Merge branch 'MK3' into MK3_prep_Arudino-Boards_102

Firmware/Configuration.h

@@ -16,8 +16,8 @@ extern uint16_t nPrinterType;
 extern PGM_P sPrinterName;
 
 // Firmware version
-#define FW_VERSION "3.8.0"
+#define FW_VERSION "3.8.1-RC1"
-#define FW_COMMIT_NR   2684
+#define FW_COMMIT_NR   2851
 // FW_VERSION_UNKNOWN means this is an unofficial build.
 // The firmware should only be checked into github with this symbol.
 #define FW_DEV_VERSION FW_VERSION_UNKNOWN

Firmware/Marlin_main.cpp

@@ -1234,6 +1234,21 @@ void setup()
 	plan_init();  // Initialize planner;
 
 	factory_reset();
+	if (eeprom_read_dword((uint32_t*)(EEPROM_TOP - 4)) == 0x0ffffffff &&
+	        eeprom_read_dword((uint32_t*)(EEPROM_TOP - 8)) == 0x0ffffffff)
+	{
+        // Maiden startup. The firmware has been loaded and first started on a virgin RAMBo board,
+        // where all the EEPROM entries are set to 0x0ff.
+        // Once a firmware boots up, it forces at least a language selection, which changes
+        // EEPROM_LANG to number lower than 0x0ff.
+        // 1) Set a high power mode.
+#ifdef TMC2130
+        eeprom_write_byte((uint8_t*)EEPROM_SILENT, 0);
+        tmc2130_mode = TMC2130_MODE_NORMAL;
+#endif //TMC2130
+        eeprom_write_byte((uint8_t*)EEPROM_WIZARD_ACTIVE, 1); //run wizard
+    }
+
     lcd_encoder_diff=0;
 
 #ifdef TMC2130
@@ -1345,20 +1360,6 @@ void setup()
 	// Enable Toshiba FlashAir SD card / WiFi enahanced card.
 	card.ToshibaFlashAir_enable(eeprom_read_byte((unsigned char*)EEPROM_TOSHIBA_FLASH_AIR_COMPATIBLITY) == 1);
 
-	if (eeprom_read_dword((uint32_t*)(EEPROM_TOP - 4)) == 0x0ffffffff &&
-		eeprom_read_dword((uint32_t*)(EEPROM_TOP - 8)) == 0x0ffffffff) {
-		// Maiden startup. The firmware has been loaded and first started on a virgin RAMBo board,
-		// where all the EEPROM entries are set to 0x0ff.
-		// Once a firmware boots up, it forces at least a language selection, which changes
-		// EEPROM_LANG to number lower than 0x0ff.
-		// 1) Set a high power mode.
-#ifdef TMC2130
-		eeprom_write_byte((uint8_t*)EEPROM_SILENT, 0);
-		tmc2130_mode = TMC2130_MODE_NORMAL;
-#endif //TMC2130
-		eeprom_write_byte((uint8_t*)EEPROM_WIZARD_ACTIVE, 1); //run wizard
-	}
-
 	// Force SD card update. Otherwise the SD card update is done from loop() on card.checkautostart(false), 
 	// but this times out if a blocking dialog is shown in setup().
 	card.initsd();

lang/lang_en.txt

@@ -1,3 +1,6 @@
+#
+"[%.7s]Live adj. Z\x0avalue set, continue\x0aor start from zero?\x0a%cContinue%cReset"
+
 #MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE2 c=14
 " of 4"
 

lang/lang_en_cz.txt

@@ -1,3 +1,7 @@
+#
+"[%.7s]Live adj. Z\x0avalue set, continue\x0aor start from zero?\x0a%cContinue%cReset"
+"[%.7s]Doladeni Z\x0auz nastaveno, pouzit\x0anebo reset od nuly?\x0a%cPokracovat%cReset"
+
 #MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE2 c=14
 " of 4"
 " z 4"

lang/lang_en_de.txt

@@ -1,3 +1,7 @@
+#
+"[%.7s]Live adj. Z\x0avalue set, continue\x0aor start from zero?\x0a%cContinue%cReset"
+"[%.7s]Z Einstell.\x0aWert gesetzt,weiter\x0aoder mit 0 beginnen?\x0a%cWeiter%cNeu beginnen"
+
 #MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE2 c=14
 " of 4"
 " von 4"
@@ -852,7 +856,7 @@
 
 #MSG_BED_CORRECTION_RIGHT c=14 r=1
 "Right side[um]"
-"Rechts    [um]"
+"Rechts [um]"
 
 #MSG_SECOND_SERIAL_ON c=17 r=1
 "RPi port     [on]"

lang/lang_en_es.txt

@@ -1,3 +1,7 @@
+#
+"[%.7s]Live adj. Z\x0avalue set, continue\x0aor start from zero?\x0a%cContinue%cReset"
+"[%.7s]Ajuste Z\x0aAjustado, continuar\x0ao empezar de nuevo?\x0a%cContinuar%cRepetir"
+
 #MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE2 c=14
 " of 4"
 " de 4"
@@ -812,7 +816,7 @@
 
 #
 "Print FAN"
-"Vent.extr"
+"Vent. extr"
 
 #MSG_PRUSA3D
 "prusa3d.com"
@@ -1052,11 +1056,11 @@
 
 #
 "Total filament"
-"Filamento total:"
+"Filamento total"
 
 #
 "Total print time"
-"Tiempo total :"
+"Tiempo total"
 
 #MSG_TUNE
 "Tune"

lang/lang_en_fr.txt

@@ -1,10 +1,14 @@
+#
+"[%.7s]Live adj. Z\x0avalue set, continue\x0aor start from zero?\x0a%cContinue%cReset"
+"[%.7s]Ajust. du Z\x0aValeur enreg, contin\x0aou depart a zero?\x0a%cContinuer%cReset"
+
 #MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE2 c=14
 " of 4"
-"de 4"
+" de 4"
 
 #MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
 " of 9"
-"de 9"
+" de 9"
 
 #MSG_MEASURED_OFFSET
 "[0;0] point offset"
@@ -872,7 +876,7 @@
 
 #MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
 "SD card [flshAir]"
-"CarteSD [flshAir]"
+"Carte SD[flshAir]"
 
 #
 "Right"

lang/lang_en_it.txt

@@ -1,10 +1,14 @@
+#
+"[%.7s]Live adj. Z\x0avalue set, continue\x0aor start from zero?\x0a%cContinue%cReset"
+"[%.7s]Set valori\x0aComp. Z, continuare\x0ao iniziare da zero?\x0a%cContinua%cReset"
+
 #MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE2 c=14
 " of 4"
 " su 4"
 
 #MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
 " of 9"
-"su 9"
+" su 9"
 
 #MSG_MEASURED_OFFSET
 "[0;0] point offset"
@@ -492,7 +496,7 @@
 
 #MSG_BED_CORRECTION_LEFT c=14 r=1
 "Left side [um]"
-"Sinistra  [um]"
+"Sinistra [um]"
 
 #
 "Lin. correction"

lang/lang_en_pl.txt

@@ -1,3 +1,7 @@
+#
+"[%.7s]Live adj. Z\x0avalue set, continue\x0aor start from zero?\x0a%cContinue%cReset"
+"[%.7s]Live Adj. Z\x0austaw., kontynuowac\x0aczy zaczac od 0?\x0a%cKontynuuj%cReset"
+
 #MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE2 c=14
 " of 4"
 " z 4"