374 lines
14 KiB
C
374 lines
14 KiB
C
#ifndef CONFIGURATION_H
|
|
#define CONFIGURATION_H
|
|
|
|
#include <stdint.h>
|
|
#include "boards.h"
|
|
|
|
#define STR_HELPER(x) #x
|
|
#define STR(x) STR_HELPER(x)
|
|
#define _CONCAT(x,y) x##y
|
|
#define CONCAT(x,y) _CONCAT(x,y)
|
|
|
|
#include <avr/pgmspace.h>
|
|
extern const uint16_t _nPrinterType;
|
|
extern const char _sPrinterName[] PROGMEM;
|
|
extern const uint16_t _nPrinterMmuType;
|
|
extern const char _sPrinterMmuName[] PROGMEM;
|
|
|
|
// Firmware version.
|
|
// NOTE: These are ONLY used if you are not building via cmake and/or not in a git repository.
|
|
// Otherwise the repository information takes precedence.
|
|
#ifndef CMAKE_CONTROL
|
|
#define FW_MAJOR 3
|
|
#define FW_MINOR 14
|
|
#define FW_REVISION 0
|
|
#define FW_COMMITNR 7945
|
|
#define FW_FLAVOR BETA //uncomment if DEV, ALPHA, BETA or RC
|
|
#define FW_FLAVERSION 1 //uncomment if FW_FLAVOR is defined and versioning is needed. Limited to max 8.
|
|
#endif
|
|
|
|
#ifndef FW_FLAVOR
|
|
#define FW_TWEAK (FIRMWARE_REVISION_RELEASED)
|
|
#define FW_VERSION STR(FW_MAJOR) "." STR(FW_MINOR) "." STR(FW_REVISION)
|
|
#define FW_VERSION_FULL STR(FW_MAJOR) "." STR(FW_MINOR) "." STR(FW_REVISION) "-" STR(FW_COMMITNR)
|
|
#else
|
|
// Construct the TWEAK value as it is expected from the enum.
|
|
#define FW_TWEAK (CONCAT(FIRMWARE_REVISION_,FW_FLAVOR) + FW_FLAVERSION)
|
|
#define FW_VERSION STR(FW_MAJOR) "." STR(FW_MINOR) "." STR(FW_REVISION) "-" STR(FW_FLAVOR) "" STR(FW_FLAVERSION)
|
|
#define FW_VERSION_FULL STR(FW_MAJOR) "." STR(FW_MINOR) "." STR(FW_REVISION) "-" STR(FW_FLAVOR) "" STR(FW_FLAVERSION) "+" STR(FW_COMMITNR)
|
|
#endif
|
|
|
|
// The full version string and repository source are set via cmake
|
|
#ifndef CMAKE_CONTROL
|
|
#define FW_COMMIT_HASH_LENGTH 1
|
|
#define FW_COMMIT_HASH "0"
|
|
#define FW_REPOSITORY "Unknown"
|
|
#endif
|
|
|
|
// G-code language level
|
|
#define GCODE_LEVEL 1
|
|
|
|
#ifndef SOURCE_DATE_EPOCH
|
|
#define SOURCE_DATE_EPOCH __DATE__
|
|
#endif
|
|
#ifndef SOURCE_TIME_EPOCH
|
|
#define SOURCE_TIME_EPOCH __TIME__
|
|
#endif
|
|
|
|
#include "Configuration_var.h"
|
|
|
|
#define FW_PRUSA3D_MAGIC "PRUSA3DFW"
|
|
#define FW_PRUSA3D_MAGIC_LEN 10
|
|
|
|
#include "eeprom.h"
|
|
|
|
// This configuration file contains the basic settings.
|
|
// Advanced settings can be found in Configuration_adv.h
|
|
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
|
|
|
|
// User-specified version info of this build to display in [Pronterface, etc] terminal window during
|
|
// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
|
|
// build by the user have been successfully uploaded into firmware.
|
|
|
|
#define STRING_VERSION_CONFIG_H SOURCE_DATE_EPOCH " " SOURCE_TIME_EPOCH // build date and time
|
|
#define STRING_CONFIG_H_AUTHOR FW_REPOSITORY // Who made the changes.
|
|
|
|
// SERIAL_PORT selects which serial port should be used for communication with the host.
|
|
// This allows the connection of wireless adapters (for instance) to non-default port pins.
|
|
// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
|
|
#define SERIAL_PORT 0
|
|
|
|
// This determines the communication speed of the printer
|
|
#define BAUDRATE 115200
|
|
|
|
// Enable g-code compression (see https://github.com/scottmudge/OctoPrint-MeatPack)
|
|
#define ENABLE_MEATPACK
|
|
|
|
// This enables the serial port associated to the Bluetooth interface
|
|
//#define BTENABLED // Enable BT interface on AT90USB devices
|
|
|
|
// The following define selects which electronics board you have.
|
|
// Please choose the name from boards.h that matches your setup
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
|
|
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
|
// #define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
|
|
|
// This defines the number of extruders
|
|
#define EXTRUDERS 1
|
|
|
|
//// The following define selects which power supply you have. Please choose the one that matches your setup
|
|
// 1 = ATX
|
|
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
|
|
|
|
#define POWER_SUPPLY 1
|
|
|
|
|
|
|
|
|
|
|
|
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
|
// #define PS_DEFAULT_OFF
|
|
|
|
|
|
// Actual temperature must be close to target for this long before M109 returns success
|
|
#define TEMP_RESIDENCY_TIME 3 // (seconds)
|
|
#define TEMP_HYSTERESIS 5 // (degC) range of +/- temperatures considered "close" to the target one
|
|
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
|
|
|
|
// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS
|
|
//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R
|
|
//#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R
|
|
|
|
// PID settings:
|
|
// Comment the following line to disable PID and enable bang-bang.
|
|
#define PIDTEMP
|
|
#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
|
|
#define PID_MAX BANG_MAX // limits current to nozzle while PID is active; 255=full current
|
|
#ifdef PIDTEMP
|
|
//#define PID_DEBUG // Sends debug data to the serial port.
|
|
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
|
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
|
#define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
|
|
#define PID_K1 0.95 //smoothing factor within the PID
|
|
#define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
|
|
|
|
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
|
// Ultimaker
|
|
|
|
|
|
// MakerGear
|
|
// #define DEFAULT_Kp 7.0
|
|
// #define DEFAULT_Ki 0.1
|
|
// #define DEFAULT_Kd 12
|
|
|
|
// Mendel Parts V9 on 12V
|
|
// #define DEFAULT_Kp 63.0
|
|
// #define DEFAULT_Ki 2.25
|
|
// #define DEFAULT_Kd 440
|
|
#endif // PIDTEMP
|
|
|
|
|
|
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
|
|
//can be software-disabled for whatever purposes by
|
|
#define PREVENT_DANGEROUS_EXTRUDE
|
|
//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
|
|
#define PREVENT_LENGTHY_EXTRUDE
|
|
|
|
#ifdef DEBUG_DISABLE_PREVENT_EXTRUDER
|
|
#undef PREVENT_DANGEROUS_EXTRUDE
|
|
#undef PREVENT_LENGTHY_EXTRUDE
|
|
#endif //DEBUG_DISABLE_PREVENT_EXTRUDER
|
|
|
|
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
|
|
|
|
/*================== Thermal Runaway Protection ==============================
|
|
This is a feature to protect your printer from burn up in flames if it has
|
|
a thermistor coming off place (this happened to a friend of mine recently and
|
|
motivated me writing this feature).
|
|
|
|
The issue: If a thermistor come off, it will read a lower temperature than actual.
|
|
The system will turn the heater on forever, burning up the filament and anything
|
|
else around.
|
|
|
|
After the temperature reaches the target for the first time, this feature will
|
|
start measuring for how long the current temperature stays below the target
|
|
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS).
|
|
|
|
If it stays longer than _PERIOD, it means the thermistor temperature
|
|
cannot catch up with the target, so something *may be* wrong. Then, to be on the
|
|
safe side, the system will he halt.
|
|
|
|
Bear in mind the count down will just start AFTER the first time the
|
|
thermistor temperature is over the target, so you will have no problem if
|
|
your extruder heater takes 2 minutes to hit the target on heating.
|
|
|
|
*/
|
|
// If you want to enable this feature for all your extruder heaters,
|
|
// uncomment the 2 defines below:
|
|
|
|
// Parameters for all extruder heaters
|
|
//#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds
|
|
//#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
|
|
|
|
// If you want to enable this feature for your bed heater,
|
|
// uncomment the 2 defines below:
|
|
|
|
// Parameters for the bed heater
|
|
//#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
|
|
//#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
|
|
//===========================================================================
|
|
|
|
|
|
//===========================================================================
|
|
//=============================Mechanical Settings===========================
|
|
//===========================================================================
|
|
|
|
// Uncomment the following line to enable CoreXY kinematics
|
|
// #define COREXY
|
|
|
|
// coarse Endstop Settings
|
|
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
|
|
|
#ifndef ENDSTOPPULLUPS
|
|
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
|
|
// #define ENDSTOPPULLUP_XMAX
|
|
// #define ENDSTOPPULLUP_YMAX
|
|
// #define ENDSTOPPULLUP_ZMAX
|
|
// #define ENDSTOPPULLUP_XMIN
|
|
// #define ENDSTOPPULLUP_YMIN
|
|
// #define ENDSTOPPULLUP_ZMIN
|
|
#endif
|
|
|
|
#ifdef ENDSTOPPULLUPS
|
|
#define ENDSTOPPULLUP_XMAX
|
|
#define ENDSTOPPULLUP_YMAX
|
|
#define ENDSTOPPULLUP_ZMAX
|
|
#define ENDSTOPPULLUP_XMIN
|
|
#define ENDSTOPPULLUP_YMIN
|
|
#define ENDSTOPPULLUP_ZMIN
|
|
#endif
|
|
|
|
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
|
|
|
|
#define X_MAX_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop.
|
|
#define Y_MAX_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop.
|
|
#define Z_MAX_ENDSTOP_INVERTING 1 // set to 1 to invert the logic of the endstop.
|
|
//#define DISABLE_MAX_ENDSTOPS
|
|
//#define DISABLE_MIN_ENDSTOPS
|
|
|
|
// Disable max endstops for compatibility with endstop checking routine
|
|
#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
|
|
#define DISABLE_MAX_ENDSTOPS
|
|
#endif
|
|
|
|
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
|
#define X_ENABLE_ON 0
|
|
#define Y_ENABLE_ON 0
|
|
#define Z_ENABLE_ON 0
|
|
#define E_ENABLE_ON 0 // For all extruders
|
|
|
|
// Disables axis when it's not being used.
|
|
#define DISABLE_X 0
|
|
#define DISABLE_Y 0
|
|
#define DISABLE_Z 0
|
|
#define DISABLE_E 0// For all extruders
|
|
|
|
|
|
// ENDSTOP SETTINGS:
|
|
// Sets direction of endstops when homing; 1=MAX, -1=MIN
|
|
#define X_HOME_DIR -1
|
|
#define Y_HOME_DIR -1
|
|
#define Z_HOME_DIR -1
|
|
|
|
#ifdef DEBUG_DISABLE_SWLIMITS
|
|
#define min_software_endstops 0
|
|
#define max_software_endstops 0
|
|
#else
|
|
#define min_software_endstops 1 // If true, axis won't move to coordinates less than HOME_POS.
|
|
#define max_software_endstops 1 // If true, axis won't move to coordinates greater than the defined lengths below.
|
|
#endif //DEBUG_DISABLE_SWLIMITS
|
|
|
|
|
|
#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
|
|
#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
|
|
#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
|
|
|
|
#define Z_HEIGHT_HIDE_LIVE_ADJUST_MENU 2.0f
|
|
|
|
#define HOME_Z_SEARCH_THRESHOLD 0.15f // Threshold of the Z height in calibration
|
|
|
|
// The position of the homing switches
|
|
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
|
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
|
|
|
//Manual homing switch locations:
|
|
// For deltabots this means top and center of the Cartesian print volume.
|
|
|
|
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
|
#define DEFAULT_XJERK 10 // (mm/sec)
|
|
#define DEFAULT_YJERK 10 // (mm/sec)
|
|
#define DEFAULT_ZJERK 0.4 // (mm/sec)
|
|
#define DEFAULT_EJERK 4.5 // (mm/sec)
|
|
|
|
//===========================================================================
|
|
//=============================Additional Features===========================
|
|
//===========================================================================
|
|
|
|
// Custom M code points
|
|
#define CUSTOM_M_CODES
|
|
|
|
|
|
// Host Keepalive
|
|
//
|
|
// When enabled Marlin will send a busy status message to the host
|
|
// every couple of seconds when it can't accept commands.
|
|
//
|
|
#ifndef HEATBED_ANALYSIS
|
|
#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
|
|
#endif //HEATBED_ANALYSIS
|
|
#define HOST_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
|
|
|
|
//LCD and SD support
|
|
#define SDSUPPORT // Enable SD Card Support in Hardware Console
|
|
//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
|
|
#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
|
|
#define ENCODER_PULSES_PER_STEP 4 // Increase if you have a high resolution encoder
|
|
//#define ENCODER_STEPS_PER_MENU_ITEM 1 // Set according to ENCODER_PULSES_PER_STEP or your liking
|
|
|
|
// The RepRapDiscount Smart Controller (white PCB)
|
|
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
|
|
#define REPRAP_DISCOUNT_SMART_CONTROLLER
|
|
#define SDSUPPORT
|
|
#define LCD_WIDTH 20
|
|
#define LCD_HEIGHT 4
|
|
|
|
|
|
// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
|
//#define FAST_PWM_FAN
|
|
|
|
// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
|
|
// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
|
|
// is too low, you should also increment SOFT_PWM_SCALE.
|
|
#define FAN_SOFT_PWM
|
|
#define FAN_SOFT_PWM_BITS 4 //PWM bit resolution = 4bits, freq = 62.5Hz
|
|
|
|
// Bed soft pwm
|
|
#define HEATER_BED_SOFT_PWM_BITS 5 //PWM bit resolution = 5bits, freq = 31.25Hz
|
|
|
|
// Incrementing this by 1 will double the software PWM frequency,
|
|
// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
|
|
// However, control resolution will be halved for each increment;
|
|
// at zero value, there are 128 effective control positions.
|
|
#define SOFT_PWM_SCALE 0
|
|
|
|
// M240 Triggers a camera by emulating a Canon RC-1 Remote
|
|
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
|
|
// #define PHOTOGRAPH_PIN 23
|
|
|
|
// SF send wrong arc g-codes when using Arc Point as fillet procedure
|
|
//#define SF_ARC_FIX
|
|
|
|
//define BlinkM/CyzRgb Support
|
|
//#define BLINKM
|
|
|
|
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm). Used by the volumetric extrusion.
|
|
|
|
// Try to maintain a minimum distance from the bed even when Z is
|
|
// unknown when doing the following operations
|
|
#define MIN_Z_FOR_LOAD 50 // lcd filament loading or autoload
|
|
#define MIN_Z_FOR_UNLOAD 20 // lcd filament unloading
|
|
#define MIN_Z_FOR_SWAP 27 // filament change (including M600)
|
|
#define MIN_Z_FOR_PREHEAT 10 // lcd preheat
|
|
|
|
#include "Configuration_adv.h"
|
|
#include "thermistortables.h"
|
|
|
|
#endif //__CONFIGURATION_H
|