aee62750e7
Build 109
2017-11-16 22:03:36 +01:00
279ea79bf6
Merge pull request #86 from PavelSindler/keepalive_messages
...
host keep alive messages
2017-11-16 20:53:09 +01:00
2a85de48ea
Merge pull request #88 from XPila/MK3
...
Mk3
2017-11-16 20:52:46 +01:00
ee2f927148
Build Number = 108
...
FSensor log can be enabled with D9125L1
Selftest menu
PINDA D codes
2017-11-16 20:51:50 +01:00
16a7adfe33
merging with upstream
2017-11-15 15:45:26 +01:00
91d125369e
keepalive messages initial version
2017-11-15 15:09:29 +01:00
19d89b37b5
Merge pull request #83 from PavelSindler/lin_adv_fix
...
Lin adv. fix from MK2 fw
2017-11-15 11:53:39 +01:00
9e2533ecdf
Support menu translated and fixes, snmm M600 long beep fix
2017-11-14 16:10:10 +01:00
4d9780a3c6
Merged lin adv. fix from MK2
2017-11-14 13:57:32 +01:00
dfe3541d2b
Merge branch 'MK3' into MK3
2017-11-13 18:48:19 +01:00
01de834e0d
SG_THR_X = 2, holding currents == running currents
...
Farm preheat menu
dcode D5 - read/write/erase FLASH
dcode D6 - bootloader update test (for new stk500-prusa)
_NO_ASM - MINGW simulator support
fixed bug - "Fil. sensor [on/off]" menu
Build number = 107
2017-11-13 18:45:11 +01:00
eda0c6bd39
english version of xyz: place/remove steel sheet; wait for cooling down removed,
2017-11-13 17:09:26 +01:00
5707f8b14e
Merge remote-tracking branch 'upstream/MK3' into wizard
2017-11-13 14:39:14 +01:00
fbbcc27f1a
X max lowered to 250, XYZ/Z calibration: Z top coordinate changed, changes in xyz cal. because of stell sheet, still not final version
2017-11-12 11:30:06 +01:00
55325a5a32
Merge branch 'MK3' into MK3
2017-11-07 17:15:27 +01:00
2e68770e62
initial version - messages missing (will not compile)
2017-11-07 16:49:04 +01:00
c36b7be90c
SUPPORT_VERBOSITY initial version
2017-11-07 11:36:41 +01:00
461675b806
Merge pull request #78 from PavelSindler/4point_xyz_cal
...
4point xyz cal.
2017-11-07 10:02:32 +01:00
967594edf0
Added G-CODE "PRUSA FAN" to report RPM of both fans
2017-11-03 20:27:52 +01:00
877c8a3978
TMC2130 configuration in eeprom (not finished).
...
Extruder and Z holding currents same as running currents.
M600 filament unload speed = 3500 (PFW-22).
FSensor - algorithm changed (reset error couter instead of decrement)
build number = 106
2017-10-30 15:45:29 +01:00
1ee6016fa0
Merge remote-tracking branch 'upstream/MK3' into 4point_xyz_cal
2017-10-30 11:48:45 +01:00
bd7c3d08f3
Marlin_main - lineending CRLF -> LF
2017-10-27 17:07:02 +02:00
c4d7b801b9
Initial version. XYZ cal works, but bed ref. points coordinates must be checked.
2017-10-27 16:12:37 +02:00
d37c925bc0
Merge branch 'MK3' into print_fan_speed
2017-10-26 18:04:38 +02:00
f4d5d891df
measuring pulse width: initial version
2017-10-26 17:42:27 +02:00
cddb0eafb8
PAT9125 - sampled only Y value, new debug code D9125.
...
FSensor - synchronous sampling and new algorithm
build number = 103
2017-10-24 19:45:15 +02:00
8734961e0e
M114 now reports also actual extruder position,
...
PAT9125 HWI2C (Wire) support,
fsensor implementation into separate file
build number = 102
2017-10-22 22:42:45 +02:00
c3585bc696
Automatic recovery typo fix
...
Failures statistics in eeprom
2017-09-26 14:14:17 +01:00
5ff28682be
Automatic recovery after crash is detected
2017-09-26 11:48:46 +01:00
b475d11bdb
Maker Faire brainstorm 2.0 (2)
...
Automatic recover after short power loss (according to heatbed temperature drop)
Adjusted crashdetection - TMC2130_TCOOLTHRS_X and TMC2130_TCOOLTHRS_Y = 450 to be enabled at low speed
!!!ALL FEATURES TESTED AT THIS POINT!!!
2017-09-26 06:11:42 +02:00
89121e6e34
Maker Faire brainstorm 2.0
...
Added filament sensor and crash detection to EEPROM
Added crash-detection counters display disable directive
Added Restore/Save print directive
Added crash detection and filament sensor settings to Tune menu
2017-09-26 04:30:10 +02:00
73cc1c9c8a
initial state of crash detect and filament sensor is ON
...
slowed down return speed from crash detect after home
Added babystep apply after return from crash detect (don’t know if it’s accurate)
Added D10 to set machine to XYZ correctly calibrated
Added resume debug directive to mask additional menu item
2017-09-26 03:21:33 +02:00
39f6e746dc
Crashdetection tunning.
2017-09-26 01:43:56 +02:00
c6e9896257
Changed the homing routine to avoid crashing into the right end stop.
2017-09-25 15:20:39 +02:00
b0ca2477c8
Modified homing procedures for the X & Y axes using the Trinamic stall guard
...
to run against the end stop with a repeatable velocity.
Slightly reduced the collision detection sensitivity.
2017-09-24 00:07:32 +02:00
b58dcf33d0
Removed a test snippet, which broke the power panic recovery.
2017-09-23 20:52:22 +02:00
f2f74ebddf
Powerpanic Z correction improved.
2017-09-23 20:36:10 +02:00
e11ae8bdbf
Soft homing + fixed homing in silent mode.
2017-09-23 20:01:37 +02:00
480838a0a1
Fixed homing (mbl and babystep - crashdetection recovery work fine now).
2017-09-23 16:35:01 +02:00
89acf29247
Silent/High Power mode switching with crashdetection.
2017-09-23 15:01:31 +02:00
d2ff47dac8
Crashdetection
2017-09-22 23:06:52 +02:00
df1aa85526
Crashdetection + configuration file.
2017-09-22 19:28:32 +02:00
522b438ef5
Power panic: When panicking, move the X carriage to the bed side fast.
2017-09-22 16:44:00 +02:00
a8297369b2
Merge branch 'MK3' of https://github.com/prusa3d/Prusa-Firmware-DEV into MK3
2017-09-22 15:43:56 +02:00
23b4fa6c0d
Some fixes / improvements of the power panic:
...
1) Fix of an order of SD card function calls on recover: First set position, then restart the print.
2) Some convenience improvements: On panic, the X axis moves to the edge to avoid oozing into the print.
3) On recovery, move Z up if the head is too low to make it easier for the user to clean the print head.
2017-09-22 15:43:39 +02:00
37d7740e42
Merge pull request #47 from PavelSindler/MK3
...
fan check turn off, saving to eeprom with offset and levels, fan kickstart,2nd heatbed version, fans check modified
2017-09-22 14:39:52 +02:00
72ab17f585
Further fixes of the power panic and g-code & planner queues.
2017-09-22 13:44:10 +02:00
6eb57da770
fan check can be turned off from support menu, saving parameters to eeprom with offset and different levels, fan kickstart,2nd heatbed version, fans check modified
2017-09-21 15:20:02 +02:00
1409bd633c
Power Panic - new method of sd_position calculation.
2017-09-21 05:35:41 +02:00
9b901bd3f5
XY homing repeatibility - move by 160um from margin.
2017-09-21 04:55:30 +02:00
Robert Pelnar
PavelSindler
PavelSindler
michalprusa
bubnikv