8bd84ba4fd
Merge pull request #396 from XPila/MK3
...
Mk3
2018-01-12 22:08:50 +01:00
5ed9233abc
Missed a bit with the last commit.
2018-01-12 22:01:53 +01:00
530dfba417
Status message limit (PFW-124)
2018-01-12 21:21:21 +01:00
82304a2268
Slight optimization of the fan speed interrupt routine by accessing
...
the Arduino millis() without locking interrupts.
2018-01-12 21:16:29 +01:00
ebf6d08fae
Crash detection - message on lcd (PFW-115)
2018-01-12 21:02:49 +01:00
135dda1bff
Slight optimization of the stepper timer routine.
...
Use WRITE_NC instead of WRITE for writing into the slow ports.
2018-01-12 21:01:01 +01:00
3e6d853364
Debugging of the stepper timer routine. When enabled through
...
DEBUG_STEPPER_TIMER_MISSED, the printer is halted on stepper timer overflow
and an error message is displayed.
2018-01-12 20:51:14 +01:00
26747d7236
Definition of 8 pins on the Einsy 0.4 board connected to pin headers
...
to be monitored by an 8 channel logic analyzer, for example the Saleae.
2018-01-12 20:18:20 +01:00
db985065ff
WRITE_NC macro for non-critical (non-synchronized) access to
...
slow ports. The WRITE macro stores the CPU bits on the stack first,
then locks the interupts, reads the port, sets a bit, writes the port
and then finally reverts the CPU bits. The WRITE_NC does not lock
the interrupts, therefore it may only be used where it cannot
be interrupted.
2018-01-12 20:15:59 +01:00
0f46fa0c37
blocking messages in settings/tune menu (PFW104)
...
switch normal/stealth (PFW110)
2018-01-12 19:54:32 +01:00
a4be2af538
commit nr updated
2018-01-11 17:51:30 +01:00
f5ed12817d
Merge pull request #388 from PavelSindler/first_layer_saving
...
Live adjust Z saving using timeout
2018-01-11 17:49:40 +01:00
5c1db284b0
remove setting live adjust status in setup function
2018-01-11 17:48:58 +01:00
97bd56d560
Merge pull request #386 from PavelSindler/selftest_swapped_fans
...
manual check for swapped fans
2018-01-11 17:45:23 +01:00
cfae8f859d
Merge branch 'MK3' into fw_versions
2018-01-11 16:58:47 +01:00
087532085f
development fw versions has initial message for warning
2018-01-11 15:50:26 +01:00
cc20da62a8
whitespace
2018-01-10 23:31:06 +01:00
c185b46eb2
live adjust Z saving using timeout
2018-01-10 23:28:41 +01:00
0d269261e4
PFW-110 - load filament - beep when loading finished.
2018-01-10 18:50:16 +01:00
c79d960cb5
manual check for swapped fans
2018-01-10 16:40:06 +01:00
6ff7641d97
Merge pull request #385 from XPila/MK3
...
Build 143f
2018-01-09 20:01:56 +01:00
43010b30b4
Build 143f
...
Crashdetection improoved, blocking temperature ISR fixed, limits for silent mode adjusted.
2018-01-09 19:54:07 +01:00
858945d949
thermal runaway: reset cmd queue to ensure that heater/bed temp will be always set to zero
2018-01-09 13:35:12 +01:00
75efc71527
temp runaway for heatbed enabled in config
2018-01-08 16:15:50 +01:00
b53197fdd1
Fixed error messages for print fan and extruder fan (were swapped)
2018-01-08 12:07:45 +01:00
0a2087c1cb
build 143e
...
Linear advance disabled
Max feedrate reduced to 200mm/s
Silent max accel reduced to 984mm/s^2
some debug logs removed, tmc_init - log message fixed
2018-01-04 18:08:22 +01:00
8a5ba89a9c
Missing serial characters debuging
...
disabled fan ISR
disabled fsensor ISR
disabled linear advance
build 143b
2018-01-02 20:55:33 +01:00
c6e77f55f6
checkrx in stepper returned back
...
build 143a
2017-12-30 02:55:22 +01:00
568f03c46e
build 143
2017-12-29 23:49:11 +01:00
8d1f2afbf2
build number change
...
just 141r -> 142
2017-12-29 20:22:45 +01:00
0920b62d80
build number change
2017-12-29 20:21:06 +01:00
734639c1da
Unload filament tweak
...
unload filament now has longer and faster slow retract.
2017-12-29 17:53:12 +01:00
7fb1234855
Turn off bed heater after temp calibration
...
After finishing the temperature calibration, turn off the bed heater
right away, before waiting for the user to acknowledge completion.
2017-12-28 23:47:27 -08:00
e3c006dbe9
Serial communication uses port0 or port1, not both, removed some suspected code.
...
build 141
2017-12-29 00:06:47 +01:00
f71f133e80
power panic polished
...
Retraction set correctly to have minimum missing line
Z motor current not lowered that drascialy
Extruder motor turning off instantly
Beeping added to the end
2017-12-28 23:26:06 +01:00
f1c741d027
Filament autoloading improved and minor tweaks
...
Filament autoloading now acts like normal loading (Error message pops out if nozzle too cold, Printer asks if should extrude more when done loading)
Autoloading now unable to turn on when filament sensor is turned off or not responding
Color not right changed to color not correct to avoid slight confusion
2017-12-28 18:59:57 +01:00
26255766f6
Translation fix
...
on -> zap
off -> vyp
2017-12-28 15:55:16 +01:00
5e5588c72c
Text grooming
...
Added language mutations of error messages, menu items.
Synced wording of crash detection in messages.
rPi port -> RPi port.
Minor menu items alignment.
2017-12-28 15:45:52 +01:00
bd58718d9d
dummy "ok" response
...
build 139 (RC4)
2017-12-28 02:45:05 +01:00
e064133a04
Merge remote-tracking branch 'upstream/MK3' into MK3
...
# Please enter a commit message to explain why this merge is necessary,
# especially if it merges an updated upstream into a topic branch.
#
# Lines starting with '#' will be ignored, and an empty message aborts
# the commit.
2017-12-28 01:37:13 +01:00
69d496e157
autoload filament menu (PFW-95, PFW-96)
2017-12-27 21:57:51 +01:00
cbd7f033e8
crashdetection and mode menu (PFW-85, PFW-97)
2017-12-27 21:43:04 +01:00
546314fda7
Removed debug messages from serial comunication (octoprint...).
...
build 137b
2017-12-27 20:29:24 +01:00
f9d5619682
MINTEMP safety for ambient temperature < 18C
...
Silent mode acceleration limit lowered to 1000mm/s^2
2017-12-27 18:20:04 +01:00
a09dee7aea
build 138 (RC3)
2017-12-23 03:44:47 +01:00
23ed33fc21
disable crashdetection while usb printing
2017-12-23 03:42:19 +01:00
8739b4a610
MINTEMP fix
2017-12-23 03:36:08 +01:00
1a69c979bf
Increase Z current (PFW-90).
2017-12-23 01:01:57 +01:00
8f7a50cfcd
Merge pull request #343 from PavelSindler/m110_fix
...
M110 fix
2017-12-23 00:04:11 +01:00
e8477b525c
initial version of M110 fix (port from MK2)
2017-12-22 22:34:57 +01:00
PavelSindler
bubnikv
Robert Pelnar
PavelSindler
Michal Průša
Phil Dubach