Configtool: convert template for Sanguinololu v1.1.
This commit is contained in:
jbernardis
Markus Hitter
parent
7ebdb81ce7
commit
821e0c1295
|
|
@ -11,6 +11,7 @@
|
|||
#include "config/board.gen7-v1.4.h"
|
||||
//#include "config/board.ramps-v1.2.h"
|
||||
//#include "config/board.ramps-v1.3.h"
|
||||
//#include "config/board.sanguinololu-v1.1.h"
|
||||
|
||||
// Uncomment your printer type, comment out all others.
|
||||
#include "config/printer.mendel.h"
|
||||
|
|
|
|||
|
|
@ -0,0 +1,234 @@
|
|||
|
||||
/***************************************************************************\
|
||||
* *
|
||||
* 1. CPU *
|
||||
* *
|
||||
\***************************************************************************/
|
||||
|
||||
/** \def CPU_TYPE
|
||||
CPU types a user should be able to choose from in configtool. All
|
||||
commented out.
|
||||
*/
|
||||
//#define CPU_TYPE atmega644
|
||||
//#define CPU_TYPE atmega644p
|
||||
//#define CPU_TYPE atmega1284
|
||||
//#define CPU_TYPE atmega1284p
|
||||
|
||||
/** \def CPU
|
||||
CPU actually present on the board.
|
||||
*/
|
||||
#define CPU atmega644p
|
||||
|
||||
/** \def F_CPU_OPT
|
||||
CPU clock frequencies a user should be able to choose from in configtool.
|
||||
All commented out.
|
||||
*/
|
||||
//#define F_CPU_OPT 16000000UL
|
||||
|
||||
/** \def F_CPU
|
||||
Actual CPU clock rate. #ifndef required for Arduino compatibility.
|
||||
*/
|
||||
#ifndef F_CPU
|
||||
#define F_CPU 16000000UL
|
||||
#endif
|
||||
|
||||
/** \def MOTHERBOARD
|
||||
This is the motherboard, as opposed to the extruder. See extruder/ directory
|
||||
for GEN3 extruder firmware.
|
||||
*/
|
||||
#define MOTHERBOARD
|
||||
|
||||
|
||||
/***************************************************************************\
|
||||
* *
|
||||
* 2. PINOUTS *
|
||||
* *
|
||||
\***************************************************************************/
|
||||
|
||||
#include "../arduino.h"
|
||||
|
||||
#define X_STEP_PIN DIO15
|
||||
#define X_DIR_PIN DIO21
|
||||
#define X_MIN_PIN DIO18
|
||||
//#define X_MAX_PIN xxxx
|
||||
//#define X_ENABLE_PIN xxxx
|
||||
//#define X_INVERT_DIR
|
||||
//#define X_INVERT_MIN
|
||||
//#define X_INVERT_MAX
|
||||
//#define X_INVERT_ENABLE
|
||||
|
||||
#define Y_STEP_PIN DIO22
|
||||
#define Y_DIR_PIN DIO23
|
||||
#define Y_MIN_PIN DIO19
|
||||
//#define Y_MAX_PIN xxxx
|
||||
//#define Y_ENABLE_PIN xxxx
|
||||
//#define Y_INVERT_DIR
|
||||
//#define Y_INVERT_MIN
|
||||
//#define Y_INVERT_MAX
|
||||
//#define Y_INVERT_ENABLE
|
||||
|
||||
#define Z_STEP_PIN DIO3
|
||||
#define Z_DIR_PIN DIO2
|
||||
#define Z_MIN_PIN DIO20
|
||||
//#define Z_MAX_PIN xxxx
|
||||
//#define Z_ENABLE_PIN xxxx
|
||||
//#define Z_INVERT_DIR
|
||||
//#define Z_INVERT_MIN
|
||||
//#define Z_INVERT_MAX
|
||||
//#define Z_INVERT_ENABLE
|
||||
|
||||
#define E_STEP_PIN DIO1
|
||||
#define E_DIR_PIN DIO0
|
||||
//#define E_ENABLE_PIN xxxx
|
||||
//#define E_INVERT_DIR
|
||||
//#define E_INVERT_ENABLE
|
||||
|
||||
#define PS_ON_PIN DIO9
|
||||
//#define PS_MOSFET_PIN xxxx
|
||||
#define STEPPER_ENABLE_PIN DIO4
|
||||
//#define STEPPER_INVERT_ENABLE
|
||||
|
||||
/** \def DEBUG_LED_PIN
|
||||
|
||||
Enable flashing of a LED during motor stepping.
|
||||
|
||||
Disabled by default. Uncommenting this makes the binary a few bytes larger
|
||||
and adds a few cycles to the step timing interrrupt in timer.c. Also used
|
||||
for precision profiling (profiling works even without actually having such
|
||||
a LED in hardware), see
|
||||
http://reprap.org/wiki/Teacup_Firmware#Doing_precision_profiling
|
||||
*/
|
||||
//#define DEBUG_LED_PIN DIO13
|
||||
|
||||
|
||||
/***************************************************************************\
|
||||
* *
|
||||
* 3. TEMPERATURE SENSORS *
|
||||
* *
|
||||
\***************************************************************************/
|
||||
|
||||
#ifndef DEFINE_TEMP_SENSOR
|
||||
#define DEFINE_TEMP_SENSOR(...)
|
||||
#endif
|
||||
|
||||
/** \def TEMP_MAX6675 TEMP_THERMISTOR TEMP_AD595 TEMP_PT100 TEMP_INTERCOM
|
||||
Which temperature sensor types are you using? Leave all used ones
|
||||
uncommented, comment out all others to save binary size and enhance
|
||||
performance.
|
||||
*/
|
||||
//#define TEMP_MAX6675
|
||||
#define TEMP_THERMISTOR
|
||||
//#define TEMP_AD595
|
||||
//#define TEMP_PT100
|
||||
//#define TEMP_INTERCOM
|
||||
|
||||
/** \def TEMP_SENSOR_PIN
|
||||
Temperature sensor pins a user should be able to choose from in configtool.
|
||||
All commented out.
|
||||
*/
|
||||
//#define TEMP_SENSOR_PIN AIO6
|
||||
//#define TEMP_SENSOR_PIN AIO7
|
||||
|
||||
/** \def DEFINE_TEMP_SENSOR
|
||||
Define your temperature sensors here. One line for each sensor, only
|
||||
limited by the number of available ATmega pins.
|
||||
|
||||
Types are same as TEMP_ list above - TT_MAX6675, TT_THERMISTOR, TT_AD595,
|
||||
TT_PT100, TT_INTERCOM. See list in temp.c.
|
||||
|
||||
The "additional" field is used for TT_THERMISTOR only. It defines the
|
||||
name of the table(s) in ThermistorTable.h to use. Typically, this is
|
||||
THERMISTOR_EXTRUDER for the first or only table, or THERMISTOR_BED for
|
||||
the second table. See also early in ThermistorTable.{single|double}.h.
|
||||
|
||||
For a GEN3 set temp_type to TT_INTERCOM and temp_pin to AIO0. The pin
|
||||
won't be used in this case.
|
||||
*/
|
||||
// name type pin additional
|
||||
//DEFINE_TEMP_SENSORS_START
|
||||
DEFINE_TEMP_SENSOR(extruder, TT_THERMISTOR, AIO7, THERMISTOR_EXTRUDER)
|
||||
DEFINE_TEMP_SENSOR(bed, TT_THERMISTOR, AIO6, THERMISTOR_BED)
|
||||
//DEFINE_TEMP_SENSORS_END
|
||||
|
||||
|
||||
/***************************************************************************\
|
||||
* *
|
||||
* 4. HEATERS *
|
||||
* *
|
||||
\***************************************************************************/
|
||||
|
||||
#ifndef DEFINE_HEATER
|
||||
#define DEFINE_HEATER(...)
|
||||
#endif
|
||||
|
||||
/** \def HEATER_PIN
|
||||
Heater pins a user should be able to choose from in configtool. All
|
||||
commented out.
|
||||
*/
|
||||
//#define HEATER_PIN DIO13
|
||||
//#define HEATER_PIN DIO14
|
||||
|
||||
/** \def DEFINE_HEATER
|
||||
Define your heaters and devices here.
|
||||
|
||||
To attach a heater to a temp sensor above, simply use exactly the same
|
||||
name - copy+paste is your friend. Some common names are 'extruder',
|
||||
'bed', 'fan', 'motor', ... names with special meaning can be found
|
||||
in gcode_process.c. Currently, these are:
|
||||
HEATER_extruder (M104)
|
||||
HEATER_bed (M140)
|
||||
HEATER_fan (M106)
|
||||
|
||||
Devices don't neccessarily have a temperature sensor, e.g. fans or
|
||||
milling spindles. Operate such devices by setting their power (M106),
|
||||
instead of setting their temperature (M104).
|
||||
|
||||
Also note, the index of a heater (M106 P#) can differ from the index of
|
||||
its attached temperature sensor (M104 P#) in case sensor-less devices
|
||||
are defined or the order of the definitions differs. The first defined
|
||||
device has the index 0 (zero).
|
||||
|
||||
Set 'pwm' to ...
|
||||
1 for using PWM on a PWM-able pin and on/off on other pins.
|
||||
0 for using on/off on a PWM-able pin, too.
|
||||
Using PWM usually gives smoother temperature control but can conflict
|
||||
with slow switches, like solid state relays. PWM frequency can be
|
||||
influenced globally with FAST_PWM, see below.
|
||||
*/
|
||||
// name port pwm
|
||||
//DEFINE_HEATERS_START
|
||||
DEFINE_HEATER(extruder, DIO13, 1)
|
||||
DEFINE_HEATER(bed, DIO14, 1)
|
||||
|
||||
#define HEATER_EXTRUDER HEATER_extruder
|
||||
#define HEATER_BED HEATER_bed
|
||||
//DEFINE_HEATERS_END
|
||||
|
||||
|
||||
/***************************************************************************\
|
||||
* *
|
||||
* 5. COMMUNICATION OPTIONS *
|
||||
* *
|
||||
\***************************************************************************/
|
||||
|
||||
/** \def BAUD
|
||||
Baud rate for the serial RS232 protocol connection to the host. Usually
|
||||
115200, other common values are 19200, 38400 or 57600. Ignored when USB_SERIAL
|
||||
is defined.
|
||||
*/
|
||||
#define BAUD 115200
|
||||
|
||||
/** \def XONXOFF
|
||||
Xon/Xoff flow control.
|
||||
|
||||
Redundant when using RepRap Host for sending G-code, but mandatory when
|
||||
sending G-code files with a plain terminal emulator, like GtkTerm (Linux),
|
||||
CoolTerm (Mac) or HyperTerminal (Windows).
|
||||
*/
|
||||
//#define XONXOFF
|
||||
|
||||
/** \def USB_SERIAL
|
||||
Define this for using USB instead of the serial RS232 protocol. Works on
|
||||
USB-equipped ATmegas, like the ATmega32U4, only.
|
||||
*/
|
||||
//#define USB_SERIAL
|
||||
|
|
@ -4,6 +4,7 @@ protectedFiles = [
|
|||
"board.gen7-v1.4.h",
|
||||
"board.ramps-v1.2.h",
|
||||
"board.ramps-v1.3.h",
|
||||
"board.sanguinololu-v1.1.h",
|
||||
"printer.mendel.h",
|
||||
"printer.wolfstrap.h"
|
||||
]
|
||||
|
|
|
|||
Loading…
Reference in New Issue