80cb13003e
Show filename after SD print finished
2024-12-30 13:57:58 +01:00
a9e7f387e8
Replace Set Ready menu entry
...
Replace "Set Ready"/"Set nor Ready" menu entry with "Print from host" entry.
Use "action:start" instead of "action:ready"
2024-08-23 10:24:01 +02:00
3da141b3a7
Remove dead configuration HEATER_BED_DUTY_CYCLE_DIVIDER
...
Setting HEATER_BED_DUTY_CYCLE_DIVIDER has no effect on the firmware
2024-08-15 17:58:07 +00:00
45a223a1f9
Remove White spaces
2024-05-20 19:09:03 +02:00
d5a5835059
Add nozzle change to main menu when QUICK_NOZZLE_CHANGE is defined
...
Add Nozzle diameter to Info screen when printer inactive and QUICK_NOZZLE_CHANGE defined
Solves #4488
2024-01-11 07:36:51 +01:00
59093107fd
Add #ifdef HOST_SHUTDOWN
2024-01-06 00:45:06 +01:00
e5d6d72d23
Add #ifdef
2023-12-15 14:09:46 +01:00
1407f29362
Prevent oozing after filament load
...
Retract 10mm of filament after loading
2023-12-14 14:20:46 +01:00
8b3373b9dc
Raise `END_FILE_SECTION` from 20000 to 30720 to prevent false positive `File incomplete. Continue Anyway?` messages.
2023-11-20 11:23:36 +01:00
a15f536ff4
Combine BED_X/Y() and mbl::get_x/y()
...
flash: -112
2023-08-17 07:52:55 +02:00
842dcc6560
Remove MAX_E_STEPS_PER_UNIT and MIN_E_STEPS_PER_UNIT
...
These constants are not used anywhere so there is no need to rename them
I propose they be removed as cleanup
2023-07-25 17:10:44 +02:00
71180ac284
Cleanup M600 init
...
Instead of removing FILAMENTCHANGE_FINALRETRACT
just set it to 0
No change in memory
2023-05-06 15:24:54 +00:00
8556336185
Fix unload sequence for users without MMU
...
Restores 3.12 sequence which was working well before.
M600 "L" parameter now works like M702 "U" parameter.
Removed a lot of the unused parameters which were copied
from Marlin 2.
Change in memory:
Flash: +96 bytes
2023-05-06 15:24:54 +00:00
b15beb25cc
Remove INVERT_E1_DIR and INVERT_E2_DIR from config
...
I think these should be removed from the configuration files
as these definitions don't do anything.
2023-04-22 15:15:21 +00:00
25522d3d68
Remove unused Autofan extruder configs
2023-04-22 15:15:21 +00:00
fcabcd2804
Remove TEMP_SENSOR_1 and TEMP_SENSOR_2
...
Hopefully I didn't miss anything
2023-04-22 15:15:21 +00:00
f5b9d2ac2e
cleanup: Remove unused Developer define
2023-04-16 13:13:16 +00:00
559e1bb21a
Remove unused MMU configs
...
- MMU_IDLER_SENSOR_ATTEMPTS_NR
- MMU_REQUIRED_FW_BUILDNR
These are no longer used
2023-04-16 13:13:16 +00:00
8f44d1102c
Add PA preheat menu
2022-11-30 06:42:32 +01:00
a256370c39
Remove original marlin fsensor code
2022-09-16 10:17:04 +02:00
3537024ba2
Remove forgotten config in MK2_minirambo_1.0a
2022-08-30 13:57:43 +02:00
8033b65a02
Isolate farm preheat config
2022-08-30 13:57:43 +02:00
d049d09623
Isolate FARM_DEFAULT_SAFETYTIMER_TIME_ms
2022-08-30 13:57:43 +02:00
bef7b086e3
Isolate the entire farm and statistics code
2022-08-30 13:57:43 +02:00
6fc8155cbe
Add n_arc_correction and enhanced small angle sin/cos approximation.
2022-04-28 14:36:51 +02:00
4aa5a75301
Enhance arc interpolation and add M214 for controlling arc interpolation settings.
2022-04-28 14:36:51 +02:00
a617025d85
Move MK2 variants to obsolete
2022-02-25 11:14:55 +01:00
3d-gussner
sarusani
Guðni Már Gilbert
sarusani
Alex Voinea
FormerLurker