@ -1206,6 +1230,10 @@ "Y distance from min" "Distance Y du min" +# +"The printer will start printing a zig-zag line. Rotate the knob until you reach the optimal height. Check the pictures in the handbook (Calibration chapter)." +"\x00" + # "Y-correct:" "Correct-Y:" diff --git a/lang/lang_en_it.txt b/lang/lang_en_it.txt index 4d175221f..4333041d3 100755 --- a/lang/lang_en_it.txt +++ b/lang/lang_en_it.txt @@ -178,6 +178,10 @@ "Crash det. [on]" "Rileva.crash [on]" +# +"Choose a filament for the First Layer Calibration and select it in the on-screen menu." +"Scegli un filamento per la calibrazione del primo strato e selezionalo nel menu sullo schermo." + #MSG_CRASHDETECT_NA "Crash det. [N/A]" "Rileva.crash[N/A]" @@ -482,6 +486,10 @@ "Last print failures" "Fallimenti ultima stampa" +# +"If you have additional steel sheets, calibrate their presets in Settings - HW Setup - Steel sheets." +"Se hai piastre d'acciaio aggiuntive, calibra i preset in Impostazioni - Setup HW - Piastre in Acciaio." + # "Last print" "Ultima stampa" @@ -818,6 +826,18 @@ "Print FAN" "Ventola di stampa" +# +"Please insert filament into the extruder, then press the knob to load it." +"Inserisci il filamento nell'estrusore, poi premi la manopola per caricarlo." + +# +"Please insert filament into the first tube of the MMU, then press the knob to load it." +"Per favore inserisci il filamento nel primo tubo del MMU, poi premi la manopola per caricarlo." + +# +"Please load filament first." +"Per favore prima carica il filamento." + #MSG_PRUSA3D "prusa3d.com" "\x00" @@ -918,10 +938,6 @@ "Select nozzle preheat temperature which matches your material." "Selezionate la temperatura per il preriscaldamento dell'ugello adatta al vostro materiale." -# -"Select PLA filament:" -"Selezionate filamento PLA:" - #MSG_SET_TEMPERATURE c=19 r=1 "Set temperature:" "Imposta temperatura:" @@ -1018,6 +1034,10 @@ "Swapped" "Scambiato" +# +"Select filament:" +"Seleziona il filamento:" + #MSG_TEMP_CALIBRATION c=20 r=1 "Temp. cal. " "Calib. temp. " @@ -1026,6 +1046,10 @@ "Temp. cal. [on]" "Calib. temp. [on]" +# +"Select temperature which matches your material." +"Seleziona la temperatura appropriata per il tuo materiale." + #MSG_TEMP_CALIBRATION_OFF c=20 r=1 "Temp. cal. [off]" "Calib. temp.[off]" @@ -1206,6 +1230,10 @@ "Y distance from min" "Distanza Y dal min" +# +"The printer will start printing a zig-zag line. Rotate the knob until you reach the optimal height. Check the pictures in the handbook (Calibration chapter)." +"\x00" + # "Y-correct:" "Correzione-Y:" diff --git a/lang/lang_en_pl.txt b/lang/lang_en_pl.txt index 9e6d8e707..29d48ed8a 100755 --- a/lang/lang_en_pl.txt +++ b/lang/lang_en_pl.txt @@ -72,7 +72,7 @@ #MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4 "Autoloading filament available only when filament sensor is turned on..." -"Autoladowanie filamentu dostepne tylko gdy czujnik filamentu jest wlaczony..." +"Autoladowanie fil. dostepne tylko gdy czujnik filamentu jest wlaczony..." #MSG_AUTOLOADING_ENABLED c=20 r=4 "Autoloading filament is active, just press the knob and insert filament..." @@ -178,6 +178,10 @@ "Crash det. [on]" "Wykr.zderzen [wl]" +# +"Choose a filament for the First Layer Calibration and select it in the on-screen menu." +"Wybierz filament do Kalibracji Pierwszej Warstwy i potwierdz w menu ekranowym." + #MSG_CRASHDETECT_NA "Crash det. [N/A]" "Wykr.zderzen[N/D]" @@ -482,6 +486,10 @@ "Last print failures" "Ostatnie bledy druku" +# +"If you have additional steel sheets, calibrate their presets in Settings - HW Setup - Steel sheets." +"Jesli masz dodatkowe plyty stalowe, to skalibruj ich ustawienia w menu Ustawienia - Ustawienia HW - Plyty stalowe." + # "Last print" "Ost. wydruk" @@ -818,6 +826,18 @@ "Print FAN" "WentWydruk" +# +"Please insert filament into the extruder, then press the knob to load it." +"Wsun filament do ekstrudera i nacisnij pokretlo, aby go zaladowac." + +# +"Please insert filament into the first tube of the MMU, then press the knob to load it." +"Wsun filament do pierwszego kanalu w MMU2 i nacisnij pokretlo, aby go zaladowac." + +# +"Please load filament first." +"Najpierw zaladuj filament." + #MSG_PRUSA3D "prusa3d.com" "\x00" @@ -918,10 +938,6 @@ "Select nozzle preheat temperature which matches your material." "Wybierz temperature grzania dyszy odpowiednia dla materialu." -# -"Select PLA filament:" -"Wybierz filament PLA:" - #MSG_SET_TEMPERATURE c=19 r=1 "Set temperature:" "Ustaw temperature:" @@ -1018,6 +1034,10 @@ "Swapped" "Zamieniono" +# +"Select filament:" +"Wybierz filament:" + #MSG_TEMP_CALIBRATION c=20 r=1 "Temp. cal. " "Kalibracja temp." @@ -1026,6 +1046,10 @@ "Temp. cal. [on]" "Kalibr.temp. [wl]" +# +"Select temperature which matches your material." +"Wybierz temperature, ktora odpowiada Twojemu filamentowi." + #MSG_TEMP_CALIBRATION_OFF c=20 r=1 "Temp. cal. [off]" "Kalibr.temp.[wyl]" @@ -1206,6 +1230,10 @@ "Y distance from min" "Dystans od 0 w osi Y" +# +"The printer will start printing a zig-zag line. Rotate the knob until you reach the optimal height. Check the pictures in the handbook (Calibration chapter)." +"\x00" + # "Y-correct:" "Korekcja-Y:"