Fix lcd_print_stop function

Firmware/Marlin_main.cpp

@@ -4692,13 +4692,13 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 			// We don't know where we are! HOME!
 			// Push the commands to the front of the message queue in the reverse order!
 			// There shall be always enough space reserved for these commands.
-			if (lcd_commands_type != LcdCommands::StopPrint) {
+			// if (lcd_commands_type != LcdCommands::StopPrint) {
 				repeatcommand_front(); // repeat G80 with all its parameters
 				enquecommand_front_P((PSTR("G28 W0")));
-			}
+			// }
-			else {
+			// else {
-				mesh_bed_leveling_flag = false;
+				// mesh_bed_leveling_flag = false;
-			}
+			// }
 			break;
 		} 
 		
@@ -4728,23 +4728,23 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 #ifndef PINDA_THERMISTOR
 		if (run == false && temp_cal_active == true && calibration_status_pinda() == true && target_temperature_bed >= 50)
 		{
-			if (lcd_commands_type != LcdCommands::StopPrint) {
+			// if (lcd_commands_type != LcdCommands::StopPrint) {
 				temp_compensation_start();
 				run = true;
 				repeatcommand_front(); // repeat G80 with all its parameters
 				enquecommand_front_P((PSTR("G28 W0")));
-			}
+			// }
-			else {
+			// else {
-				mesh_bed_leveling_flag = false;
+				// mesh_bed_leveling_flag = false;
-			}
+			// }
 			break;
 		}
         run = false;
 #endif //PINDA_THERMISTOR
-		if (lcd_commands_type == LcdCommands::StopPrint) {
+		// if (lcd_commands_type == LcdCommands::StopPrint) {
-			mesh_bed_leveling_flag = false;
+			// mesh_bed_leveling_flag = false;
-			break;
+			// break;
-		}
+		// }
 		// Save custom message state, set a new custom message state to display: Calibrating point 9.
 		CustomMsg custom_message_type_old = custom_message_type;
 		unsigned int custom_message_state_old = custom_message_state;
@@ -8948,6 +8948,7 @@ static void wait_for_heater(long codenum, uint8_t extruder) {
 	residencyStart = -1;
 	/* continue to loop until we have reached the target temp
 	_and_ until TEMP_RESIDENCY_TIME hasn't passed since we reached it */
+    cancel_heatup = false;
 	while ((!cancel_heatup) && ((residencyStart == -1) ||
 		(residencyStart >= 0 && (((unsigned int)(_millis() - residencyStart)) < (TEMP_RESIDENCY_TIME * 1000UL))))) {
 #else

Firmware/ultralcd.cpp

@@ -250,7 +250,9 @@ static void fil_unload_menu();
 static void lcd_disable_farm_mode();
 static void lcd_set_fan_check();
 static void lcd_cutter_enabled();
+#ifdef SNMM
 static char snmm_stop_print_menu();
+#endif //SNMM
 #ifdef SDCARD_SORT_ALPHA
  static void lcd_sort_type_set();
 #endif
@@ -1056,7 +1058,7 @@ static void lcd_status_screen()
 	}
 
 	if (current_click
-		&& (lcd_commands_type != LcdCommands::StopPrint) //click is aborted unless stop print finishes
+		// && (lcd_commands_type != LcdCommands::StopPrint) //click is aborted unless stop print finishes
 		&& ( menu_block_entering_on_serious_errors == SERIOUS_ERR_NONE ) // or a serious error blocks entering the menu
 	)
 	{
@@ -1466,7 +1468,7 @@ void lcd_commands()
 		}
 
 #endif // not SNMM
-
+/* 
 	if (lcd_commands_type == LcdCommands::StopPrint)   /// stop print
 	{
 		
@@ -1558,6 +1560,7 @@ void lcd_commands()
 			lcd_commands_step = 7; 
 		}
 	}
+*/
 
 	if (lcd_commands_type == LcdCommands::FarmModeConfirm)   /// farm mode confirm
 	{
@@ -6051,7 +6054,7 @@ void bowden_menu() {
 	}
 }
 
-//#ifdef SNMM
+#ifdef SNMM
 
 static char snmm_stop_print_menu() { //menu for choosing which filaments will be unloaded in stop print
 	lcd_clear();
@@ -6102,6 +6105,8 @@ static char snmm_stop_print_menu() { //menu for choosing which filaments will be
 	
 }
 
+#endif //SNMM
+
 //! @brief Select one of numbered items
 //!
 //! Create list of items with header. Header can not be selected.
@@ -7320,7 +7325,6 @@ void lcd_print_stop()
 
     // Clear any saved printing state
     cancel_saved_printing();
-	cancel_heatup = true;
 
     // Abort the planner/queue/sd
     planner_abort_hard();
@@ -7331,19 +7335,41 @@ void lcd_print_stop()
 
     CRITICAL_SECTION_END;
 
+#ifdef MESH_BED_LEVELING
+    mbl.active = false; //also prevents undoing the mbl compensation a second time in the second planner_abort_hard()
+#endif
+
 	lcd_setstatuspgm(_T(MSG_PRINT_ABORTED));
 	stoptime = _millis();
 	unsigned long t = (stoptime - starttime - pause_time) / 1000; //time in s
 	pause_time = 0;
 	save_statistics(total_filament_used, t);
-	lcd_return_to_status();
+
-	lcd_ignore_click(true);
+    lcd_commands_step = 0;
-	lcd_commands_step = 0;
+    lcd_commands_type = LcdCommands::Idle;
-	lcd_commands_type = LcdCommands::StopPrint;
+
-	// Turn off the print fan
+    lcd_cooldown(); //turns off heaters and fan; goes to status screen.
-	SET_OUTPUT(FAN_PIN);
+    cancel_heatup = true; //unroll temperature wait loop stack.
-	WRITE(FAN_PIN, 0);
+
-	fanSpeed = 0;
+    current_position[Z_AXIS] += 10; //lift Z.
+    plan_buffer_line_curposXYZE(manual_feedrate[Z_AXIS] / 60, active_extruder);
+
+    if (axis_known_position[X_AXIS] && axis_known_position[Y_AXIS]) //if axis are homed, move to parked position.
+    {
+        current_position[X_AXIS] = X_CANCEL_POS;
+        current_position[Y_AXIS] = Y_CANCEL_POS;
+        plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
+    }
+    st_synchronize();
+
+    if (mmu_enabled) extr_unload(); //M702 C
+
+    finishAndDisableSteppers(); //M84
+
+    lcd_setstatuspgm(_T(WELCOME_MSG));
+    custom_message_type = CustomMsg::Status;
+
+    planner_abort_hard(); //needs to be done since plan_buffer_line resets waiting_inside_plan_buffer_line_print_aborted to false. Also copies current to destination.
 }
 
 void lcd_sdcard_stop()