josh
/
Teacup_Firmware
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

Add support for USB serial using the LUFA library. 

Configured for at90usb1287 and F_CPU=8000000L this is compatible with
the AT90USBKEY.  Other boards, chips and frequencies require updating
the configuration in lufa_serial/makefile and possibly adding a Board
driver to the LUFA submodule.
This commit is contained in:
Ben Jackson 2011-03-04 14:56:27 -08:00 committed by Michael Moon
parent c304c300b7
commit 08b516d7f3
9 changed files with 1528 additions and 4 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

33
Makefile
View File

@ -33,8 +33,10 @@
# MCU_TARGET = atmega328p
MCU_TARGET = atmega644p
# MCU_TARGET = atmega1280
# MCU_TARGET = at90usb1287
# F_CPU = 16000000L
# F_CPU = 8000000L
##############################################################################
# #
@ -96,7 +98,7 @@ PROGBAUD = 57600
PROGRAM = mendel
SOURCES = $(PROGRAM).c serial.c dda.c gcode_parse.c gcode_process.c timer.c temp.c sermsg.c dda_queue.c watchdog.c debug.c sersendf.c heater.c analog.c delay.c intercom.c pinio.c clock.c home.c crc.c
SOURCES = $(PROGRAM).c dda.c gcode_parse.c gcode_process.c timer.c temp.c sermsg.c dda_queue.c watchdog.c debug.c sersendf.c heater.c analog.c delay.c intercom.c pinio.c clock.c home.c crc.c
ARCH = avr-
CC = $(ARCH)gcc
@ -108,13 +110,31 @@ OPTIMIZE = -Os -ffunction-sections -finline-functions-called-once -mcall-prologu
CFLAGS = -g -Wall -Wstrict-prototypes $(OPTIMIZE) -mmcu=$(MCU_TARGET) $(DEFS) -std=gnu99 -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums -save-temps
LDFLAGS = -Wl,--as-needed -Wl,--gc-sections
LIBS = -lm
LIBDEPS =
SUBDIRS =
ifneq (,$(findstring usb,$(MCU_TARGET)))
LDFLAGS += -Llufa_serial
LIBS += -llufa_serial
SUBDIRS += lufa_serial
LIBDEPS += lufa_serial/liblufa_serial.a
else
SOURCES += serial.c
endif
OBJ = $(patsubst %.c,%.o,${SOURCES})
.PHONY: all program clean size
.PHONY: all program clean size subdirs
.PRECIOUS: %.o %.elf
all: config.h $(PROGRAM).hex $(PROGRAM).lst $(PROGRAM).sym size
all: config.h subdirs $(PROGRAM).hex $(PROGRAM).lst $(PROGRAM).sym size
$(PROGRAM).elf: $(LIBDEPS)
subdirs:
@for dir in $(SUBDIRS); do \
$(MAKE) -C $$dir; \
done
program: $(PROGRAM).hex config.h
stty $(PROGBAUD) raw ignbrk hup < $(PROGPORT)
@ -131,9 +151,14 @@ program-fuses:
$(AVRDUDE) -cstk500v1 -b$(PROGBAUD) -p$(MCU_TARGET) -P$(PROGPORT) -C$(AVRDUDECONF) -U hfuse:w:hfuse
$(AVRDUDE) -cstk500v1 -b$(PROGBAUD) -p$(MCU_TARGET) -P$(PROGPORT) -C$(AVRDUDECONF) -U efuse:w:efuse
clean:
clean: clean-subdirs
rm -rf *.o *.elf *.lst *.map *.sym *.lss *.eep *.srec *.bin *.hex *.al *.i *.s *~ *fuse
clean-subdirs:
@for dir in $(SUBDIRS); do \
$(MAKE) -C $$dir clean; \
done
size: $(PROGRAM).elf
@echo " SIZE Atmega168 Atmega328p Atmega644"
@$(OBJDUMP) -h $^ | perl -MPOSIX -ne '/.(text)\s+([0-9a-f]+)/ && do { $$a += eval "0x$$2" }; END { printf " FLASH : %5d bytes (%2d%% of %2dkb) (%2d%% of %2dkb) (%2d%% of %2dkb)\n", $$a, ceil($$a * 100 / (15 * 1024)), 15, ceil($$a * 100 / (31 * 1024)), 31, ceil($$a * 100 / (63 * 1024)), 63 }'

3
README
View File

@ -5,6 +5,7 @@ Rewrite of Reprap Mendel firmware:
* can fit onto atmega168 depending on selected options
* works on atmega328p
* works on atmega644p
* works on at90usb1287 with direct USB serial
* porting to atmega1280 in progress
* will work on larger atmegas with minor porting
@ -20,6 +21,8 @@ patches, issues go here
# #
##############################################################################
0) If using USB serial via LUFA, fetch the submodule with:
git submodule init; git submodule update
1) COPY config.YOURBOARDHERE.h to config.h and edit to suit your electronics
2) check programming settings in Makefile (chip type, avrdude settings, etc)
3) make

2
lufa_serial/.gitignore vendored Normal file
View File

@ -0,0 +1,2 @@
.dep/
*.a

278
lufa_serial/Descriptors.c Normal file
View File

@ -0,0 +1,278 @@
/*
* This implementation of a serial.c-like interface for the Teacup firmware
* is based on LUFA/Demos/Device/LowLevel/VirtualSerial.
*
* Modifications by Ben Jackson <ben@ben.com> under GPLv2
*/
/*
LUFA Library
Copyright (C) Dean Camera, 2010.
dean [at] fourwalledcubicle [dot] com
www.lufa-lib.org
*/
/*
Copyright 2010 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby granted
without fee, provided that the above copyright notice appear in
all copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* USB Device Descriptors, for library use when in USB device mode. Descriptors are special
* computer-readable structures which the host requests upon device enumeration, to determine
* the device's capabilities and functions.
*/
#include "Descriptors.h"
/* On some devices, there is a factory set internal serial number which can be automatically sent to the host as
* the device's serial number when the Device Descriptor's .SerialNumStrIndex entry is set to USE_INTERNAL_SERIAL.
* This allows the host to track a device across insertions on different ports, allowing them to retain allocated
* resources like COM port numbers and drivers. On demos using this feature, give a warning on unsupported devices
* so that the user can supply their own serial number descriptor instead or remove the USE_INTERNAL_SERIAL value
* from the Device Descriptor (forcing the host to generate a serial number for each device from the VID, PID and
* port location).
*/
#if (USE_INTERNAL_SERIAL == NO_DESCRIPTOR)
#warning USE_INTERNAL_SERIAL is not available on this AVR - please manually construct a device serial descriptor.
#endif
/** Device descriptor structure. This descriptor, located in FLASH memory, describes the overall
* device characteristics, including the supported USB version, control endpoint size and the
* number of device configurations. The descriptor is read out by the USB host when the enumeration
* process begins.
*/
USB_Descriptor_Device_t PROGMEM DeviceDescriptor =
{
.Header = {.Size = sizeof(USB_Descriptor_Device_t), .Type = DTYPE_Device},
.USBSpecification = VERSION_BCD(01.10),
.Class = CDC_CSCP_CDCClass,
.SubClass = CDC_CSCP_NoSpecificSubclass,
.Protocol = CDC_CSCP_NoSpecificProtocol,
.Endpoint0Size = FIXED_CONTROL_ENDPOINT_SIZE,
.VendorID = 0x03EB,
.ProductID = 0x2044,
.ReleaseNumber = VERSION_BCD(00.01),
.ManufacturerStrIndex = 0x01,
.ProductStrIndex = 0x02,
.SerialNumStrIndex = USE_INTERNAL_SERIAL,
.NumberOfConfigurations = FIXED_NUM_CONFIGURATIONS
};
/** Configuration descriptor structure. This descriptor, located in FLASH memory, describes the usage
* of the device in one of its supported configurations, including information about any device interfaces
* and endpoints. The descriptor is read out by the USB host during the enumeration process when selecting
* a configuration so that the host may correctly communicate with the USB device.
*/
USB_Descriptor_Configuration_t PROGMEM ConfigurationDescriptor =
{
.Config =
{
.Header = {.Size = sizeof(USB_Descriptor_Configuration_Header_t), .Type = DTYPE_Configuration},
.TotalConfigurationSize = sizeof(USB_Descriptor_Configuration_t),
.TotalInterfaces = 2,
.ConfigurationNumber = 1,
.ConfigurationStrIndex = NO_DESCRIPTOR,
.ConfigAttributes = (USB_CONFIG_ATTR_BUSPOWERED | USB_CONFIG_ATTR_SELFPOWERED),
.MaxPowerConsumption = USB_CONFIG_POWER_MA(100)
},
.CDC_CCI_Interface =
{
.Header = {.Size = sizeof(USB_Descriptor_Interface_t), .Type = DTYPE_Interface},
.InterfaceNumber = 0,
.AlternateSetting = 0,
.TotalEndpoints = 1,
.Class = CDC_CSCP_CDCClass,
.SubClass = CDC_CSCP_ACMSubclass,
.Protocol = CDC_CSCP_ATCommandProtocol,
.InterfaceStrIndex = NO_DESCRIPTOR
},
.CDC_Functional_Header =
{
.Header = {.Size = sizeof(USB_CDC_Descriptor_FunctionalHeader_t), .Type = DTYPE_CSInterface},
.Subtype = CDC_DSUBTYPE_CSInterface_Header,
.CDCSpecification = VERSION_BCD(01.10),
},
.CDC_Functional_ACM =
{
.Header = {.Size = sizeof(USB_CDC_Descriptor_FunctionalACM_t), .Type = DTYPE_CSInterface},
.Subtype = CDC_DSUBTYPE_CSInterface_ACM,
.Capabilities = 0x06,
},
.CDC_Functional_Union =
{
.Header = {.Size = sizeof(USB_CDC_Descriptor_FunctionalUnion_t), .Type = DTYPE_CSInterface},
.Subtype = CDC_DSUBTYPE_CSInterface_Union,
.MasterInterfaceNumber = 0,
.SlaveInterfaceNumber = 1,
},
.CDC_NotificationEndpoint =
{
.Header = {.Size = sizeof(USB_Descriptor_Endpoint_t), .Type = DTYPE_Endpoint},
.EndpointAddress = (ENDPOINT_DESCRIPTOR_DIR_IN | CDC_NOTIFICATION_EPNUM),
.Attributes = (EP_TYPE_INTERRUPT | ENDPOINT_ATTR_NO_SYNC | ENDPOINT_USAGE_DATA),
.EndpointSize = CDC_NOTIFICATION_EPSIZE,
.PollingIntervalMS = 0xFF
},
.CDC_DCI_Interface =
{
.Header = {.Size = sizeof(USB_Descriptor_Interface_t), .Type = DTYPE_Interface},
.InterfaceNumber = 1,
.AlternateSetting = 0,
.TotalEndpoints = 2,
.Class = CDC_CSCP_CDCDataClass,
.SubClass = CDC_CSCP_NoDataSubclass,
.Protocol = CDC_CSCP_NoDataProtocol,
.InterfaceStrIndex = NO_DESCRIPTOR
},
.CDC_DataOutEndpoint =
{
.Header = {.Size = sizeof(USB_Descriptor_Endpoint_t), .Type = DTYPE_Endpoint},
.EndpointAddress = (ENDPOINT_DESCRIPTOR_DIR_OUT | CDC_RX_EPNUM),
.Attributes = (EP_TYPE_BULK | ENDPOINT_ATTR_NO_SYNC | ENDPOINT_USAGE_DATA),
.EndpointSize = CDC_TXRX_EPSIZE,
.PollingIntervalMS = 0x01
},
.CDC_DataInEndpoint =
{
.Header = {.Size = sizeof(USB_Descriptor_Endpoint_t), .Type = DTYPE_Endpoint},
.EndpointAddress = (ENDPOINT_DESCRIPTOR_DIR_IN | CDC_TX_EPNUM),
.Attributes = (EP_TYPE_BULK | ENDPOINT_ATTR_NO_SYNC | ENDPOINT_USAGE_DATA),
.EndpointSize = CDC_TXRX_EPSIZE,
.PollingIntervalMS = 0x01
}
};
/** Language descriptor structure. This descriptor, located in FLASH memory, is returned when the host requests
* the string descriptor with index 0 (the first index). It is actually an array of 16-bit integers, which indicate
* via the language ID table available at USB.org what languages the device supports for its string descriptors.
*/
USB_Descriptor_String_t PROGMEM LanguageString =
{
.Header = {.Size = USB_STRING_LEN(1), .Type = DTYPE_String},
.UnicodeString = {LANGUAGE_ID_ENG}
};
/** Manufacturer descriptor string. This is a Unicode string containing the manufacturer's details in human readable
* form, and is read out upon request by the host when the appropriate string ID is requested, listed in the Device
* Descriptor.
*/
USB_Descriptor_String_t PROGMEM ManufacturerString =
{
.Header = {.Size = USB_STRING_LEN(6), .Type = DTYPE_String},
.UnicodeString = L"Reprap"
};
/** Product descriptor string. This is a Unicode string containing the product's details in human readable form,
* and is read out upon request by the host when the appropriate string ID is requested, listed in the Device
* Descriptor.
*/
USB_Descriptor_String_t PROGMEM ProductString =
{
.Header = {.Size = USB_STRING_LEN(13), .Type = DTYPE_String},
.UnicodeString = L"Teacup Reprap"
};
/** This function is called by the library when in device mode, and must be overridden (see library "USB Descriptors"
* documentation) by the application code so that the address and size of a requested descriptor can be given
* to the USB library. When the device receives a Get Descriptor request on the control endpoint, this function
* is called so that the descriptor details can be passed back and the appropriate descriptor sent back to the
* USB host.
*/
uint16_t CALLBACK_USB_GetDescriptor(const uint16_t wValue,
const uint8_t wIndex,
const void** const DescriptorAddress)
{
const uint8_t DescriptorType = (wValue >> 8);
const uint8_t DescriptorNumber = (wValue & 0xFF);
const void* Address = NULL;
uint16_t Size = NO_DESCRIPTOR;
switch (DescriptorType)
{
case DTYPE_Device:
Address = &DeviceDescriptor;
Size = sizeof(USB_Descriptor_Device_t);
break;
case DTYPE_Configuration:
Address = &ConfigurationDescriptor;
Size = sizeof(USB_Descriptor_Configuration_t);
break;
case DTYPE_String:
switch (DescriptorNumber)
{
case 0x00:
Address = &LanguageString;
Size = pgm_read_byte(&LanguageString.Header.Size);
break;
case 0x01:
Address = &ManufacturerString;
Size = pgm_read_byte(&ManufacturerString.Header.Size);
break;
case 0x02:
Address = &ProductString;
Size = pgm_read_byte(&ProductString.Header.Size);
break;
}
break;
}
*DescriptorAddress = Address;
return Size;
}

92
lufa_serial/Descriptors.h Normal file
View File

@ -0,0 +1,92 @@
/*
* This implementation of a serial.c-like interface for the Teacup firmware
* is based on LUFA/Demos/Device/LowLevel/VirtualSerial.
*
* Modifications by Ben Jackson <ben@ben.com> under GPLv2
*/
/*
LUFA Library
Copyright (C) Dean Camera, 2010.
dean [at] fourwalledcubicle [dot] com
www.lufa-lib.org
*/
/*
Copyright 2010 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby granted
without fee, provided that the above copyright notice appear in
all copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* Header file for Descriptors.c.
*/
#ifndef _DESCRIPTORS_H_
#define _DESCRIPTORS_H_
/* Includes: */
#include <LUFA/Drivers/USB/USB.h>
#include <avr/pgmspace.h>
/* Macros: */
/** Endpoint number of the CDC device-to-host notification IN endpoint. */
#define CDC_NOTIFICATION_EPNUM 2
/** Endpoint number of the CDC device-to-host data IN endpoint. */
#define CDC_TX_EPNUM 3
/** Endpoint number of the CDC host-to-device data OUT endpoint. */
#define CDC_RX_EPNUM 4
/** Size in bytes of the CDC device-to-host notification IN endpoint. */
#define CDC_NOTIFICATION_EPSIZE 8
/** Size in bytes of the CDC data IN and OUT endpoints. */
#define CDC_TXRX_EPSIZE 16
/* Type Defines: */
/** Type define for the device configuration descriptor structure. This must be defined in the
* application code, as the configuration descriptor contains several sub-descriptors which
* vary between devices, and which describe the device's usage to the host.
*/
typedef struct
{
USB_Descriptor_Configuration_Header_t Config;
USB_Descriptor_Interface_t CDC_CCI_Interface;
USB_CDC_Descriptor_FunctionalHeader_t CDC_Functional_Header;
USB_CDC_Descriptor_FunctionalACM_t CDC_Functional_ACM;
USB_CDC_Descriptor_FunctionalUnion_t CDC_Functional_Union;
USB_Descriptor_Endpoint_t CDC_NotificationEndpoint;
USB_Descriptor_Interface_t CDC_DCI_Interface;
USB_Descriptor_Endpoint_t CDC_DataOutEndpoint;
USB_Descriptor_Endpoint_t CDC_DataInEndpoint;
} USB_Descriptor_Configuration_t;
/* Function Prototypes: */
uint16_t CALLBACK_USB_GetDescriptor(const uint16_t wValue,
const uint8_t wIndex,
const void** const DescriptorAddress)
ATTR_WARN_UNUSED_RESULT ATTR_NON_NULL_PTR_ARG(3);
#endif

106
lufa_serial/LUFA Teacup.inf Normal file
View File

@ -0,0 +1,106 @@
;************************************************************
; Windows USB CDC ACM Setup File
; Copyright (c) 2000 Microsoft Corporation
[Version]
Signature="$Windows NT$"
Class=Ports
ClassGuid={4D36E978-E325-11CE-BFC1-08002BE10318}
Provider=%MFGNAME%
LayoutFile=layout.inf
CatalogFile=%MFGFILENAME%.cat
DriverVer=11/15/2007,5.1.2600.0
[Manufacturer]
%MFGNAME%=DeviceList, NTamd64
[DestinationDirs]
DefaultDestDir=12
;------------------------------------------------------------------------------
; Windows 2000/XP/Vista-32bit Sections
;------------------------------------------------------------------------------
[DriverInstall.nt]
include=mdmcpq.inf
CopyFiles=DriverCopyFiles.nt
AddReg=DriverInstall.nt.AddReg
[DriverCopyFiles.nt]
usbser.sys,,,0x20
[DriverInstall.nt.AddReg]
HKR,,DevLoader,,*ntkern
HKR,,NTMPDriver,,%DRIVERFILENAME%.sys
HKR,,EnumPropPages32,,"MsPorts.dll,SerialPortPropPageProvider"
[DriverInstall.nt.Services]
AddService=usbser, 0x00000002, DriverService.nt
[DriverService.nt]
DisplayName=%SERVICE%
ServiceType=1
StartType=3
ErrorControl=1
ServiceBinary=%12%\%DRIVERFILENAME%.sys
;------------------------------------------------------------------------------
; Vista-64bit Sections
;------------------------------------------------------------------------------
[DriverInstall.NTamd64]
include=mdmcpq.inf
CopyFiles=DriverCopyFiles.NTamd64
AddReg=DriverInstall.NTamd64.AddReg
[DriverCopyFiles.NTamd64]
%DRIVERFILENAME%.sys,,,0x20
[DriverInstall.NTamd64.AddReg]
HKR,,DevLoader,,*ntkern
HKR,,NTMPDriver,,%DRIVERFILENAME%.sys
HKR,,EnumPropPages32,,"MsPorts.dll,SerialPortPropPageProvider"
[DriverInstall.NTamd64.Services]
AddService=usbser, 0x00000002, DriverService.NTamd64
[DriverService.NTamd64]
DisplayName=%SERVICE%
ServiceType=1
StartType=3
ErrorControl=1
ServiceBinary=%12%\%DRIVERFILENAME%.sys
;------------------------------------------------------------------------------
; Vendor and Product ID Definitions
;------------------------------------------------------------------------------
; When developing your USB device, the VID and PID used in the PC side
; application program and the firmware on the microcontroller must match.
; Modify the below line to use your VID and PID. Use the format as shown below.
; Note: One INF file can be used for multiple devices with different VID and PIDs.
; For each supported device, append ",USB\VID_xxxx&PID_yyyy" to the end of the line.
;------------------------------------------------------------------------------
[SourceDisksFiles]
[SourceDisksNames]
[DeviceList]
%DESCRIPTION%=DriverInstall, USB\VID_03EB&PID_2044
[DeviceList.NTamd64]
%DESCRIPTION%=DriverInstall, USB\VID_03EB&PID_2044
;------------------------------------------------------------------------------
; String Definitions
;------------------------------------------------------------------------------
;Modify these strings to customize your device
;------------------------------------------------------------------------------
[Strings]
MFGFILENAME="CDC_vista"
DRIVERFILENAME ="usbser"
MFGNAME="http://www.lufa-lib.org"
INSTDISK="LUFA CDC Driver Installer"
DESCRIPTION="Communications Port"
SERVICE="USB RS-232 Emulation Driver"

237
lufa_serial/lufa_serial.c Normal file
View File

@ -0,0 +1,237 @@
/*
* This implementation of a serial.c-like interface for the Teacup firmware
* is based on LUFA/Demos/Device/LowLevel/VirtualSerial.
*
* Modifications by Ben Jackson <ben@ben.com> under GPLv2
*/
/*
LUFA Library
Copyright (C) Dean Camera, 2010.
dean [at] fourwalledcubicle [dot] com
www.lufa-lib.org
*/
/*
Copyright 2010 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby granted
without fee, provided that the above copyright notice appear in
all copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* Main source file for the VirtualSerial demo. This file contains the main tasks of the demo and
* is responsible for the initial application hardware configuration.
*/
#include "lufa_serial.h"
#include <avr/pgmspace.h>
/** Contains the current baud rate and other settings of the virtual serial port. While this demo does not use
* the physical USART and thus does not use these settings, they must still be retained and returned to the host
* upon request or the host will assume the device is non-functional.
*
* These values are set by the host via a class-specific request, however they are not required to be used accurately.
* It is possible to completely ignore these value or use other settings as the host is completely unaware of the physical
* serial link characteristics and instead sends and receives data in endpoint streams.
*/
CDC_LineEncoding_t LineEncoding = { .BaudRateBPS = 0,
.CharFormat = CDC_LINEENCODING_OneStopBit,
.ParityType = CDC_PARITY_None,
.DataBits = 8 };
void serial_init(void)
{
/* Disable clock division */
clock_prescale_set(clock_div_1);
LEDs_Init();
USB_Init();
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
}
/** Event handler for the USB_Connect event. This indicates that the device is enumerating via the status LEDs and
* starts the library USB task to begin the enumeration and USB management process.
*/
void EVENT_USB_Device_Connect(void)
{
/* Indicate USB enumerating */
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
}
/** Event handler for the USB_Disconnect event. This indicates that the device is no longer connected to a host via
// * the status LEDs and stops the USB management and CDC management tasks.
*/
void EVENT_USB_Device_Disconnect(void)
{
/* Indicate USB not ready */
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
}
/** Event handler for the USB_ConfigurationChanged event. This is fired when the host set the current configuration
* of the USB device after enumeration - the device endpoints are configured and the CDC management task started.
*/
void EVENT_USB_Device_ConfigurationChanged(void)
{
bool ConfigSuccess = true;
/* Setup CDC Data Endpoints */
ConfigSuccess &= Endpoint_ConfigureEndpoint(CDC_NOTIFICATION_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_IN,
CDC_NOTIFICATION_EPSIZE, ENDPOINT_BANK_SINGLE);
ConfigSuccess &= Endpoint_ConfigureEndpoint(CDC_TX_EPNUM, EP_TYPE_BULK, ENDPOINT_DIR_IN,
CDC_TXRX_EPSIZE, ENDPOINT_BANK_SINGLE);
ConfigSuccess &= Endpoint_ConfigureEndpoint(CDC_RX_EPNUM, EP_TYPE_BULK, ENDPOINT_DIR_OUT,
CDC_TXRX_EPSIZE, ENDPOINT_BANK_SINGLE);
/* Reset line encoding baud rate so that the host knows to send new values */
LineEncoding.BaudRateBPS = 0;
/* Indicate endpoint configuration success or failure */
LEDs_SetAllLEDs(ConfigSuccess ? LEDMASK_USB_READY : LEDMASK_USB_ERROR);
}
/** Event handler for the USB_ControlRequest event. This is used to catch and process control requests sent to
* the device from the USB host before passing along unhandled control requests to the library for processing
* internally.
*/
void EVENT_USB_Device_ControlRequest(void)
{
/* Process CDC specific control requests */
switch (USB_ControlRequest.bRequest)
{
case CDC_REQ_GetLineEncoding:
if (USB_ControlRequest.bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))
{
Endpoint_ClearSETUP();
/* Write the line coding data to the control endpoint */
Endpoint_Write_Control_Stream_LE(&LineEncoding, sizeof(CDC_LineEncoding_t));
Endpoint_ClearOUT();
}
break;
case CDC_REQ_SetLineEncoding:
if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
{
Endpoint_ClearSETUP();
/* Read the line coding data in from the host into the global struct */
Endpoint_Read_Control_Stream_LE(&LineEncoding, sizeof(CDC_LineEncoding_t));
Endpoint_ClearIN();
}
break;
case CDC_REQ_SetControlLineState:
if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
{
Endpoint_ClearSETUP();
Endpoint_ClearStatusStage();
/* NOTE: Here you can read in the line state mask from the host, to get the current state of the output handshake
lines. The mask is read in from the wValue parameter in USB_ControlRequest, and can be masked against the
CONTROL_LINE_OUT_* masks to determine the RTS and DTR line states using the following code:
*/
}
break;
}
}
static void serial_flush(void)
{
/* Remember if the packet to send completely fills the endpoint */
bool IsFull = (Endpoint_BytesInEndpoint() == CDC_TXRX_EPSIZE);
/* Finalize the stream transfer to send the last packet */
Endpoint_ClearIN();
/* If the last packet filled the endpoint, send an empty packet to release the buffer on
* the receiver (otherwise all data will be cached until a non-full packet is received) */
if (IsFull)
{
/* Wait until the endpoint is ready for another packet */
Endpoint_WaitUntilReady();
/* Send an empty packet to ensure that the host does not buffer data sent to it */
Endpoint_ClearIN();
}
}
uint8_t serial_rxchars(void)
{
/* Rely on polling of this from mendel.c to run USBTask */
USB_USBTask();
if (USB_DeviceState != DEVICE_STATE_Configured)
return 0;
/* Select the Serial Rx Endpoint */
Endpoint_SelectEndpoint(CDC_RX_EPNUM);
return Endpoint_IsOUTReceived();
}
uint8_t serial_popchar(void)
{
if (USB_DeviceState != DEVICE_STATE_Configured)
return 0;
uint8_t c = 0;
/* Select the Serial Rx Endpoint */
Endpoint_SelectEndpoint(CDC_RX_EPNUM);
Endpoint_Read_Stream_LE(&c, 1);
return c;
}
void serial_writestr_P(PGM_P data)
{
if (USB_DeviceState != DEVICE_STATE_Configured)
return;
/* Select the Serial Tx Endpoint */
Endpoint_SelectEndpoint(CDC_TX_EPNUM);
size_t len = strlen_P(data);
/*
if (pgm_read_byte(&data[len-1]) == '\n') {
Endpoint_Write_PStream_LE(data, len-1);
Endpoint_Write_PStream_LE(PSTR("\r\n"), 2);
} else */ {
Endpoint_Write_PStream_LE(data, len);
}
serial_flush();
}
void serial_writechar(uint8_t data)
{
if (USB_DeviceState != DEVICE_STATE_Configured)
return;
/*
if (data == '\n') {
serial_writestr_P(PSTR("\r\n"));
return;
}
*/
/* Select the Serial Tx Endpoint */
Endpoint_SelectEndpoint(CDC_TX_EPNUM);
Endpoint_Write_Stream_LE(&data, 1);
serial_flush();
}

83
lufa_serial/lufa_serial.h Normal file
View File

@ -0,0 +1,83 @@
/*
* This implementation of a serial.c-like interface for the Teacup firmware
* is based on LUFA/Demos/Device/LowLevel/VirtualSerial.
*
* Modifications by Ben Jackson <ben@ben.com> under GPLv2
*/
/*
LUFA Library
Copyright (C) Dean Camera, 2010.
dean [at] fourwalledcubicle [dot] com
www.lufa-lib.org
*/
/*
Copyright 2010 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby granted
without fee, provided that the above copyright notice appear in
all copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* Header file for VirtualSerial.c.
*/
#ifndef _VIRTUALSERIAL_H_
#define _VIRTUALSERIAL_H_
/* Includes: */
#include <avr/io.h>
#include <avr/wdt.h>
#include <avr/power.h>
#include <avr/interrupt.h>
#include <string.h>
#include "Descriptors.h"
#include <LUFA/Version.h>
#include <LUFA/Drivers/USB/USB.h>
#include <LUFA/Drivers/Board/Joystick.h>
#include <LUFA/Drivers/Board/LEDs.h>
/* Macros: */
/** LED mask for the library LED driver, to indicate that the USB interface is not ready. */
#define LEDMASK_USB_NOTREADY LEDS_LED1
/** LED mask for the library LED driver, to indicate that the USB interface is enumerating. */
#define LEDMASK_USB_ENUMERATING (LEDS_LED2 | LEDS_LED3)
/** LED mask for the library LED driver, to indicate that the USB interface is ready. */
#define LEDMASK_USB_READY (LEDS_LED2 | LEDS_LED4)
/** LED mask for the library LED driver, to indicate that an error has occurred in the USB interface. */
#define LEDMASK_USB_ERROR (LEDS_LED1 | LEDS_LED3)
/* Function Prototypes: */
void SetupHardware(void);
void CDC_Task(void);
void EVENT_USB_Device_Connect(void);
void EVENT_USB_Device_Disconnect(void);
void EVENT_USB_Device_ConfigurationChanged(void);
void EVENT_USB_Device_ControlRequest(void);
#endif

698
lufa_serial/makefile Normal file
View File

@ -0,0 +1,698 @@
# Hey Emacs, this is a -*- makefile -*-
#----------------------------------------------------------------------------
# WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
# >> Modified for use with the LUFA project. <<
#
# Released to the Public Domain
#
# Additional material for this makefile was written by:
# Peter Fleury
# Tim Henigan
# Colin O'Flynn
# Reiner Patommel
# Markus Pfaff
# Sander Pool
# Frederik Rouleau
# Carlos Lamas
# Dean Camera
# Opendous Inc.
# Denver Gingerich
#
#----------------------------------------------------------------------------
# On command line:
#
# make all = Make software.
#
# make clean = Clean out built project files.
#
# make coff = Convert ELF to AVR COFF.
#
# make extcoff = Convert ELF to AVR Extended COFF.
#
# make program = Download the hex file to the device, using avrdude.
# Please customize the avrdude settings below first!
#
# make dfu = Download the hex file to the device, using dfu-programmer (must
# have dfu-programmer installed).
#
# make flip = Download the hex file to the device, using Atmel FLIP (must
# have Atmel FLIP installed).
#
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
# (must have dfu-programmer installed).
#
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
# (must have Atmel FLIP installed).
#
# make doxygen = Generate DoxyGen documentation for the project (must have
# DoxyGen installed)
#
# make debug = Start either simulavr or avarice as specified for debugging,
# with avr-gdb or avr-insight as the front end for debugging.
#
# make filename.s = Just compile filename.c into the assembler code only.
#
# make filename.i = Create a preprocessed source file for use in submitting
# bug reports to the GCC project.
#
# To rebuild project do "make clean" then "make all".
#----------------------------------------------------------------------------
# MCU name
MCU = at90usb1287
# Target board (see library "Board Types" documentation, NONE for projects not requiring
# LUFA board drivers). If USER is selected, put custom board drivers in a directory called
# "Board" inside the application directory.
BOARD = USBKEY
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_CLOCK below, as it is sourced by
# F_CLOCK after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 8000000
# Input clock frequency.
# This will define a symbol, F_CLOCK, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_CLOCK = $(F_CPU)
# Output format. (can be srec, ihex, binary)
FORMAT = ihex
# Target file name (without extension).
TARGET = lufa_serial
# Object files directory
# To put object files in current directory, use a dot (.), do NOT make
# this an empty or blank macro!
OBJDIR = .
# Path to the LUFA library
LUFA_PATH = ../LUFA/trunk
# LUFA library compile-time options and predefined tokens
LUFA_OPTS = -D USB_DEVICE_ONLY
LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8
LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1
LUFA_OPTS += -D USE_FLASH_DESCRIPTORS
LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
LUFA_OPTS += -D NO_STREAM_CALLBACKS
# Create the LUFA source path variables by including the LUFA root makefile
include $(LUFA_PATH)/LUFA/makefile
# List C source files here. (C dependencies are automatically generated.)
SRC = $(TARGET).c \
Descriptors.c \
$(LUFA_SRC_USB)
# List C++ source files here. (C dependencies are automatically generated.)
CPPSRC =
# List Assembler source files here.
# Make them always end in a capital .S. Files ending in a lowercase .s
# will not be considered source files but generated files (assembler
# output from the compiler), and will be deleted upon "make clean"!
# Even though the DOS/Win* filesystem matches both .s and .S the same,
# it will preserve the spelling of the filenames, and gcc itself does
# care about how the name is spelled on its command-line.
ASRC =
# Optimization level, can be [0, 1, 2, 3, s].
# 0 = turn off optimization. s = optimize for size.
# (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
OPT = s
# Debugging format.
# Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.
# AVR Studio 4.10 requires dwarf-2.
# AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.
DEBUG = dwarf-2
# List any extra directories to look for include files here.
# Each directory must be seperated by a space.
# Use forward slashes for directory separators.
# For a directory that has spaces, enclose it in quotes.
EXTRAINCDIRS = $(LUFA_PATH)/
# Compiler flag to set the C Standard level.
# c89 = "ANSI" C
# gnu89 = c89 plus GCC extensions
# c99 = ISO C99 standard (not yet fully implemented)
# gnu99 = c99 plus GCC extensions
CSTANDARD = -std=c99
# Place -D or -U options here for C sources
CDEFS = -DF_CPU=$(F_CPU)UL
CDEFS += -DF_CLOCK=$(F_CLOCK)UL
CDEFS += -DBOARD=BOARD_$(BOARD)
CDEFS += $(LUFA_OPTS)
# Place -D or -U options here for ASM sources
ADEFS = -DF_CPU=$(F_CPU)
ADEFS += -DF_CLOCK=$(F_CLOCK)UL
ADEFS += -DBOARD=BOARD_$(BOARD)
ADEFS += $(LUFA_OPTS)
# Place -D or -U options here for C++ sources
CPPDEFS = -DF_CPU=$(F_CPU)UL
CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL
CPPDEFS += -DBOARD=BOARD_$(BOARD)
CPPDEFS += $(LUFA_OPTS)
#CPPDEFS += -D__STDC_LIMIT_MACROS
#CPPDEFS += -D__STDC_CONSTANT_MACROS
#---------------- Compiler Options C ----------------
# -g*: generate debugging information
# -O*: optimization level
# -f...: tuning, see GCC manual and avr-libc documentation
# -Wall...: warning level
# -Wa,...: tell GCC to pass this to the assembler.
# -adhlns...: create assembler listing
CFLAGS = -g$(DEBUG)
CFLAGS += $(CDEFS)
CFLAGS += -O$(OPT)
CFLAGS += -funsigned-char
CFLAGS += -funsigned-bitfields
CFLAGS += -ffunction-sections
CFLAGS += -fno-inline-small-functions
CFLAGS += -fpack-struct
CFLAGS += -fshort-enums
CFLAGS += -fno-strict-aliasing
CFLAGS += -Wall
CFLAGS += -Wstrict-prototypes
#CFLAGS += -mshort-calls
#CFLAGS += -fno-unit-at-a-time
#CFLAGS += -Wundef
#CFLAGS += -Wunreachable-code
#CFLAGS += -Wsign-compare
CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
CFLAGS += $(CSTANDARD)
#---------------- Compiler Options C++ ----------------
# -g*: generate debugging information
# -O*: optimization level
# -f...: tuning, see GCC manual and avr-libc documentation
# -Wall...: warning level
# -Wa,...: tell GCC to pass this to the assembler.
# -adhlns...: create assembler listing
CPPFLAGS = -g$(DEBUG)
CPPFLAGS += $(CPPDEFS)
CPPFLAGS += -O$(OPT)
CPPFLAGS += -funsigned-char
CPPFLAGS += -funsigned-bitfields
CPPFLAGS += -fpack-struct
CPPFLAGS += -fshort-enums
CPPFLAGS += -fno-exceptions
CPPFLAGS += -Wall
CPPFLAGS += -Wundef
#CPPFLAGS += -mshort-calls
#CPPFLAGS += -fno-unit-at-a-time
#CPPFLAGS += -Wstrict-prototypes
#CPPFLAGS += -Wunreachable-code
#CPPFLAGS += -Wsign-compare
CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
#CPPFLAGS += $(CSTANDARD)
#---------------- Assembler Options ----------------
# -Wa,...: tell GCC to pass this to the assembler.
# -adhlns: create listing
# -gstabs: have the assembler create line number information; note that
# for use in COFF files, additional information about filenames
# and function names needs to be present in the assembler source
# files -- see avr-libc docs [FIXME: not yet described there]
# -listing-cont-lines: Sets the maximum number of continuation lines of hex
# dump that will be displayed for a given single line of source input.
ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
#---------------- Library Options ----------------
# Minimalistic printf version
PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min
# Floating point printf version (requires MATH_LIB = -lm below)
PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
# If this is left blank, then it will use the Standard printf version.
PRINTF_LIB =
#PRINTF_LIB = $(PRINTF_LIB_MIN)
#PRINTF_LIB = $(PRINTF_LIB_FLOAT)
# Minimalistic scanf version
SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min
# Floating point + %[ scanf version (requires MATH_LIB = -lm below)
SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
# If this is left blank, then it will use the Standard scanf version.
SCANF_LIB =
#SCANF_LIB = $(SCANF_LIB_MIN)
#SCANF_LIB = $(SCANF_LIB_FLOAT)
MATH_LIB = -lm
# List any extra directories to look for libraries here.
# Each directory must be seperated by a space.
# Use forward slashes for directory separators.
# For a directory that has spaces, enclose it in quotes.
EXTRALIBDIRS =
#---------------- External Memory Options ----------------
# 64 KB of external RAM, starting after internal RAM (ATmega128!),
# used for variables (.data/.bss) and heap (malloc()).
#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff
# 64 KB of external RAM, starting after internal RAM (ATmega128!),
# only used for heap (malloc()).
#EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff
EXTMEMOPTS =
#---------------- Linker Options ----------------
# -Wl,...: tell GCC to pass this to linker.
# -Map: create map file
# --cref: add cross reference to map file
LDFLAGS = -Wl,-Map=$(TARGET).map,--cref
LDFLAGS += -Wl,--relax
LDFLAGS += -Wl,--gc-sections
LDFLAGS += $(EXTMEMOPTS)
LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)
#LDFLAGS += -T linker_script.x
#---------------- Programming Options (avrdude) ----------------
# Programming hardware
# Type: avrdude -c ?
# to get a full listing.
#
AVRDUDE_PROGRAMMER = jtagmkII
# com1 = serial port. Use lpt1 to connect to parallel port.
AVRDUDE_PORT = usb
AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
# Uncomment the following if you want avrdude's erase cycle counter.
# Note that this counter needs to be initialized first using -Yn,
# see avrdude manual.
#AVRDUDE_ERASE_COUNTER = -y
# Uncomment the following if you do /not/ wish a verification to be
# performed after programming the device.
#AVRDUDE_NO_VERIFY = -V
# Increase verbosity level. Please use this when submitting bug
# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
# to submit bug reports.
#AVRDUDE_VERBOSE = -v -v
AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
#---------------- Debugging Options ----------------
# For simulavr only - target MCU frequency.
DEBUG_MFREQ = $(F_CPU)
# Set the DEBUG_UI to either gdb or insight.
# DEBUG_UI = gdb
DEBUG_UI = insight
# Set the debugging back-end to either avarice, simulavr.
DEBUG_BACKEND = avarice
#DEBUG_BACKEND = simulavr
# GDB Init Filename.
GDBINIT_FILE = __avr_gdbinit
# When using avarice settings for the JTAG
JTAG_DEV = /dev/com1
# Debugging port used to communicate between GDB / avarice / simulavr.
DEBUG_PORT = 4242
# Debugging host used to communicate between GDB / avarice / simulavr, normally
# just set to localhost unless doing some sort of crazy debugging when
# avarice is running on a different computer.
DEBUG_HOST = localhost
#============================================================================
# Define programs and commands.
SHELL = sh
CC = avr-gcc
OBJCOPY = avr-objcopy
OBJDUMP = avr-objdump
SIZE = avr-size
AR = avr-ar rcs
NM = avr-nm
AVRDUDE = avrdude
REMOVE = rm -f
REMOVEDIR = rm -rf
COPY = cp
WINSHELL = cmd
# Define Messages
# English
MSG_ERRORS_NONE = Errors: none
MSG_BEGIN = -------- begin --------
MSG_END = -------- end --------
MSG_SIZE_BEFORE = Size before:
MSG_SIZE_AFTER = Size after:
MSG_COFF = Converting to AVR COFF:
MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
MSG_FLASH = Creating load file for Flash:
MSG_EEPROM = Creating load file for EEPROM:
MSG_EXTENDED_LISTING = Creating Extended Listing:
MSG_SYMBOL_TABLE = Creating Symbol Table:
MSG_LINKING = Linking:
MSG_COMPILING = Compiling C:
MSG_COMPILING_CPP = Compiling C++:
MSG_ASSEMBLING = Assembling:
MSG_CLEANING = Cleaning project:
MSG_CREATING_LIBRARY = Creating library:
# Define all object files.
OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
# Define all listing files.
LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
# Compiler flags to generate dependency files.
GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d
# Combine all necessary flags and optional flags.
# Add target processor to flags.
ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)
ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)
ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
# Default target.
all: build
# Change the build target to build a HEX file or a library.
#build: elf hex eep lss sym
build: lib
elf: $(TARGET).elf
hex: $(TARGET).hex
eep: $(TARGET).eep
lss: $(TARGET).lss
sym: $(TARGET).sym
LIBNAME=lib$(TARGET).a
lib: $(LIBNAME)
# Display size of file.
HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
ELFSIZE = $(SIZE) $(MCU_FLAG) $(FORMAT_FLAG) $(TARGET).elf
MCU_FLAG = $(shell $(SIZE) --help | grep -- --mcu > /dev/null && echo --mcu=$(MCU) )
FORMAT_FLAG = $(shell $(SIZE) --help | grep -- --format=.*avr > /dev/null && echo --format=avr )
sizebefore:
@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \
2>/dev/null; echo; fi
sizeafter:
@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
2>/dev/null; echo; fi
# Program the device.
program: $(TARGET).hex $(TARGET).eep
$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
flip: $(TARGET).hex
batchisp -hardware usb -device $(MCU) -operation erase f
batchisp -hardware usb -device $(MCU) -operation loadbuffer $(TARGET).hex program
batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu: $(TARGET).hex
dfu-programmer $(MCU) erase
dfu-programmer $(MCU) flash $(TARGET).hex
dfu-programmer $(MCU) reset
flip-ee: $(TARGET).hex $(TARGET).eep
$(COPY) $(TARGET).eep $(TARGET)eep.hex
batchisp -hardware usb -device $(MCU) -operation memory EEPROM erase
batchisp -hardware usb -device $(MCU) -operation memory EEPROM loadbuffer $(TARGET)eep.hex program
batchisp -hardware usb -device $(MCU) -operation start reset 0
$(REMOVE) $(TARGET)eep.hex
dfu-ee: $(TARGET).hex $(TARGET).eep
dfu-programmer $(MCU) eeprom-flash $(TARGET).eep
dfu-programmer $(MCU) reset
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
gdb-config:
@$(REMOVE) $(GDBINIT_FILE)
@echo define reset >> $(GDBINIT_FILE)
@echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
@echo end >> $(GDBINIT_FILE)
@echo file $(TARGET).elf >> $(GDBINIT_FILE)
@echo target remote $(DEBUG_HOST):$(DEBUG_PORT) >> $(GDBINIT_FILE)
ifeq ($(DEBUG_BACKEND),simulavr)
@echo load >> $(GDBINIT_FILE)
endif
@echo break main >> $(GDBINIT_FILE)
debug: gdb-config $(TARGET).elf
ifeq ($(DEBUG_BACKEND), avarice)
@echo Starting AVaRICE - Press enter when "waiting to connect" message displays.
@$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \
$(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)
@$(WINSHELL) /c pause
else
@$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \
$(DEBUG_MFREQ) --port $(DEBUG_PORT)
endif
@$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)
# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
COFFCONVERT = $(OBJCOPY) --debugging
COFFCONVERT += --change-section-address .data-0x800000
COFFCONVERT += --change-section-address .bss-0x800000
COFFCONVERT += --change-section-address .noinit-0x800000
COFFCONVERT += --change-section-address .eeprom-0x810000
coff: $(TARGET).elf
@echo
@echo $(MSG_COFF) $(TARGET).cof
$(COFFCONVERT) -O coff-avr $< $(TARGET).cof
extcoff: $(TARGET).elf
@echo
@echo $(MSG_EXTENDED_COFF) $(TARGET).cof
$(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof
# Create final output files (.hex, .eep) from ELF output file.
%.hex: %.elf
@echo
@echo $(MSG_FLASH) $@
$(OBJCOPY) -O $(FORMAT) -R .eeprom -R .fuse -R .lock $< $@
%.eep: %.elf
@echo
@echo $(MSG_EEPROM) $@
-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
--change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0
# Create extended listing file from ELF output file.
%.lss: %.elf
@echo
@echo $(MSG_EXTENDED_LISTING) $@
$(OBJDUMP) -h -S -z $< > $@
# Create a symbol table from ELF output file.
%.sym: %.elf
@echo
@echo $(MSG_SYMBOL_TABLE) $@
$(NM) -n $< > $@
# Create library from object files.
.SECONDARY : $(TARGET).a
.PRECIOUS : $(OBJ)
%.a: $(OBJ)
@echo
@echo $(MSG_CREATING_LIBRARY) $@
$(AR) $@ $(OBJ)
# Link: create ELF output file from object files.
.SECONDARY : $(TARGET).elf
.PRECIOUS : $(OBJ)
%.elf: $(OBJ)
@echo
@echo $(MSG_LINKING) $@
$(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)
# Compile: create object files from C source files.
$(OBJDIR)/%.o : %.c
@echo
@echo $(MSG_COMPILING) $<
$(CC) -c $(ALL_CFLAGS) $< -o $@
# Compile: create object files from C++ source files.
$(OBJDIR)/%.o : %.cpp
@echo
@echo $(MSG_COMPILING_CPP) $<
$(CC) -c $(ALL_CPPFLAGS) $< -o $@
# Compile: create assembler files from C source files.
%.s : %.c
$(CC) -S $(ALL_CFLAGS) $< -o $@
# Compile: create assembler files from C++ source files.
%.s : %.cpp
$(CC) -S $(ALL_CPPFLAGS) $< -o $@
# Assemble: create object files from assembler source files.
$(OBJDIR)/%.o : %.S
@echo
@echo $(MSG_ASSEMBLING) $<
$(CC) -c $(ALL_ASFLAGS) $< -o $@
# Create preprocessed source for use in sending a bug report.
%.i : %.c
$(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
# Target: clean project.
clean: begin clean_list end
clean_list :
@echo
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).hex
$(REMOVE) $(TARGET).eep
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
$(REMOVE) $(TARGET).sym
$(REMOVE) $(TARGET).lss
$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
$(REMOVE) $(SRC:.c=.s)
$(REMOVE) $(SRC:.c=.d)
$(REMOVE) $(SRC:.c=.i)
$(REMOVE) $(LIBNAME)
$(REMOVEDIR) .dep
doxygen:
@echo Generating Project Documentation...
@doxygen Doxygen.conf
@echo Documentation Generation Complete.
clean_doxygen:
rm -rf Documentation
# Create object files directory
$(shell mkdir $(OBJDIR) 2>/dev/null)
# Include the dependency files.
-include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)
# Listing of phony targets.
.PHONY : all begin finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff doxygen clean \
clean_list clean_doxygen program dfu flip flip-ee dfu-ee \
debug gdb-config