josh
/
Teacup_Firmware
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

board.gen7-arm.h: adjust for the released Gen7-ARM. 

Just a few pin changes and similar stuff, no code change.
This commit is contained in:
Markus Hitter 2015-11-27 16:54:41 +01:00
parent 82374b8e24
commit 7faab99671
2 changed files with 12 additions and 18 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

12
Makefile-ARM
View File

@ -41,13 +41,6 @@
##############################################################################
MCU ?= lpc1114
# MCU ?= atmega328p
# MCU ?= atmega644
# MCU ?= atmega1284p
# MCU ?= atmega1280
# MCU ?= atmega2560
# MCU ?= at90usb1286
# MCU ?= atmega32u4
# CPU clock rate not defined here, but in the CMSIS headers.
@ -74,11 +67,12 @@ TOOLCHAIN = arm-none-eabi-
# in the rules for the 'program' target.
# Frequency of the on-chip R/C oscillator or the on-board quartz crystal.
# Not to confuse with the CPU's clock frequency, which is usually much higher.
F_CRYSTAL ?= 12000000
# Serial port the electronics is connected to.
UPLOADER_PORT ?= /dev/ttyUSB0
#UPLOADER_PORT ?= /dev/ttyACM0
#UPLOADER_PORT ?= /dev/ttyUSB0
UPLOADER_PORT ?= /dev/ttyACM0
#UPLOADER_PORT ?= com1
##############################################################################

18
config/board.gen7-arm.h
View File

@ -75,15 +75,15 @@
//#define Z_INVERT_MAX
//#define Z_INVERT_ENABLE
#define E_STEP_PIN PIO0_4
#define E_STEP_PIN PIO0_3
#define E_DIR_PIN PIO0_7
//#define E_ENABLE_PIN xxxx
//#define E_INVERT_DIR
//#define E_INVERT_ENABLE
#define PS_ON_PIN PIO0_3
#define PS_ON_PIN PIO0_4
//#define PS_MOSFET_PIN xxxx
#define STEPPER_ENABLE_PIN PIO0_3
#define STEPPER_ENABLE_PIN PIO0_4
#define STEPPER_INVERT_ENABLE
/** \def DEBUG_LED_PIN
@ -96,7 +96,7 @@
a LED in hardware), see
http://reprap.org/wiki/Teacup_Firmware#Doing_precision_profiling
*/
#define DEBUG_LED_PIN PIO1_9
//#define DEBUG_LED_PIN PIO1_9
/** \def SD_CARD_SELECT_PIN
@ -163,12 +163,12 @@
*/
//DEFINE_TEMP_SENSORS_START
// name type pin additional
DEFINE_TEMP_SENSOR(extruder, TT_THERMISTOR, PIO1_0,THERMISTOR_EXTRUDER)
DEFINE_TEMP_SENSOR(bed, TT_THERMISTOR, PIO1_1,THERMISTOR_BED)
DEFINE_TEMP_SENSOR(extruder, TT_THERMISTOR, PIO1_1,THERMISTOR_EXTRUDER)
DEFINE_TEMP_SENSOR(bed, TT_THERMISTOR, PIO1_0,THERMISTOR_BED)
// Beta algorithm r0 beta r2 vadc
// Steinhart-Hart rp t0 r0 t1 r1 t2 r2
//TEMP_TABLE EXTRUDER (100000, 4092, 4700, 5.0)
//TEMP_TABLE EXTRUDER (100000, 4092, 1000, 5.0)
//TEMP_TABLE BED (100000, 4092, 4700, 5.0)
//DEFINE_TEMP_SENSORS_END
@ -188,7 +188,7 @@ DEFINE_TEMP_SENSOR(bed, TT_THERMISTOR, PIO1_1,THERMISTOR_BED)
commented out.
*/
//#define HEATER_PIN PIO0_10
//#define HEATER_PIN PIO0_11
//#define HEATER_PIN PIO1_9
/** \def DEFINE_HEATER
Define your heaters and devices here.
@ -233,7 +233,7 @@ DEFINE_TEMP_SENSOR(bed, TT_THERMISTOR, PIO1_1,THERMISTOR_BED)
//DEFINE_HEATERS_START
// name pin invert pwm
DEFINE_HEATER(extruder, PIO0_10, 0, 20000)
DEFINE_HEATER(bed, PIO0_11, 1, 10)
DEFINE_HEATER(bed, PIO1_9, 1, 10)
#define HEATER_EXTRUDER HEATER_extruder
#define HEATER_BED HEATER_bed