Rename minsegmenttime --> min_segment_time_us
Also fixed wrong unit in Configuration prinout (M500) should be us and not ms Also used %lu format for uint32_t instead of %.2f
This commit is contained in:
Guðni Már Gilbert
DRracer
parent
842dcc6560
commit
f40defd2a9
|
|
@ -27,7 +27,7 @@ void Config_PrintSettings(uint8_t level)
|
|||
"%SMaximum acceleration - normal (mm/s2):\n%S M201 X%lu Y%lu Z%lu E%lu\n"
|
||||
"%SMaximum acceleration - stealth (mm/s2):\n%S M201 X%lu Y%lu Z%lu E%lu\n"
|
||||
"%SAcceleration: P=print, R=retract, T=travel\n%S M204 P%.2f R%.2f T%.2f\n"
|
||||
"%SAdvanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)\n%S M205 S%.2f T%.2f B%.2f X%.2f Y%.2f Z%.2f E%.2f\n"
|
||||
"%SAdvanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (us), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)\n%S M205 S%.2f T%.2f B%lu X%.2f Y%.2f Z%.2f E%.2f\n"
|
||||
"%SHome offset (mm):\n%S M206 X%.2f Y%.2f Z%.2f\n"
|
||||
),
|
||||
echomagic, echomagic, cs.axis_steps_per_mm[X_AXIS], cs.axis_steps_per_mm[Y_AXIS], cs.axis_steps_per_mm[Z_AXIS], cs.axis_steps_per_mm[E_AXIS],
|
||||
|
|
@ -37,7 +37,7 @@ void Config_PrintSettings(uint8_t level)
|
|||
echomagic, echomagic, cs.max_acceleration_mm_per_s2_normal[X_AXIS], cs.max_acceleration_mm_per_s2_normal[Y_AXIS], cs.max_acceleration_mm_per_s2_normal[Z_AXIS], cs.max_acceleration_mm_per_s2_normal[E_AXIS],
|
||||
echomagic, echomagic, cs.max_acceleration_mm_per_s2_silent[X_AXIS], cs.max_acceleration_mm_per_s2_silent[Y_AXIS], cs.max_acceleration_mm_per_s2_silent[Z_AXIS], cs.max_acceleration_mm_per_s2_silent[E_AXIS],
|
||||
echomagic, echomagic, cs.acceleration, cs.retract_acceleration, cs.travel_acceleration,
|
||||
echomagic, echomagic, cs.minimumfeedrate, cs.mintravelfeedrate, cs.minsegmenttime, cs.max_jerk[X_AXIS], cs.max_jerk[Y_AXIS], cs.max_jerk[Z_AXIS], cs.max_jerk[E_AXIS],
|
||||
echomagic, echomagic, cs.minimumfeedrate, cs.mintravelfeedrate, cs.min_segment_time_us, cs.max_jerk[X_AXIS], cs.max_jerk[Y_AXIS], cs.max_jerk[Z_AXIS], cs.max_jerk[E_AXIS],
|
||||
echomagic, echomagic, cs.add_homing[X_AXIS], cs.add_homing[Y_AXIS], cs.add_homing[Z_AXIS]
|
||||
#else //TMC2130
|
||||
printf_P(PSTR(
|
||||
|
|
@ -45,14 +45,14 @@ void Config_PrintSettings(uint8_t level)
|
|||
"%SMaximum feedrates (mm/s):\n%S M203 X%.2f Y%.2f Z%.2f E%.2f\n"
|
||||
"%SMaximum acceleration (mm/s2):\n%S M201 X%lu Y%lu Z%lu E%lu\n"
|
||||
"%SAcceleration: P=print, R=retract, T=travel\n%S M204 P%.2f R%.2f T%.2f\n"
|
||||
"%SAdvanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)\n%S M205 S%.2f T%.2f B%.2f X%.2f Y%.2f Z%.2f E%.2f\n"
|
||||
"%SAdvanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (us), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)\n%S M205 S%.2f T%.2f B%lu X%.2f Y%.2f Z%.2f E%.2f\n"
|
||||
"%SHome offset (mm):\n%S M206 X%.2f Y%.2f Z%.2f\n"
|
||||
),
|
||||
echomagic, echomagic, cs.axis_steps_per_mm[X_AXIS], cs.axis_steps_per_mm[Y_AXIS], cs.axis_steps_per_mm[Z_AXIS], cs.axis_steps_per_mm[E_AXIS],
|
||||
echomagic, echomagic, max_feedrate[X_AXIS], max_feedrate[Y_AXIS], max_feedrate[Z_AXIS], max_feedrate[E_AXIS],
|
||||
echomagic, echomagic, max_acceleration_mm_per_s2[X_AXIS], max_acceleration_mm_per_s2[Y_AXIS], max_acceleration_mm_per_s2[Z_AXIS], max_acceleration_mm_per_s2[E_AXIS],
|
||||
echomagic, echomagic, cs.acceleration, cs.retract_acceleration, cs.travel_acceleration,
|
||||
echomagic, echomagic, cs.minimumfeedrate, cs.mintravelfeedrate, cs.minsegmenttime, cs.max_jerk[X_AXIS], cs.max_jerk[Y_AXIS], cs.max_jerk[Z_AXIS], cs.max_jerk[E_AXIS],
|
||||
echomagic, echomagic, cs.minimumfeedrate, cs.mintravelfeedrate, cs.min_segment_time_us, cs.max_jerk[X_AXIS], cs.max_jerk[Y_AXIS], cs.max_jerk[Z_AXIS], cs.max_jerk[E_AXIS],
|
||||
echomagic, echomagic, cs.add_homing[X_AXIS], cs.add_homing[Y_AXIS], cs.add_homing[Z_AXIS]
|
||||
#endif //TMC2130
|
||||
);
|
||||
|
|
|
|||
|
|
@ -16,7 +16,7 @@ typedef struct
|
|||
float retract_acceleration; //!< mm/s^2 filament pull-pack and push-forward while standing still in the other axis M204 TXXXX
|
||||
float minimumfeedrate;
|
||||
float mintravelfeedrate;
|
||||
unsigned long minsegmenttime;
|
||||
uint32_t min_segment_time_us; //!< (µs) M205 B
|
||||
float max_jerk[4]; //!< Jerk is a maximum immediate velocity change.
|
||||
float add_homing[3];
|
||||
float zprobe_zoffset; //!< Only used with define ENABLE_AUTO_BED_LEVELING
|
||||
|
|
|
|||
|
|
@ -6318,31 +6318,30 @@ Sigma_Exit:
|
|||
M92 [ X | Y | Z | E ]
|
||||
|
||||
#### Parameters
|
||||
- `X` - Steps per unit for the X drive
|
||||
- `Y` - Steps per unit for the Y drive
|
||||
- `Z` - Steps per unit for the Z drive
|
||||
- `E` - Steps per unit for the extruder drive
|
||||
- `X` - Steps per mm for the X drive
|
||||
- `Y` - Steps per mm for the Y drive
|
||||
- `Z` - Steps per mm for the Z drive
|
||||
- `E` - Steps per mm for the extruder drive
|
||||
*/
|
||||
case 92:
|
||||
for(int8_t i=0; i < NUM_AXIS; i++)
|
||||
{
|
||||
if(code_seen(axis_codes[i]))
|
||||
{
|
||||
if(i == E_AXIS) { // E
|
||||
float value = code_value();
|
||||
if(i == E_AXIS) { // E
|
||||
if(value < 20.0) {
|
||||
float factor = cs.axis_steps_per_mm[i] / value; // increase e constants if M92 E14 is given for netfab.
|
||||
const float factor = cs.axis_steps_per_mm[E_AXIS] / value; // increase e constants if M92 E14 is given for netfab.
|
||||
cs.max_jerk[E_AXIS] *= factor;
|
||||
max_feedrate[i] *= factor;
|
||||
max_acceleration_steps_per_s2[i] *= factor;
|
||||
max_feedrate[E_AXIS] *= factor;
|
||||
max_acceleration_steps_per_s2[E_AXIS] *= factor;
|
||||
}
|
||||
cs.axis_steps_per_mm[i] = value;
|
||||
cs.axis_steps_per_mm[E_AXIS] = value;
|
||||
#if defined(FILAMENT_SENSOR) && (FILAMENT_SENSOR_TYPE == FSENSOR_PAT9125)
|
||||
fsensor.init();
|
||||
#endif //defined(FILAMENT_SENSOR) && (FILAMENT_SENSOR_TYPE == FSENSOR_PAT9125)
|
||||
}
|
||||
else {
|
||||
cs.axis_steps_per_mm[i] = code_value();
|
||||
} else {
|
||||
cs.axis_steps_per_mm[i] = value;
|
||||
}
|
||||
}
|
||||
}
|
||||
|
|
@ -6807,7 +6806,7 @@ Sigma_Exit:
|
|||
{
|
||||
if(code_seen('S')) cs.minimumfeedrate = code_value();
|
||||
if(code_seen('T')) cs.mintravelfeedrate = code_value();
|
||||
if(code_seen('B')) cs.minsegmenttime = code_value() ;
|
||||
if(code_seen('B')) cs.min_segment_time_us = (uint32_t)code_value();
|
||||
if(code_seen('X')) cs.max_jerk[X_AXIS] = cs.max_jerk[Y_AXIS] = code_value();
|
||||
if(code_seen('Y')) cs.max_jerk[Y_AXIS] = code_value();
|
||||
if(code_seen('Z')) cs.max_jerk[Z_AXIS] = code_value();
|
||||
|
|
|
|||
|
|
@ -965,9 +965,9 @@ Having the real displacement of the head, we can calculate the total movement le
|
|||
if (moves_queued > 1 && moves_queued < (BLOCK_BUFFER_SIZE >> 1)) {
|
||||
// segment time in micro seconds
|
||||
unsigned long segment_time = lround(1000000.0/inverse_second);
|
||||
if (segment_time < cs.minsegmenttime)
|
||||
if (segment_time < cs.min_segment_time_us)
|
||||
// buffer is draining, add extra time. The amount of time added increases if the buffer is still emptied more.
|
||||
inverse_second=1000000.0/(segment_time+lround(2*(cs.minsegmenttime-segment_time)/moves_queued));
|
||||
inverse_second=1000000.0/(segment_time+lround(2*(cs.min_segment_time_us-segment_time)/moves_queued));
|
||||
}
|
||||
#endif // SLOWDOWN
|
||||
|
||||
|
|
|
|||
Loading…
Reference in New Issue