josh
/
Teacup_Firmware
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

STM32F411: cleaning mbed 

delete mbed-stm32f4xx_hal_
- dma.h
- flash.h
- legacy.h
- pwr.h
- uart.h

    SIZES          ARM...     stm32f411
    FLASH  :  3108 bytes           1%
    RAM    :   208 bytes           1%
    EEPROM :     0 bytes           0%
This commit is contained in:
Nico Tonnhofer 2015-11-12 23:22:14 +01:00
parent 3af3919303
commit eb8c5a39e1
18 changed files with 239 additions and 6535 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

2
Makefile-ARM
View File

@ -121,8 +121,6 @@ SOURCES = $(wildcard *.c)
ifeq ($(MCU), stm32f411)
SOURCES += mbed-system_stm32f4xx.c
SOURCES += mbed-stm32f4xx_hal.c
SOURCES += mbed-stm32f4xx_hal_cortex.c
SOURCES += mbed-stm32f4xx_hal_gpio.c
SOURCES += mbed-stm32f4xx_hal_rcc.c
SOURCES += mbed-stm32f4xx_hal_tim.c
SOURCES += mbed-cmsis_nvic_stm32.c

12
mbed-hal_tick_stm32.c
View File

@ -43,19 +43,19 @@ void us_ticker_irq_handler(void);
void timer_irq_handler(void) {
// Channel 1 for mbed timeout
if (__HAL_TIM_GET_ITSTATUS(&TimMasterHandle, TIM_IT_CC1) == SET) {
if (__HAL_TIM_GET_IT_SOURCE(&TimMasterHandle, TIM_IT_CC1) == SET) {
//us_ticker_irq_handler();
}
// Channel 2 for HAL tick
if (__HAL_TIM_GET_ITSTATUS(&TimMasterHandle, TIM_IT_CC2) == SET) {
if (__HAL_TIM_GET_IT_SOURCE(&TimMasterHandle, TIM_IT_CC2) == SET) {
__HAL_TIM_CLEAR_IT(&TimMasterHandle, TIM_IT_CC2);
uint32_t val = __HAL_TIM_GetCounter(&TimMasterHandle);
uint32_t val = __HAL_TIM_GET_COUNTER(&TimMasterHandle);
if ((val - PreviousVal) >= HAL_TICK_DELAY) {
// Increment HAL variable
HAL_IncTick();
// Prepare next interrupt
__HAL_TIM_SetCompare(&TimMasterHandle, TIM_CHANNEL_2, val + HAL_TICK_DELAY);
__HAL_TIM_SET_COMPARE(&TimMasterHandle, TIM_CHANNEL_2, val + HAL_TICK_DELAY);
PreviousVal = val;
#if 0 // For DEBUG only
HAL_GPIO_TogglePin(GPIOB, GPIO_PIN_6);
@ -93,8 +93,8 @@ HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority) {
// Channel 2 for HAL tick
HAL_TIM_OC_Start(&TimMasterHandle, TIM_CHANNEL_2);
PreviousVal = __HAL_TIM_GetCounter(&TimMasterHandle);
__HAL_TIM_SetCompare(&TimMasterHandle, TIM_CHANNEL_2, PreviousVal + HAL_TICK_DELAY);
PreviousVal = __HAL_TIM_GET_COUNTER(&TimMasterHandle);
__HAL_TIM_SET_COMPARE(&TimMasterHandle, TIM_CHANNEL_2, PreviousVal + HAL_TICK_DELAY);
__HAL_TIM_ENABLE_IT(&TimMasterHandle, TIM_IT_CC2);
#if 0 // For DEBUG only

6
mbed-hal_tick_stm32.h
View File

@ -44,10 +44,10 @@
#define TIM_MST TIM5
#define TIM_MST_IRQ TIM5_IRQn
#define TIM_MST_RCC __TIM5_CLK_ENABLE()
#define TIM_MST_RCC __HAL_RCC_TIM5_CLK_ENABLE()
#define TIM_MST_RESET_ON __TIM5_FORCE_RESET()
#define TIM_MST_RESET_OFF __TIM5_RELEASE_RESET()
#define TIM_MST_RESET_ON __HAL_RCC_TIM5_FORCE_RESET()
#define TIM_MST_RESET_OFF __HAL_RCC_TIM5_RELEASE_RESET()
#define HAL_TICK_DELAY (1000) // 1 ms

2510
mbed-stm32_hal_legacy.h
View File

File diff suppressed because it is too large Load Diff

12
mbed-stm32f4xx_hal.c
View File

@ -168,19 +168,19 @@ HAL_StatusTypeDef HAL_Init(void)
{
/* Configure Flash prefetch, Instruction cache, Data cache */
#if (INSTRUCTION_CACHE_ENABLE != 0)
__HAL_FLASH_INSTRUCTION_CACHE_ENABLE();
FLASH->ACR |= FLASH_ACR_ICEN;
#endif /* INSTRUCTION_CACHE_ENABLE */
#if (DATA_CACHE_ENABLE != 0)
__HAL_FLASH_DATA_CACHE_ENABLE();
FLASH->ACR |= FLASH_ACR_DCEN;
#endif /* DATA_CACHE_ENABLE */
#if (PREFETCH_ENABLE != 0)
__HAL_FLASH_PREFETCH_BUFFER_ENABLE();
FLASH->ACR |= FLASH_ACR_PRFTEN;
#endif /* PREFETCH_ENABLE */
/* Set Interrupt Group Priority */
HAL_NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_4);
NVIC_SetPriorityGrouping(0x00000003);
/* Use systick as time base source and configure 1ms tick (default clock after Reset is HSI) */
HAL_InitTick(TICK_INT_PRIORITY);
@ -263,10 +263,10 @@ __weak void HAL_MspDeInit(void)
__weak HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority)
{
/*Configure the SysTick to have interrupt in 1ms time basis*/
HAL_SYSTICK_Config(HAL_RCC_GetHCLKFreq()/1000);
SysTick_Config(HAL_RCC_GetHCLKFreq()/1000);
/*Configure the SysTick IRQ priority */
HAL_NVIC_SetPriority(SysTick_IRQn, TickPriority ,0);
NVIC_SetPriority(SysTick_IRQn, NVIC_EncodePriority(NVIC_GetPriorityGrouping(), TickPriority, 0));
/* Return function status */
return HAL_OK;

12
mbed-stm32f4xx_hal_conf.h
View File

@ -57,22 +57,22 @@
//#define HAL_CRYP_MODULE_ENABLED
//#define HAL_DAC_MODULE_ENABLED
//#define HAL_DCMI_MODULE_ENABLED
#define HAL_DMA_MODULE_ENABLED
//#define HAL_DMA_MODULE_ENABLED
/* #define HAL_DMA2D_MODULE_ENABLED */
//#define HAL_ETH_MODULE_ENABLED
#define HAL_FLASH_MODULE_ENABLED
//#define HAL_FLASH_MODULE_ENABLED
//#define HAL_NAND_MODULE_ENABLED
//#define HAL_NOR_MODULE_ENABLED
//#define HAL_PCCARD_MODULE_ENABLED
//#define HAL_SRAM_MODULE_ENABLED
/* #define HAL_SDRAM_MODULE_ENABLED */
//#define HAL_HASH_MODULE_ENABLED
#define HAL_GPIO_MODULE_ENABLED
//#define HAL_GPIO_MODULE_ENABLED
//#define HAL_I2C_MODULE_ENABLED
//#define HAL_I2S_MODULE_ENABLED
//#define HAL_IWDG_MODULE_ENABLED
//#define HAL_LTDC_MODULE_ENABLED
#define HAL_PWR_MODULE_ENABLED
//#define HAL_PWR_MODULE_ENABLED
#define HAL_RCC_MODULE_ENABLED
//#define HAL_RNG_MODULE_ENABLED
//#define HAL_RTC_MODULE_ENABLED
@ -80,12 +80,12 @@
//#define HAL_SD_MODULE_ENABLED
//#define HAL_SPI_MODULE_ENABLED
#define HAL_TIM_MODULE_ENABLED
#define HAL_UART_MODULE_ENABLED
//#define HAL_UART_MODULE_ENABLED
//#define HAL_USART_MODULE_ENABLED
//#define HAL_IRDA_MODULE_ENABLED
//#define HAL_SMARTCARD_MODULE_ENABLED
//#define HAL_WWDG_MODULE_ENABLED
#define HAL_CORTEX_MODULE_ENABLED
//#define HAL_CORTEX_MODULE_ENABLED
//#define HAL_PCD_MODULE_ENABLED
//#define HAL_HCD_MODULE_ENABLED

436
mbed-stm32f4xx_hal_cortex.c
View File

@ -1,436 +0,0 @@
/**
******************************************************************************
* @file stm32f4xx_hal_cortex.c
* @author MCD Application Team
* @version V1.3.2
* @date 26-June-2015
* @brief CORTEX HAL module driver.
* This file provides firmware functions to manage the following
* functionalities of the CORTEX:
* + Initialization and de-initialization functions
* + Peripheral Control functions
*
@verbatim
==============================================================================
##### How to use this driver #####
==============================================================================
[..]
*** How to configure Interrupts using CORTEX HAL driver ***
===========================================================
[..]
This section provides functions allowing to configure the NVIC interrupts (IRQ).
The Cortex-M4 exceptions are managed by CMSIS functions.
(#) Configure the NVIC Priority Grouping using HAL_NVIC_SetPriorityGrouping()
function according to the following table.
(#) Configure the priority of the selected IRQ Channels using HAL_NVIC_SetPriority().
(#) Enable the selected IRQ Channels using HAL_NVIC_EnableIRQ().
(#) please refer to programing manual for details in how to configure priority.
-@- When the NVIC_PRIORITYGROUP_0 is selected, IRQ preemption is no more possible.
The pending IRQ priority will be managed only by the sub priority.
-@- IRQ priority order (sorted by highest to lowest priority):
(+@) Lowest preemption priority
(+@) Lowest sub priority
(+@) Lowest hardware priority (IRQ number)
[..]
*** How to configure Systick using CORTEX HAL driver ***
========================================================
[..]
Setup SysTick Timer for time base.
(+) The HAL_SYSTICK_Config() function calls the SysTick_Config() function which
is a CMSIS function that:
(++) Configures the SysTick Reload register with value passed as function parameter.
(++) Configures the SysTick IRQ priority to the lowest value (0x0F).
(++) Resets the SysTick Counter register.
(++) Configures the SysTick Counter clock source to be Core Clock Source (HCLK).
(++) Enables the SysTick Interrupt.
(++) Starts the SysTick Counter.
(+) You can change the SysTick Clock source to be HCLK_Div8 by calling the macro
__HAL_CORTEX_SYSTICKCLK_CONFIG(SYSTICK_CLKSOURCE_HCLK_DIV8) just after the
HAL_SYSTICK_Config() function call. The __HAL_CORTEX_SYSTICKCLK_CONFIG() macro is defined
inside the stm32f4xx_hal_cortex.h file.
(+) You can change the SysTick IRQ priority by calling the
HAL_NVIC_SetPriority(SysTick_IRQn,...) function just after the HAL_SYSTICK_Config() function
call. The HAL_NVIC_SetPriority() call the NVIC_SetPriority() function which is a CMSIS function.
(+) To adjust the SysTick time base, use the following formula:
Reload Value = SysTick Counter Clock (Hz) x Desired Time base (s)
(++) Reload Value is the parameter to be passed for HAL_SYSTICK_Config() function
(++) Reload Value should not exceed 0xFFFFFF
@endverbatim
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "mbed-stm32f4xx_hal.h"
/** @addtogroup STM32F4xx_HAL_Driver
* @{
*/
/** @defgroup CORTEX CORTEX
* @brief CORTEX HAL module driver
* @{
*/
#ifdef HAL_CORTEX_MODULE_ENABLED
/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/
/* Private macros ------------------------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
/* Exported functions --------------------------------------------------------*/
/** @defgroup CORTEX_Exported_Functions CORTEX Exported Functions
* @{
*/
/** @defgroup CORTEX_Exported_Functions_Group1 Initialization and de-initialization functions
* @brief Initialization and Configuration functions
*
@verbatim
==============================================================================
##### Initialization and de-initialization functions #####
==============================================================================
[..]
This section provides the CORTEX HAL driver functions allowing to configure Interrupts
Systick functionalities
@endverbatim
* @{
*/
/**
* @brief Sets the priority grouping field (preemption priority and subpriority)
* using the required unlock sequence.
* @param PriorityGroup: The priority grouping bits length.
* This parameter can be one of the following values:
* @arg NVIC_PRIORITYGROUP_0: 0 bits for preemption priority
* 4 bits for subpriority
* @arg NVIC_PRIORITYGROUP_1: 1 bits for preemption priority
* 3 bits for subpriority
* @arg NVIC_PRIORITYGROUP_2: 2 bits for preemption priority
* 2 bits for subpriority
* @arg NVIC_PRIORITYGROUP_3: 3 bits for preemption priority
* 1 bits for subpriority
* @arg NVIC_PRIORITYGROUP_4: 4 bits for preemption priority
* 0 bits for subpriority
* @note When the NVIC_PriorityGroup_0 is selected, IRQ preemption is no more possible.
* The pending IRQ priority will be managed only by the subpriority.
* @retval None
*/
void HAL_NVIC_SetPriorityGrouping(uint32_t PriorityGroup)
{
/* Check the parameters */
assert_param(IS_NVIC_PRIORITY_GROUP(PriorityGroup));
/* Set the PRIGROUP[10:8] bits according to the PriorityGroup parameter value */
NVIC_SetPriorityGrouping(PriorityGroup);
}
/**
* @brief Sets the priority of an interrupt.
* @param IRQn: External interrupt number.
* This parameter can be an enumerator of IRQn_Type enumeration
* (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h))
* @param PreemptPriority: The preemption priority for the IRQn channel.
* This parameter can be a value between 0 and 15
* A lower priority value indicates a higher priority
* @param SubPriority: the subpriority level for the IRQ channel.
* This parameter can be a value between 0 and 15
* A lower priority value indicates a higher priority.
* @retval None
*/
void HAL_NVIC_SetPriority(IRQn_Type IRQn, uint32_t PreemptPriority, uint32_t SubPriority)
{
uint32_t prioritygroup = 0x00;
/* Check the parameters */
assert_param(IS_NVIC_SUB_PRIORITY(SubPriority));
assert_param(IS_NVIC_PREEMPTION_PRIORITY(PreemptPriority));
prioritygroup = NVIC_GetPriorityGrouping();
NVIC_SetPriority(IRQn, NVIC_EncodePriority(prioritygroup, PreemptPriority, SubPriority));
}
/**
* @brief Enables a device specific interrupt in the NVIC interrupt controller.
* @note To configure interrupts priority correctly, the NVIC_PriorityGroupConfig()
* function should be called before.
* @param IRQn External interrupt number.
* This parameter can be an enumerator of IRQn_Type enumeration
* (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h))
* @retval None
*/
void HAL_NVIC_EnableIRQ(IRQn_Type IRQn)
{
/* Check the parameters */
assert_param(IS_NVIC_DEVICE_IRQ(IRQn));
/* Enable interrupt */
NVIC_EnableIRQ(IRQn);
}
/**
* @brief Disables a device specific interrupt in the NVIC interrupt controller.
* @param IRQn External interrupt number.
* This parameter can be an enumerator of IRQn_Type enumeration
* (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h))
* @retval None
*/
void HAL_NVIC_DisableIRQ(IRQn_Type IRQn)
{
/* Check the parameters */
assert_param(IS_NVIC_DEVICE_IRQ(IRQn));
/* Disable interrupt */
NVIC_DisableIRQ(IRQn);
}
/**
* @brief Initiates a system reset request to reset the MCU.
* @retval None
*/
void HAL_NVIC_SystemReset(void)
{
/* System Reset */
NVIC_SystemReset();
}
/**
* @brief Initializes the System Timer and its interrupt, and starts the System Tick Timer.
* Counter is in free running mode to generate periodic interrupts.
* @param TicksNumb: Specifies the ticks Number of ticks between two interrupts.
* @retval status: - 0 Function succeeded.
* - 1 Function failed.
*/
uint32_t HAL_SYSTICK_Config(uint32_t TicksNumb)
{
return SysTick_Config(TicksNumb);
}
/**
* @}
*/
/** @defgroup CORTEX_Exported_Functions_Group2 Peripheral Control functions
* @brief Cortex control functions
*
@verbatim
==============================================================================
##### Peripheral Control functions #####
==============================================================================
[..]
This subsection provides a set of functions allowing to control the CORTEX
(NVIC, SYSTICK) functionalities.
@endverbatim
* @{
*/
/**
* @brief Gets the priority grouping field from the NVIC Interrupt Controller.
* @retval Priority grouping field (SCB->AIRCR [10:8] PRIGROUP field)
*/
uint32_t HAL_NVIC_GetPriorityGrouping(void)
{
/* Get the PRIGROUP[10:8] field value */
return NVIC_GetPriorityGrouping();
}
/**
* @brief Gets the priority of an interrupt.
* @param IRQn: External interrupt number.
* This parameter can be an enumerator of IRQn_Type enumeration
* (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h))
* @param PriorityGroup: the priority grouping bits length.
* This parameter can be one of the following values:
* @arg NVIC_PRIORITYGROUP_0: 0 bits for preemption priority
* 4 bits for subpriority
* @arg NVIC_PRIORITYGROUP_1: 1 bits for preemption priority
* 3 bits for subpriority
* @arg NVIC_PRIORITYGROUP_2: 2 bits for preemption priority
* 2 bits for subpriority
* @arg NVIC_PRIORITYGROUP_3: 3 bits for preemption priority
* 1 bits for subpriority
* @arg NVIC_PRIORITYGROUP_4: 4 bits for preemption priority
* 0 bits for subpriority
* @param pPreemptPriority: Pointer on the Preemptive priority value (starting from 0).
* @param pSubPriority: Pointer on the Subpriority value (starting from 0).
* @retval None
*/
void HAL_NVIC_GetPriority(IRQn_Type IRQn, uint32_t PriorityGroup, uint32_t *pPreemptPriority, uint32_t *pSubPriority)
{
/* Check the parameters */
assert_param(IS_NVIC_PRIORITY_GROUP(PriorityGroup));
/* Get priority for Cortex-M system or device specific interrupts */
NVIC_DecodePriority(NVIC_GetPriority(IRQn), PriorityGroup, pPreemptPriority, pSubPriority);
}
/**
* @brief Sets Pending bit of an external interrupt.
* @param IRQn External interrupt number
* This parameter can be an enumerator of IRQn_Type enumeration
* (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h))
* @retval None
*/
void HAL_NVIC_SetPendingIRQ(IRQn_Type IRQn)
{
/* Check the parameters */
assert_param(IS_NVIC_DEVICE_IRQ(IRQn));
/* Set interrupt pending */
NVIC_SetPendingIRQ(IRQn);
}
/**
* @brief Gets Pending Interrupt (reads the pending register in the NVIC
* and returns the pending bit for the specified interrupt).
* @param IRQn External interrupt number.
* This parameter can be an enumerator of IRQn_Type enumeration
* (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h))
* @retval status: - 0 Interrupt status is not pending.
* - 1 Interrupt status is pending.
*/
uint32_t HAL_NVIC_GetPendingIRQ(IRQn_Type IRQn)
{
/* Check the parameters */
assert_param(IS_NVIC_DEVICE_IRQ(IRQn));
/* Return 1 if pending else 0 */
return NVIC_GetPendingIRQ(IRQn);
}
/**
* @brief Clears the pending bit of an external interrupt.
* @param IRQn External interrupt number.
* This parameter can be an enumerator of IRQn_Type enumeration
* (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h))
* @retval None
*/
void HAL_NVIC_ClearPendingIRQ(IRQn_Type IRQn)
{
/* Check the parameters */
assert_param(IS_NVIC_DEVICE_IRQ(IRQn));
/* Clear pending interrupt */
NVIC_ClearPendingIRQ(IRQn);
}
/**
* @brief Gets active interrupt ( reads the active register in NVIC and returns the active bit).
* @param IRQn External interrupt number
* This parameter can be an enumerator of IRQn_Type enumeration
* (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h))
* @retval status: - 0 Interrupt status is not pending.
* - 1 Interrupt status is pending.
*/
uint32_t HAL_NVIC_GetActive(IRQn_Type IRQn)
{
/* Check the parameters */
assert_param(IS_NVIC_DEVICE_IRQ(IRQn));
/* Return 1 if active else 0 */
return NVIC_GetActive(IRQn);
}
/**
* @brief Configures the SysTick clock source.
* @param CLKSource: specifies the SysTick clock source.
* This parameter can be one of the following values:
* @arg SYSTICK_CLKSOURCE_HCLK_DIV8: AHB clock divided by 8 selected as SysTick clock source.
* @arg SYSTICK_CLKSOURCE_HCLK: AHB clock selected as SysTick clock source.
* @retval None
*/
void HAL_SYSTICK_CLKSourceConfig(uint32_t CLKSource)
{
/* Check the parameters */
assert_param(IS_SYSTICK_CLK_SOURCE(CLKSource));
if (CLKSource == SYSTICK_CLKSOURCE_HCLK)
{
SysTick->CTRL |= SYSTICK_CLKSOURCE_HCLK;
}
else
{
SysTick->CTRL &= ~SYSTICK_CLKSOURCE_HCLK;
}
}
/**
* @brief This function handles SYSTICK interrupt request.
* @retval None
*/
void HAL_SYSTICK_IRQHandler(void)
{
HAL_SYSTICK_Callback();
}
/**
* @brief SYSTICK callback.
* @retval None
*/
__weak void HAL_SYSTICK_Callback(void)
{
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_SYSTICK_Callback could be implemented in the user file
*/
}
/**
* @}
*/
/**
* @}
*/
#endif /* HAL_CORTEX_MODULE_ENABLED */
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

200
mbed-stm32f4xx_hal_cortex.h
View File

@ -1,200 +0,0 @@
/**
******************************************************************************
* @file stm32f4xx_hal_cortex.h
* @author MCD Application Team
* @version V1.3.2
* @date 26-June-2015
* @brief Header file of CORTEX HAL module.
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F4xx_HAL_CORTEX_H
#define __STM32F4xx_HAL_CORTEX_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "mbed-stm32f4xx_hal_def.h"
/** @addtogroup STM32F4xx_HAL_Driver
* @{
*/
/** @addtogroup CORTEX
* @{
*/
/* Exported types ------------------------------------------------------------*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup CORTEX_Exported_Constants CORTEX Exported Constants
* @{
*/
/** @defgroup CORTEX_Preemption_Priority_Group CORTEX Preemption Priority Group
* @{
*/
#define NVIC_PRIORITYGROUP_0 ((uint32_t)0x00000007) /*!< 0 bits for pre-emption priority
4 bits for subpriority */
#define NVIC_PRIORITYGROUP_1 ((uint32_t)0x00000006) /*!< 1 bits for pre-emption priority
3 bits for subpriority */
#define NVIC_PRIORITYGROUP_2 ((uint32_t)0x00000005) /*!< 2 bits for pre-emption priority
2 bits for subpriority */
#define NVIC_PRIORITYGROUP_3 ((uint32_t)0x00000004) /*!< 3 bits for pre-emption priority
1 bits for subpriority */
#define NVIC_PRIORITYGROUP_4 ((uint32_t)0x00000003) /*!< 4 bits for pre-emption priority
0 bits for subpriority */
/**
* @}
*/
/** @defgroup CORTEX_SysTick_clock_source CORTEX _SysTick clock source
* @{
*/
#define SYSTICK_CLKSOURCE_HCLK_DIV8 ((uint32_t)0x00000000)
#define SYSTICK_CLKSOURCE_HCLK ((uint32_t)0x00000004)
/**
* @}
*/
/**
* @}
*/
/* Exported Macros -----------------------------------------------------------*/
/** @defgroup CORTEX_Exported_Macros CORTEX Exported Macros
* @{
*/
/** @brief Configures the SysTick clock source.
* @param __CLKSRC__: specifies the SysTick clock source.
* This parameter can be one of the following values:
* @arg SYSTICK_CLKSOURCE_HCLK_DIV8: AHB clock divided by 8 selected as SysTick clock source.
* @arg SYSTICK_CLKSOURCE_HCLK: AHB clock selected as SysTick clock source.
* @retval None
*/
#define __HAL_CORTEX_SYSTICKCLK_CONFIG(__CLKSRC__) \
do { \
if ((__CLKSRC__) == SYSTICK_CLKSOURCE_HCLK) \
{ \
SysTick->CTRL |= SYSTICK_CLKSOURCE_HCLK; \
} \
else \
SysTick->CTRL &= ~SYSTICK_CLKSOURCE_HCLK; \
} while(0)
/**
* @}
*/
/* Exported functions --------------------------------------------------------*/
/** @addtogroup CORTEX_Exported_Functions
* @{
*/
/** @addtogroup CORTEX_Exported_Functions_Group1
* @{
*/
/* Initialization and de-initialization functions *****************************/
void HAL_NVIC_SetPriorityGrouping(uint32_t PriorityGroup);
void HAL_NVIC_SetPriority(IRQn_Type IRQn, uint32_t PreemptPriority, uint32_t SubPriority);
void HAL_NVIC_EnableIRQ(IRQn_Type IRQn);
void HAL_NVIC_DisableIRQ(IRQn_Type IRQn);
void HAL_NVIC_SystemReset(void);
uint32_t HAL_SYSTICK_Config(uint32_t TicksNumb);
/**
* @}
*/
/** @addtogroup CORTEX_Exported_Functions_Group2
* @{
*/
/* Peripheral Control functions ***********************************************/
uint32_t HAL_NVIC_GetPriorityGrouping(void);
void HAL_NVIC_GetPriority(IRQn_Type IRQn, uint32_t PriorityGroup, uint32_t* pPreemptPriority, uint32_t* pSubPriority);
uint32_t HAL_NVIC_GetPendingIRQ(IRQn_Type IRQn);
void HAL_NVIC_SetPendingIRQ(IRQn_Type IRQn);
void HAL_NVIC_ClearPendingIRQ(IRQn_Type IRQn);
uint32_t HAL_NVIC_GetActive(IRQn_Type IRQn);
void HAL_SYSTICK_CLKSourceConfig(uint32_t CLKSource);
void HAL_SYSTICK_IRQHandler(void);
void HAL_SYSTICK_Callback(void);
/**
* @}
*/
/**
* @}
*/
/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/
/* Private macros ------------------------------------------------------------*/
/** @defgroup CORTEX_Private_Macros CORTEX Private Macros
* @{
*/
#define IS_NVIC_PRIORITY_GROUP(GROUP) (((GROUP) == NVIC_PRIORITYGROUP_0) || \
((GROUP) == NVIC_PRIORITYGROUP_1) || \
((GROUP) == NVIC_PRIORITYGROUP_2) || \
((GROUP) == NVIC_PRIORITYGROUP_3) || \
((GROUP) == NVIC_PRIORITYGROUP_4))
#define IS_NVIC_PREEMPTION_PRIORITY(PRIORITY) ((PRIORITY) < 0x10)
#define IS_NVIC_SUB_PRIORITY(PRIORITY) ((PRIORITY) < 0x10)
#define IS_NVIC_DEVICE_IRQ(IRQ) ((IRQ) >= 0x00)
#define IS_SYSTICK_CLK_SOURCE(SOURCE) (((SOURCE) == SYSTICK_CLKSOURCE_HCLK) || \
((SOURCE) == SYSTICK_CLKSOURCE_HCLK_DIV8))
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* __STM32F4xx_HAL_CORTEX_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

148
mbed-stm32f4xx_hal_def.h
View File

@ -43,14 +43,11 @@
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "mbed-stm32f4xx.h"
#include "mbed-stm32_hal_legacy.h"
#include "arduino_stm32f411.h"
#include <stdio.h>
/* Exported types ------------------------------------------------------------*/
/**
* @brief HAL Status structures definition
*/
@ -71,6 +68,149 @@ typedef enum
HAL_LOCKED = 0x01
} HAL_LockTypeDef;
/*
Old mbed-stm32f4xx_hal_gpio.h
**/
/**
* @brief GPIO Init structure definition
*/
typedef struct
{
uint32_t Pin; /*!< Specifies the GPIO pins to be configured.
This parameter can be any value of @ref GPIO_pins_define */
uint32_t Mode; /*!< Specifies the operating mode for the selected pins.
This parameter can be a value of @ref GPIO_mode_define */
uint32_t Pull; /*!< Specifies the Pull-up or Pull-Down activation for the selected pins.
This parameter can be a value of @ref GPIO_pull_define */
uint32_t Speed; /*!< Specifies the speed for the selected pins.
This parameter can be a value of @ref GPIO_speed_define */
uint32_t Alternate; /*!< Peripheral to be connected to the selected pins.
This parameter can be a value of @ref GPIO_Alternate_function_selection */
}GPIO_InitTypeDef;
/**
* @brief GPIO Bit SET and Bit RESET enumeration
*/
typedef enum
{
GPIO_PIN_RESET = 0,
GPIO_PIN_SET
}GPIO_PinState;
/* End gpio */
/*
Old mbed-stm32f4xx_hal_dma.h
**/
typedef struct
{
uint32_t Channel; /*!< Specifies the channel used for the specified stream.
This parameter can be a value of @ref DMA_Channel_selection */
uint32_t Direction; /*!< Specifies if the data will be transferred from memory to peripheral,
from memory to memory or from peripheral to memory.
This parameter can be a value of @ref DMA_Data_transfer_direction */
uint32_t PeriphInc; /*!< Specifies whether the Peripheral address register should be incremented or not.
This parameter can be a value of @ref DMA_Peripheral_incremented_mode */
uint32_t MemInc; /*!< Specifies whether the memory address register should be incremented or not.
This parameter can be a value of @ref DMA_Memory_incremented_mode */
uint32_t PeriphDataAlignment; /*!< Specifies the Peripheral data width.
This parameter can be a value of @ref DMA_Peripheral_data_size */
uint32_t MemDataAlignment; /*!< Specifies the Memory data width.
This parameter can be a value of @ref DMA_Memory_data_size */
uint32_t Mode; /*!< Specifies the operation mode of the DMAy Streamx.
This parameter can be a value of @ref DMA_mode
@note The circular buffer mode cannot be used if the memory-to-memory
data transfer is configured on the selected Stream */
uint32_t Priority; /*!< Specifies the software priority for the DMAy Streamx.
This parameter can be a value of @ref DMA_Priority_level */
uint32_t FIFOMode; /*!< Specifies if the FIFO mode or Direct mode will be used for the specified stream.
This parameter can be a value of @ref DMA_FIFO_direct_mode
@note The Direct mode (FIFO mode disabled) cannot be used if the
memory-to-memory data transfer is configured on the selected stream */
uint32_t FIFOThreshold; /*!< Specifies the FIFO threshold level.
This parameter can be a value of @ref DMA_FIFO_threshold_level */
uint32_t MemBurst; /*!< Specifies the Burst transfer configuration for the memory transfers.
It specifies the amount of data to be transferred in a single non interruptible
transaction.
This parameter can be a value of @ref DMA_Memory_burst
@note The burst mode is possible only if the address Increment mode is enabled. */
uint32_t PeriphBurst; /*!< Specifies the Burst transfer configuration for the peripheral transfers.
It specifies the amount of data to be transferred in a single non interruptable
transaction.
This parameter can be a value of @ref DMA_Peripheral_burst
@note The burst mode is possible only if the address Increment mode is enabled. */
}DMA_InitTypeDef;
/**
* @brief HAL DMA State structures definition
*/
typedef enum
{
HAL_DMA_STATE_RESET = 0x00, /*!< DMA not yet initialized or disabled */
HAL_DMA_STATE_READY = 0x01, /*!< DMA initialized and ready for use */
HAL_DMA_STATE_READY_MEM0 = 0x11, /*!< DMA Mem0 process success */
HAL_DMA_STATE_READY_MEM1 = 0x21, /*!< DMA Mem1 process success */
HAL_DMA_STATE_READY_HALF_MEM0 = 0x31, /*!< DMA Mem0 Half process success */
HAL_DMA_STATE_READY_HALF_MEM1 = 0x41, /*!< DMA Mem1 Half process success */
HAL_DMA_STATE_BUSY = 0x02, /*!< DMA process is ongoing */
HAL_DMA_STATE_BUSY_MEM0 = 0x12, /*!< DMA Mem0 process is ongoing */
HAL_DMA_STATE_BUSY_MEM1 = 0x22, /*!< DMA Mem1 process is ongoing */
HAL_DMA_STATE_TIMEOUT = 0x03, /*!< DMA timeout state */
HAL_DMA_STATE_ERROR = 0x04, /*!< DMA error state */
}HAL_DMA_StateTypeDef;
/* Exported functions --------------------------------------------------------*/
/** @addtogroup UART_Exported_Functions
* @{
*/
typedef struct __DMA_HandleTypeDef
{
DMA_Stream_TypeDef *Instance; /*!< Register base address */
DMA_InitTypeDef Init; /*!< DMA communication parameters */
HAL_LockTypeDef Lock; /*!< DMA locking object */
__IO HAL_DMA_StateTypeDef State; /*!< DMA transfer state */
void *Parent; /*!< Parent object state */
void (* XferCpltCallback)( struct __DMA_HandleTypeDef * hdma); /*!< DMA transfer complete callback */
void (* XferHalfCpltCallback)( struct __DMA_HandleTypeDef * hdma); /*!< DMA Half transfer complete callback */
void (* XferM1CpltCallback)( struct __DMA_HandleTypeDef * hdma); /*!< DMA transfer complete Memory1 callback */
void (* XferErrorCallback)( struct __DMA_HandleTypeDef * hdma); /*!< DMA transfer error callback */
__IO uint32_t ErrorCode; /*!< DMA Error code */
}DMA_HandleTypeDef;
HAL_StatusTypeDef HAL_DMA_Start (DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength);
HAL_StatusTypeDef HAL_DMA_Start_IT(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength);
HAL_StatusTypeDef HAL_DMA_Abort(DMA_HandleTypeDef *hdma);
HAL_StatusTypeDef HAL_DMA_PollForTransfer(DMA_HandleTypeDef *hdma, uint32_t CompleteLevel, uint32_t Timeout);
/* End of old dma */
/* Exported types ------------------------------------------------------------*/
/* Exported macro ------------------------------------------------------------*/
#define HAL_MAX_DELAY 0xFFFFFFFF

767
mbed-stm32f4xx_hal_dma.h
View File

@ -1,767 +0,0 @@
/**
******************************************************************************
* @file stm32f4xx_hal_dma.h
* @author MCD Application Team
* @version V1.3.2
* @date 26-June-2015
* @brief Header file of DMA HAL module.
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F4xx_HAL_DMA_H
#define __STM32F4xx_HAL_DMA_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "mbed-stm32f4xx_hal_def.h"
/** @addtogroup STM32F4xx_HAL_Driver
* @{
*/
/** @addtogroup DMA
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup DMA_Exported_Types DMA Exported Types
* @brief DMA Exported Types
* @{
*/
/**
* @brief DMA Configuration Structure definition
*/
typedef struct
{
uint32_t Channel; /*!< Specifies the channel used for the specified stream.
This parameter can be a value of @ref DMA_Channel_selection */
uint32_t Direction; /*!< Specifies if the data will be transferred from memory to peripheral,
from memory to memory or from peripheral to memory.
This parameter can be a value of @ref DMA_Data_transfer_direction */
uint32_t PeriphInc; /*!< Specifies whether the Peripheral address register should be incremented or not.
This parameter can be a value of @ref DMA_Peripheral_incremented_mode */
uint32_t MemInc; /*!< Specifies whether the memory address register should be incremented or not.
This parameter can be a value of @ref DMA_Memory_incremented_mode */
uint32_t PeriphDataAlignment; /*!< Specifies the Peripheral data width.
This parameter can be a value of @ref DMA_Peripheral_data_size */
uint32_t MemDataAlignment; /*!< Specifies the Memory data width.
This parameter can be a value of @ref DMA_Memory_data_size */
uint32_t Mode; /*!< Specifies the operation mode of the DMAy Streamx.
This parameter can be a value of @ref DMA_mode
@note The circular buffer mode cannot be used if the memory-to-memory
data transfer is configured on the selected Stream */
uint32_t Priority; /*!< Specifies the software priority for the DMAy Streamx.
This parameter can be a value of @ref DMA_Priority_level */
uint32_t FIFOMode; /*!< Specifies if the FIFO mode or Direct mode will be used for the specified stream.
This parameter can be a value of @ref DMA_FIFO_direct_mode
@note The Direct mode (FIFO mode disabled) cannot be used if the
memory-to-memory data transfer is configured on the selected stream */
uint32_t FIFOThreshold; /*!< Specifies the FIFO threshold level.
This parameter can be a value of @ref DMA_FIFO_threshold_level */
uint32_t MemBurst; /*!< Specifies the Burst transfer configuration for the memory transfers.
It specifies the amount of data to be transferred in a single non interruptible
transaction.
This parameter can be a value of @ref DMA_Memory_burst
@note The burst mode is possible only if the address Increment mode is enabled. */
uint32_t PeriphBurst; /*!< Specifies the Burst transfer configuration for the peripheral transfers.
It specifies the amount of data to be transferred in a single non interruptable
transaction.
This parameter can be a value of @ref DMA_Peripheral_burst
@note The burst mode is possible only if the address Increment mode is enabled. */
}DMA_InitTypeDef;
/**
* @brief HAL DMA State structures definition
*/
typedef enum
{
HAL_DMA_STATE_RESET = 0x00, /*!< DMA not yet initialized or disabled */
HAL_DMA_STATE_READY = 0x01, /*!< DMA initialized and ready for use */
HAL_DMA_STATE_READY_MEM0 = 0x11, /*!< DMA Mem0 process success */
HAL_DMA_STATE_READY_MEM1 = 0x21, /*!< DMA Mem1 process success */
HAL_DMA_STATE_READY_HALF_MEM0 = 0x31, /*!< DMA Mem0 Half process success */
HAL_DMA_STATE_READY_HALF_MEM1 = 0x41, /*!< DMA Mem1 Half process success */
HAL_DMA_STATE_BUSY = 0x02, /*!< DMA process is ongoing */
HAL_DMA_STATE_BUSY_MEM0 = 0x12, /*!< DMA Mem0 process is ongoing */
HAL_DMA_STATE_BUSY_MEM1 = 0x22, /*!< DMA Mem1 process is ongoing */
HAL_DMA_STATE_TIMEOUT = 0x03, /*!< DMA timeout state */
HAL_DMA_STATE_ERROR = 0x04, /*!< DMA error state */
}HAL_DMA_StateTypeDef;
/**
* @brief HAL DMA Error Code structure definition
*/
typedef enum
{
HAL_DMA_FULL_TRANSFER = 0x00, /*!< Full transfer */
HAL_DMA_HALF_TRANSFER = 0x01, /*!< Half Transfer */
}HAL_DMA_LevelCompleteTypeDef;
/**
* @brief DMA handle Structure definition
*/
typedef struct __DMA_HandleTypeDef
{
DMA_Stream_TypeDef *Instance; /*!< Register base address */
DMA_InitTypeDef Init; /*!< DMA communication parameters */
HAL_LockTypeDef Lock; /*!< DMA locking object */
__IO HAL_DMA_StateTypeDef State; /*!< DMA transfer state */
void *Parent; /*!< Parent object state */
void (* XferCpltCallback)( struct __DMA_HandleTypeDef * hdma); /*!< DMA transfer complete callback */
void (* XferHalfCpltCallback)( struct __DMA_HandleTypeDef * hdma); /*!< DMA Half transfer complete callback */
void (* XferM1CpltCallback)( struct __DMA_HandleTypeDef * hdma); /*!< DMA transfer complete Memory1 callback */
void (* XferErrorCallback)( struct __DMA_HandleTypeDef * hdma); /*!< DMA transfer error callback */
__IO uint32_t ErrorCode; /*!< DMA Error code */
}DMA_HandleTypeDef;
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup DMA_Exported_Constants DMA Exported Constants
* @brief DMA Exported constants
* @{
*/
/** @defgroup DMA_Error_Code DMA Error Code
* @brief DMA Error Code
* @{
*/
#define HAL_DMA_ERROR_NONE ((uint32_t)0x00000000) /*!< No error */
#define HAL_DMA_ERROR_TE ((uint32_t)0x00000001) /*!< Transfer error */
#define HAL_DMA_ERROR_FE ((uint32_t)0x00000002) /*!< FIFO error */
#define HAL_DMA_ERROR_DME ((uint32_t)0x00000004) /*!< Direct Mode error */
#define HAL_DMA_ERROR_TIMEOUT ((uint32_t)0x00000020) /*!< Timeout error */
/**
* @}
*/
/** @defgroup DMA_Channel_selection DMA Channel selection
* @brief DMA channel selection
* @{
*/
#define DMA_CHANNEL_0 ((uint32_t)0x00000000) /*!< DMA Channel 0 */
#define DMA_CHANNEL_1 ((uint32_t)0x02000000) /*!< DMA Channel 1 */
#define DMA_CHANNEL_2 ((uint32_t)0x04000000) /*!< DMA Channel 2 */
#define DMA_CHANNEL_3 ((uint32_t)0x06000000) /*!< DMA Channel 3 */
#define DMA_CHANNEL_4 ((uint32_t)0x08000000) /*!< DMA Channel 4 */
#define DMA_CHANNEL_5 ((uint32_t)0x0A000000) /*!< DMA Channel 5 */
#define DMA_CHANNEL_6 ((uint32_t)0x0C000000) /*!< DMA Channel 6 */
#define DMA_CHANNEL_7 ((uint32_t)0x0E000000) /*!< DMA Channel 7 */
/**
* @}
*/
/** @defgroup DMA_Data_transfer_direction DMA Data transfer direction
* @brief DMA data transfer direction
* @{
*/
#define DMA_PERIPH_TO_MEMORY ((uint32_t)0x00000000) /*!< Peripheral to memory direction */
#define DMA_MEMORY_TO_PERIPH ((uint32_t)DMA_SxCR_DIR_0) /*!< Memory to peripheral direction */
#define DMA_MEMORY_TO_MEMORY ((uint32_t)DMA_SxCR_DIR_1) /*!< Memory to memory direction */
/**
* @}
*/
/** @defgroup DMA_Peripheral_incremented_mode DMA Peripheral incremented mode
* @brief DMA peripheral incremented mode
* @{
*/
#define DMA_PINC_ENABLE ((uint32_t)DMA_SxCR_PINC) /*!< Peripheral increment mode enable */
#define DMA_PINC_DISABLE ((uint32_t)0x00000000) /*!< Peripheral increment mode disable */
/**
* @}
*/
/** @defgroup DMA_Memory_incremented_mode DMA Memory incremented mode
* @brief DMA memory incremented mode
* @{
*/
#define DMA_MINC_ENABLE ((uint32_t)DMA_SxCR_MINC) /*!< Memory increment mode enable */
#define DMA_MINC_DISABLE ((uint32_t)0x00000000) /*!< Memory increment mode disable */
/**
* @}
*/
/** @defgroup DMA_Peripheral_data_size DMA Peripheral data size
* @brief DMA peripheral data size
* @{
*/
#define DMA_PDATAALIGN_BYTE ((uint32_t)0x00000000) /*!< Peripheral data alignment: Byte */
#define DMA_PDATAALIGN_HALFWORD ((uint32_t)DMA_SxCR_PSIZE_0) /*!< Peripheral data alignment: HalfWord */
#define DMA_PDATAALIGN_WORD ((uint32_t)DMA_SxCR_PSIZE_1) /*!< Peripheral data alignment: Word */
/**
* @}
*/
/** @defgroup DMA_Memory_data_size DMA Memory data size
* @brief DMA memory data size
* @{
*/
#define DMA_MDATAALIGN_BYTE ((uint32_t)0x00000000) /*!< Memory data alignment: Byte */
#define DMA_MDATAALIGN_HALFWORD ((uint32_t)DMA_SxCR_MSIZE_0) /*!< Memory data alignment: HalfWord */
#define DMA_MDATAALIGN_WORD ((uint32_t)DMA_SxCR_MSIZE_1) /*!< Memory data alignment: Word */
/**
* @}
*/
/** @defgroup DMA_mode DMA mode
* @brief DMA mode
* @{
*/
#define DMA_NORMAL ((uint32_t)0x00000000) /*!< Normal mode */
#define DMA_CIRCULAR ((uint32_t)DMA_SxCR_CIRC) /*!< Circular mode */
#define DMA_PFCTRL ((uint32_t)DMA_SxCR_PFCTRL) /*!< Peripheral flow control mode */
/**
* @}
*/
/** @defgroup DMA_Priority_level DMA Priority level
* @brief DMA priority levels
* @{
*/
#define DMA_PRIORITY_LOW ((uint32_t)0x00000000) /*!< Priority level: Low */
#define DMA_PRIORITY_MEDIUM ((uint32_t)DMA_SxCR_PL_0) /*!< Priority level: Medium */
#define DMA_PRIORITY_HIGH ((uint32_t)DMA_SxCR_PL_1) /*!< Priority level: High */
#define DMA_PRIORITY_VERY_HIGH ((uint32_t)DMA_SxCR_PL) /*!< Priority level: Very High */
/**
* @}
*/
/** @defgroup DMA_FIFO_direct_mode DMA FIFO direct mode
* @brief DMA FIFO direct mode
* @{
*/
#define DMA_FIFOMODE_DISABLE ((uint32_t)0x00000000) /*!< FIFO mode disable */
#define DMA_FIFOMODE_ENABLE ((uint32_t)DMA_SxFCR_DMDIS) /*!< FIFO mode enable */
/**
* @}
*/
/** @defgroup DMA_FIFO_threshold_level DMA FIFO threshold level
* @brief DMA FIFO level
* @{
*/
#define DMA_FIFO_THRESHOLD_1QUARTERFULL ((uint32_t)0x00000000) /*!< FIFO threshold 1 quart full configuration */
#define DMA_FIFO_THRESHOLD_HALFFULL ((uint32_t)DMA_SxFCR_FTH_0) /*!< FIFO threshold half full configuration */
#define DMA_FIFO_THRESHOLD_3QUARTERSFULL ((uint32_t)DMA_SxFCR_FTH_1) /*!< FIFO threshold 3 quarts full configuration */
#define DMA_FIFO_THRESHOLD_FULL ((uint32_t)DMA_SxFCR_FTH) /*!< FIFO threshold full configuration */
/**
* @}
*/
/** @defgroup DMA_Memory_burst DMA Memory burst
* @brief DMA memory burst
* @{
*/
#define DMA_MBURST_SINGLE ((uint32_t)0x00000000)
#define DMA_MBURST_INC4 ((uint32_t)DMA_SxCR_MBURST_0)
#define DMA_MBURST_INC8 ((uint32_t)DMA_SxCR_MBURST_1)
#define DMA_MBURST_INC16 ((uint32_t)DMA_SxCR_MBURST)
/**
* @}
*/
/** @defgroup DMA_Peripheral_burst DMA Peripheral burst
* @brief DMA peripheral burst
* @{
*/
#define DMA_PBURST_SINGLE ((uint32_t)0x00000000)
#define DMA_PBURST_INC4 ((uint32_t)DMA_SxCR_PBURST_0)
#define DMA_PBURST_INC8 ((uint32_t)DMA_SxCR_PBURST_1)
#define DMA_PBURST_INC16 ((uint32_t)DMA_SxCR_PBURST)
/**
* @}
*/
/** @defgroup DMA_interrupt_enable_definitions DMA interrupt enable definitions
* @brief DMA interrupts definition
* @{
*/
#define DMA_IT_TC ((uint32_t)DMA_SxCR_TCIE)
#define DMA_IT_HT ((uint32_t)DMA_SxCR_HTIE)
#define DMA_IT_TE ((uint32_t)DMA_SxCR_TEIE)
#define DMA_IT_DME ((uint32_t)DMA_SxCR_DMEIE)
#define DMA_IT_FE ((uint32_t)0x00000080)
/**
* @}
*/
/** @defgroup DMA_flag_definitions DMA flag definitions
* @brief DMA flag definitions
* @{
*/
#define DMA_FLAG_FEIF0_4 ((uint32_t)0x00800001)
#define DMA_FLAG_DMEIF0_4 ((uint32_t)0x00800004)
#define DMA_FLAG_TEIF0_4 ((uint32_t)0x00000008)
#define DMA_FLAG_HTIF0_4 ((uint32_t)0x00000010)
#define DMA_FLAG_TCIF0_4 ((uint32_t)0x00000020)
#define DMA_FLAG_FEIF1_5 ((uint32_t)0x00000040)
#define DMA_FLAG_DMEIF1_5 ((uint32_t)0x00000100)
#define DMA_FLAG_TEIF1_5 ((uint32_t)0x00000200)
#define DMA_FLAG_HTIF1_5 ((uint32_t)0x00000400)
#define DMA_FLAG_TCIF1_5 ((uint32_t)0x00000800)
#define DMA_FLAG_FEIF2_6 ((uint32_t)0x00010000)
#define DMA_FLAG_DMEIF2_6 ((uint32_t)0x00040000)
#define DMA_FLAG_TEIF2_6 ((uint32_t)0x00080000)
#define DMA_FLAG_HTIF2_6 ((uint32_t)0x00100000)
#define DMA_FLAG_TCIF2_6 ((uint32_t)0x00200000)
#define DMA_FLAG_FEIF3_7 ((uint32_t)0x00400000)
#define DMA_FLAG_DMEIF3_7 ((uint32_t)0x01000000)
#define DMA_FLAG_TEIF3_7 ((uint32_t)0x02000000)
#define DMA_FLAG_HTIF3_7 ((uint32_t)0x04000000)
#define DMA_FLAG_TCIF3_7 ((uint32_t)0x08000000)
/**
* @}
*/
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/** @brief Reset DMA handle state
* @param __HANDLE__: specifies the DMA handle.
* @retval None
*/
#define __HAL_DMA_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_DMA_STATE_RESET)
/**
* @brief Return the current DMA Stream FIFO filled level.
* @param __HANDLE__: DMA handle
* @retval The FIFO filling state.
* - DMA_FIFOStatus_Less1QuarterFull: when FIFO is less than 1 quarter-full
* and not empty.
* - DMA_FIFOStatus_1QuarterFull: if more than 1 quarter-full.
* - DMA_FIFOStatus_HalfFull: if more than 1 half-full.
* - DMA_FIFOStatus_3QuartersFull: if more than 3 quarters-full.
* - DMA_FIFOStatus_Empty: when FIFO is empty
* - DMA_FIFOStatus_Full: when FIFO is full
*/
#define __HAL_DMA_GET_FS(__HANDLE__) (((__HANDLE__)->Instance->FCR & (DMA_SxFCR_FS)))
/**
* @brief Enable the specified DMA Stream.
* @param __HANDLE__: DMA handle
* @retval None
*/
#define __HAL_DMA_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR |= DMA_SxCR_EN)
/**
* @brief Disable the specified DMA Stream.
* @param __HANDLE__: DMA handle
* @retval None
*/
#define __HAL_DMA_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR &= ~DMA_SxCR_EN)
/* Interrupt & Flag management */
/**
* @brief Return the current DMA Stream transfer complete flag.
* @param __HANDLE__: DMA handle
* @retval The specified transfer complete flag index.
*/
#define __HAL_DMA_GET_TC_FLAG_INDEX(__HANDLE__) \
(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream0))? DMA_FLAG_TCIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream0))? DMA_FLAG_TCIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream4))? DMA_FLAG_TCIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream4))? DMA_FLAG_TCIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream1))? DMA_FLAG_TCIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream1))? DMA_FLAG_TCIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream5))? DMA_FLAG_TCIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream5))? DMA_FLAG_TCIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream2))? DMA_FLAG_TCIF2_6 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream2))? DMA_FLAG_TCIF2_6 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream6))? DMA_FLAG_TCIF2_6 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream6))? DMA_FLAG_TCIF2_6 :\
DMA_FLAG_TCIF3_7)
/**
* @brief Return the current DMA Stream half transfer complete flag.
* @param __HANDLE__: DMA handle
* @retval The specified half transfer complete flag index.
*/
#define __HAL_DMA_GET_HT_FLAG_INDEX(__HANDLE__)\
(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream0))? DMA_FLAG_HTIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream0))? DMA_FLAG_HTIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream4))? DMA_FLAG_HTIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream4))? DMA_FLAG_HTIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream1))? DMA_FLAG_HTIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream1))? DMA_FLAG_HTIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream5))? DMA_FLAG_HTIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream5))? DMA_FLAG_HTIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream2))? DMA_FLAG_HTIF2_6 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream2))? DMA_FLAG_HTIF2_6 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream6))? DMA_FLAG_HTIF2_6 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream6))? DMA_FLAG_HTIF2_6 :\
DMA_FLAG_HTIF3_7)
/**
* @brief Return the current DMA Stream transfer error flag.
* @param __HANDLE__: DMA handle
* @retval The specified transfer error flag index.
*/
#define __HAL_DMA_GET_TE_FLAG_INDEX(__HANDLE__)\
(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream0))? DMA_FLAG_TEIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream0))? DMA_FLAG_TEIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream4))? DMA_FLAG_TEIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream4))? DMA_FLAG_TEIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream1))? DMA_FLAG_TEIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream1))? DMA_FLAG_TEIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream5))? DMA_FLAG_TEIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream5))? DMA_FLAG_TEIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream2))? DMA_FLAG_TEIF2_6 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream2))? DMA_FLAG_TEIF2_6 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream6))? DMA_FLAG_TEIF2_6 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream6))? DMA_FLAG_TEIF2_6 :\
DMA_FLAG_TEIF3_7)
/**
* @brief Return the current DMA Stream FIFO error flag.
* @param __HANDLE__: DMA handle
* @retval The specified FIFO error flag index.
*/
#define __HAL_DMA_GET_FE_FLAG_INDEX(__HANDLE__)\
(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream0))? DMA_FLAG_FEIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream0))? DMA_FLAG_FEIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream4))? DMA_FLAG_FEIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream4))? DMA_FLAG_FEIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream1))? DMA_FLAG_FEIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream1))? DMA_FLAG_FEIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream5))? DMA_FLAG_FEIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream5))? DMA_FLAG_FEIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream2))? DMA_FLAG_FEIF2_6 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream2))? DMA_FLAG_FEIF2_6 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream6))? DMA_FLAG_FEIF2_6 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream6))? DMA_FLAG_FEIF2_6 :\
DMA_FLAG_FEIF3_7)
/**
* @brief Return the current DMA Stream direct mode error flag.
* @param __HANDLE__: DMA handle
* @retval The specified direct mode error flag index.
*/
#define __HAL_DMA_GET_DME_FLAG_INDEX(__HANDLE__)\
(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream0))? DMA_FLAG_DMEIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream0))? DMA_FLAG_DMEIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream4))? DMA_FLAG_DMEIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream4))? DMA_FLAG_DMEIF0_4 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream1))? DMA_FLAG_DMEIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream1))? DMA_FLAG_DMEIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream5))? DMA_FLAG_DMEIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream5))? DMA_FLAG_DMEIF1_5 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream2))? DMA_FLAG_DMEIF2_6 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream2))? DMA_FLAG_DMEIF2_6 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Stream6))? DMA_FLAG_DMEIF2_6 :\
((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Stream6))? DMA_FLAG_DMEIF2_6 :\
DMA_FLAG_DMEIF3_7)
/**
* @brief Get the DMA Stream pending flags.
* @param __HANDLE__: DMA handle
* @param __FLAG__: Get the specified flag.
* This parameter can be any combination of the following values:
* @arg DMA_FLAG_TCIFx: Transfer complete flag.
* @arg DMA_FLAG_HTIFx: Half transfer complete flag.
* @arg DMA_FLAG_TEIFx: Transfer error flag.
* @arg DMA_FLAG_DMEIFx: Direct mode error flag.
* @arg DMA_FLAG_FEIFx: FIFO error flag.
* Where x can be 0_4, 1_5, 2_6 or 3_7 to select the DMA Stream flag.
* @retval The state of FLAG (SET or RESET).
*/
#define __HAL_DMA_GET_FLAG(__HANDLE__, __FLAG__)\
(((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA2_Stream3)? (DMA2->HISR & (__FLAG__)) :\
((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA1_Stream7)? (DMA2->LISR & (__FLAG__)) :\
((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA1_Stream3)? (DMA1->HISR & (__FLAG__)) : (DMA1->LISR & (__FLAG__)))
/**
* @brief Clear the DMA Stream pending flags.
* @param __HANDLE__: DMA handle
* @param __FLAG__: specifies the flag to clear.
* This parameter can be any combination of the following values:
* @arg DMA_FLAG_TCIFx: Transfer complete flag.
* @arg DMA_FLAG_HTIFx: Half transfer complete flag.
* @arg DMA_FLAG_TEIFx: Transfer error flag.
* @arg DMA_FLAG_DMEIFx: Direct mode error flag.
* @arg DMA_FLAG_FEIFx: FIFO error flag.
* Where x can be 0_4, 1_5, 2_6 or 3_7 to select the DMA Stream flag.
* @retval None
*/
#define __HAL_DMA_CLEAR_FLAG(__HANDLE__, __FLAG__) \
(((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA2_Stream3)? (DMA2->HIFCR = (__FLAG__)) :\
((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA1_Stream7)? (DMA2->LIFCR = (__FLAG__)) :\
((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA1_Stream3)? (DMA1->HIFCR = (__FLAG__)) : (DMA1->LIFCR = (__FLAG__)))
/**
* @brief Enable the specified DMA Stream interrupts.
* @param __HANDLE__: DMA handle
* @param __INTERRUPT__: specifies the DMA interrupt sources to be enabled or disabled.
* This parameter can be any combination of the following values:
* @arg DMA_IT_TC: Transfer complete interrupt mask.
* @arg DMA_IT_HT: Half transfer complete interrupt mask.
* @arg DMA_IT_TE: Transfer error interrupt mask.
* @arg DMA_IT_FE: FIFO error interrupt mask.
* @arg DMA_IT_DME: Direct mode error interrupt.
* @retval None
*/
#define __HAL_DMA_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((__INTERRUPT__) != DMA_IT_FE)? \
((__HANDLE__)->Instance->CR |= (__INTERRUPT__)) : ((__HANDLE__)->Instance->FCR |= (__INTERRUPT__)))
/**
* @brief Disable the specified DMA Stream interrupts.
* @param __HANDLE__: DMA handle
* @param __INTERRUPT__: specifies the DMA interrupt sources to be enabled or disabled.
* This parameter can be any combination of the following values:
* @arg DMA_IT_TC: Transfer complete interrupt mask.
* @arg DMA_IT_HT: Half transfer complete interrupt mask.
* @arg DMA_IT_TE: Transfer error interrupt mask.
* @arg DMA_IT_FE: FIFO error interrupt mask.
* @arg DMA_IT_DME: Direct mode error interrupt.
* @retval None
*/
#define __HAL_DMA_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((__INTERRUPT__) != DMA_IT_FE)? \
((__HANDLE__)->Instance->CR &= ~(__INTERRUPT__)) : ((__HANDLE__)->Instance->FCR &= ~(__INTERRUPT__)))
/**
* @brief Check whether the specified DMA Stream interrupt is enabled or disabled.
* @param __HANDLE__: DMA handle
* @param __INTERRUPT__: specifies the DMA interrupt source to check.
* This parameter can be one of the following values:
* @arg DMA_IT_TC: Transfer complete interrupt mask.
* @arg DMA_IT_HT: Half transfer complete interrupt mask.
* @arg DMA_IT_TE: Transfer error interrupt mask.
* @arg DMA_IT_FE: FIFO error interrupt mask.
* @arg DMA_IT_DME: Direct mode error interrupt.
* @retval The state of DMA_IT.
*/
#define __HAL_DMA_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) (((__INTERRUPT__) != DMA_IT_FE)? \
((__HANDLE__)->Instance->CR & (__INTERRUPT__)) : \
((__HANDLE__)->Instance->FCR & (__INTERRUPT__)))
/**
* @brief Writes the number of data units to be transferred on the DMA Stream.
* @param __HANDLE__: DMA handle
* @param __COUNTER__: Number of data units to be transferred (from 0 to 65535)
* Number of data items depends only on the Peripheral data format.
*
* @note If Peripheral data format is Bytes: number of data units is equal
* to total number of bytes to be transferred.
*
* @note If Peripheral data format is Half-Word: number of data units is
* equal to total number of bytes to be transferred / 2.
*
* @note If Peripheral data format is Word: number of data units is equal
* to total number of bytes to be transferred / 4.
*
* @retval The number of remaining data units in the current DMAy Streamx transfer.
*/
#define __HAL_DMA_SET_COUNTER(__HANDLE__, __COUNTER__) ((__HANDLE__)->Instance->NDTR = (uint16_t)(__COUNTER__))
/**
* @brief Returns the number of remaining data units in the current DMAy Streamx transfer.
* @param __HANDLE__: DMA handle
*
* @retval The number of remaining data units in the current DMA Stream transfer.
*/
#define __HAL_DMA_GET_COUNTER(__HANDLE__) ((__HANDLE__)->Instance->NDTR)
/* Include DMA HAL Extension module */
//#include "mbed-stm32f4xx_hal_dma_ex.h"
/* Exported functions --------------------------------------------------------*/
/** @defgroup DMA_Exported_Functions DMA Exported Functions
* @brief DMA Exported functions
* @{
*/
/** @defgroup DMA_Exported_Functions_Group1 Initialization and de-initialization functions
* @brief Initialization and de-initialization functions
* @{
*/
HAL_StatusTypeDef HAL_DMA_Init(DMA_HandleTypeDef *hdma);
HAL_StatusTypeDef HAL_DMA_DeInit(DMA_HandleTypeDef *hdma);
/**
* @}
*/
/** @defgroup DMA_Exported_Functions_Group2 I/O operation functions
* @brief I/O operation functions
* @{
*/
HAL_StatusTypeDef HAL_DMA_Start (DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength);
HAL_StatusTypeDef HAL_DMA_Start_IT(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength);
HAL_StatusTypeDef HAL_DMA_Abort(DMA_HandleTypeDef *hdma);
HAL_StatusTypeDef HAL_DMA_PollForTransfer(DMA_HandleTypeDef *hdma, uint32_t CompleteLevel, uint32_t Timeout);
void HAL_DMA_IRQHandler(DMA_HandleTypeDef *hdma);
/**
* @}
*/
/** @defgroup DMA_Exported_Functions_Group3 Peripheral State functions
* @brief Peripheral State functions
* @{
*/
HAL_DMA_StateTypeDef HAL_DMA_GetState(DMA_HandleTypeDef *hdma);
uint32_t HAL_DMA_GetError(DMA_HandleTypeDef *hdma);
/**
* @}
*/
/**
* @}
*/
/* Private Constants -------------------------------------------------------------*/
/** @defgroup DMA_Private_Constants DMA Private Constants
* @brief DMA private defines and constants
* @{
*/
/**
* @}
*/
/* Private macros ------------------------------------------------------------*/
/** @defgroup DMA_Private_Macros DMA Private Macros
* @brief DMA private macros
* @{
*/
#define IS_DMA_CHANNEL(CHANNEL) (((CHANNEL) == DMA_CHANNEL_0) || \
((CHANNEL) == DMA_CHANNEL_1) || \
((CHANNEL) == DMA_CHANNEL_2) || \
((CHANNEL) == DMA_CHANNEL_3) || \
((CHANNEL) == DMA_CHANNEL_4) || \
((CHANNEL) == DMA_CHANNEL_5) || \
((CHANNEL) == DMA_CHANNEL_6) || \
((CHANNEL) == DMA_CHANNEL_7))
#define IS_DMA_DIRECTION(DIRECTION) (((DIRECTION) == DMA_PERIPH_TO_MEMORY ) || \
((DIRECTION) == DMA_MEMORY_TO_PERIPH) || \
((DIRECTION) == DMA_MEMORY_TO_MEMORY))
#define IS_DMA_BUFFER_SIZE(SIZE) (((SIZE) >= 0x1) && ((SIZE) < 0x10000))
#define IS_DMA_PERIPHERAL_INC_STATE(STATE) (((STATE) == DMA_PINC_ENABLE) || \
((STATE) == DMA_PINC_DISABLE))
#define IS_DMA_MEMORY_INC_STATE(STATE) (((STATE) == DMA_MINC_ENABLE) || \
((STATE) == DMA_MINC_DISABLE))
#define IS_DMA_PERIPHERAL_DATA_SIZE(SIZE) (((SIZE) == DMA_PDATAALIGN_BYTE) || \
((SIZE) == DMA_PDATAALIGN_HALFWORD) || \
((SIZE) == DMA_PDATAALIGN_WORD))
#define IS_DMA_MEMORY_DATA_SIZE(SIZE) (((SIZE) == DMA_MDATAALIGN_BYTE) || \
((SIZE) == DMA_MDATAALIGN_HALFWORD) || \
((SIZE) == DMA_MDATAALIGN_WORD ))
#define IS_DMA_MODE(MODE) (((MODE) == DMA_NORMAL ) || \
((MODE) == DMA_CIRCULAR) || \
((MODE) == DMA_PFCTRL))
#define IS_DMA_PRIORITY(PRIORITY) (((PRIORITY) == DMA_PRIORITY_LOW ) || \
((PRIORITY) == DMA_PRIORITY_MEDIUM) || \
((PRIORITY) == DMA_PRIORITY_HIGH) || \
((PRIORITY) == DMA_PRIORITY_VERY_HIGH))
#define IS_DMA_FIFO_MODE_STATE(STATE) (((STATE) == DMA_FIFOMODE_DISABLE ) || \
((STATE) == DMA_FIFOMODE_ENABLE))
#define IS_DMA_FIFO_THRESHOLD(THRESHOLD) (((THRESHOLD) == DMA_FIFO_THRESHOLD_1QUARTERFULL ) || \
((THRESHOLD) == DMA_FIFO_THRESHOLD_HALFFULL) || \
((THRESHOLD) == DMA_FIFO_THRESHOLD_3QUARTERSFULL) || \
((THRESHOLD) == DMA_FIFO_THRESHOLD_FULL))
#define IS_DMA_MEMORY_BURST(BURST) (((BURST) == DMA_MBURST_SINGLE) || \
((BURST) == DMA_MBURST_INC4) || \
((BURST) == DMA_MBURST_INC8) || \
((BURST) == DMA_MBURST_INC16))
#define IS_DMA_PERIPHERAL_BURST(BURST) (((BURST) == DMA_PBURST_SINGLE) || \
((BURST) == DMA_PBURST_INC4) || \
((BURST) == DMA_PBURST_INC8) || \
((BURST) == DMA_PBURST_INC16))
/**
* @}
*/
/* Private functions ---------------------------------------------------------*/
/** @defgroup DMA_Private_Functions DMA Private Functions
* @brief DMA private functions
* @{
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* __STM32F4xx_HAL_DMA_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

442
mbed-stm32f4xx_hal_flash.h
View File

@ -1,442 +0,0 @@
/**
******************************************************************************
* @file stm32f4xx_hal_flash.h
* @author MCD Application Team
* @version V1.3.2
* @date 26-June-2015
* @brief Header file of FLASH HAL module.
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F4xx_HAL_FLASH_H
#define __STM32F4xx_HAL_FLASH_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "mbed-stm32f4xx_hal_def.h"
/** @addtogroup STM32F4xx_HAL_Driver
* @{
*/
/** @addtogroup FLASH
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup FLASH_Exported_Types FLASH Exported Types
* @{
*/
/**
* @brief FLASH Procedure structure definition
*/
typedef enum
{
FLASH_PROC_NONE = 0,
FLASH_PROC_SECTERASE,
FLASH_PROC_MASSERASE,
FLASH_PROC_PROGRAM
} FLASH_ProcedureTypeDef;
/**
* @brief FLASH handle Structure definition
*/
typedef struct
{
__IO FLASH_ProcedureTypeDef ProcedureOnGoing; /*Internal variable to indicate which procedure is ongoing or not in IT context*/
__IO uint32_t NbSectorsToErase; /*Internal variable to save the remaining sectors to erase in IT context*/
__IO uint8_t VoltageForErase; /*Internal variable to provide voltage range selected by user in IT context*/
__IO uint32_t Sector; /*Internal variable to define the current sector which is erasing*/
__IO uint32_t Bank; /*Internal variable to save current bank selected during mass erase*/
__IO uint32_t Address; /*Internal variable to save address selected for program*/
HAL_LockTypeDef Lock; /* FLASH locking object */
__IO uint32_t ErrorCode; /* FLASH error code */
}FLASH_ProcessTypeDef;
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup FLASH_Exported_Constants FLASH Exported Constants
* @{
*/
/** @defgroup FLASH_Error_Code FLASH Error Code
* @brief FLASH Error Code
* @{
*/
#define HAL_FLASH_ERROR_NONE ((uint32_t)0x00000000) /*!< No error */
#define HAL_FLASH_ERROR_RD ((uint32_t)0x00000001) /*!< Read Protection error */
#define HAL_FLASH_ERROR_PGS ((uint32_t)0x00000002) /*!< Programming Sequence error */
#define HAL_FLASH_ERROR_PGP ((uint32_t)0x00000004) /*!< Programming Parallelism error */
#define HAL_FLASH_ERROR_PGA ((uint32_t)0x00000008) /*!< Programming Alignment error */
#define HAL_FLASH_ERROR_WRP ((uint32_t)0x00000010) /*!< Write protection error */
#define HAL_FLASH_ERROR_OPERATION ((uint32_t)0x00000020) /*!< Operation Error */
/**
* @}
*/
/** @defgroup FLASH_Type_Program FLASH Type Program
* @{
*/
#define FLASH_TYPEPROGRAM_BYTE ((uint32_t)0x00) /*!< Program byte (8-bit) at a specified address */
#define FLASH_TYPEPROGRAM_HALFWORD ((uint32_t)0x01) /*!< Program a half-word (16-bit) at a specified address */
#define FLASH_TYPEPROGRAM_WORD ((uint32_t)0x02) /*!< Program a word (32-bit) at a specified address */
#define FLASH_TYPEPROGRAM_DOUBLEWORD ((uint32_t)0x03) /*!< Program a double word (64-bit) at a specified address */
/**
* @}
*/
/** @defgroup FLASH_Flag_definition FLASH Flag definition
* @brief Flag definition
* @{
*/
#define FLASH_FLAG_EOP FLASH_SR_EOP /*!< FLASH End of Operation flag */
#define FLASH_FLAG_OPERR FLASH_SR_SOP /*!< FLASH operation Error flag */
#define FLASH_FLAG_WRPERR FLASH_SR_WRPERR /*!< FLASH Write protected error flag */
#define FLASH_FLAG_PGAERR FLASH_SR_PGAERR /*!< FLASH Programming Alignment error flag */
#define FLASH_FLAG_PGPERR FLASH_SR_PGPERR /*!< FLASH Programming Parallelism error flag */
#define FLASH_FLAG_PGSERR FLASH_SR_PGSERR /*!< FLASH Programming Sequence error flag */
#define FLASH_FLAG_RDERR ((uint32_t)0x00000100) /*!< Read Protection error flag (PCROP) */
#define FLASH_FLAG_BSY FLASH_SR_BSY /*!< FLASH Busy flag */
/**
* @}
*/
/** @defgroup FLASH_Interrupt_definition FLASH Interrupt definition
* @brief FLASH Interrupt definition
* @{
*/
#define FLASH_IT_EOP FLASH_CR_EOPIE /*!< End of FLASH Operation Interrupt source */
#define FLASH_IT_ERR ((uint32_t)0x02000000) /*!< Error Interrupt source */
/**
* @}
*/
/** @defgroup FLASH_Program_Parallelism FLASH Program Parallelism
* @{
*/
#define FLASH_PSIZE_BYTE ((uint32_t)0x00000000)
#define FLASH_PSIZE_HALF_WORD ((uint32_t)0x00000100)
#define FLASH_PSIZE_WORD ((uint32_t)0x00000200)
#define FLASH_PSIZE_DOUBLE_WORD ((uint32_t)0x00000300)
#define CR_PSIZE_MASK ((uint32_t)0xFFFFFCFF)
/**
* @}
*/
/** @defgroup FLASH_Keys FLASH Keys
* @{
*/
#define RDP_KEY ((uint16_t)0x00A5)
#define FLASH_KEY1 ((uint32_t)0x45670123)
#define FLASH_KEY2 ((uint32_t)0xCDEF89AB)
#define FLASH_OPT_KEY1 ((uint32_t)0x08192A3B)
#define FLASH_OPT_KEY2 ((uint32_t)0x4C5D6E7F)
/**
* @}
*/
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/** @defgroup FLASH_Exported_Macros FLASH Exported Macros
* @{
*/
/**
* @brief Set the FLASH Latency.
* @param __LATENCY__: FLASH Latency
* The value of this parameter depend on device used within the same series
* @retval none
*/
#define __HAL_FLASH_SET_LATENCY(__LATENCY__) (*(__IO uint8_t *)ACR_BYTE0_ADDRESS = (uint8_t)(__LATENCY__))
/**
* @brief Get the FLASH Latency.
* @retval FLASH Latency
* The value of this parameter depend on device used within the same series
*/
#define __HAL_FLASH_GET_LATENCY() (READ_BIT((FLASH->ACR), FLASH_ACR_LATENCY))
/**
* @brief Enable the FLASH prefetch buffer.
* @retval none
*/
#define __HAL_FLASH_PREFETCH_BUFFER_ENABLE() (FLASH->ACR |= FLASH_ACR_PRFTEN)
/**
* @brief Disable the FLASH prefetch buffer.
* @retval none
*/
#define __HAL_FLASH_PREFETCH_BUFFER_DISABLE() (FLASH->ACR &= (~FLASH_ACR_PRFTEN))
/**
* @brief Enable the FLASH instruction cache.
* @retval none
*/
#define __HAL_FLASH_INSTRUCTION_CACHE_ENABLE() (FLASH->ACR |= FLASH_ACR_ICEN)
/**
* @brief Disable the FLASH instruction cache.
* @retval none
*/
#define __HAL_FLASH_INSTRUCTION_CACHE_DISABLE() (FLASH->ACR &= (~FLASH_ACR_ICEN))
/**
* @brief Enable the FLASH data cache.
* @retval none
*/
#define __HAL_FLASH_DATA_CACHE_ENABLE() (FLASH->ACR |= FLASH_ACR_DCEN)
/**
* @brief Disable the FLASH data cache.
* @retval none
*/
#define __HAL_FLASH_DATA_CACHE_DISABLE() (FLASH->ACR &= (~FLASH_ACR_DCEN))
/**
* @brief Resets the FLASH instruction Cache.
* @note This function must be used only when the Instruction Cache is disabled.
* @retval None
*/
#define __HAL_FLASH_INSTRUCTION_CACHE_RESET() do {FLASH->ACR |= FLASH_ACR_ICRST; \
FLASH->ACR &= ~FLASH_ACR_ICRST; \
}while(0)
/**
* @brief Resets the FLASH data Cache.
* @note This function must be used only when the data Cache is disabled.
* @retval None
*/
#define __HAL_FLASH_DATA_CACHE_RESET() do {FLASH->ACR |= FLASH_ACR_DCRST; \
FLASH->ACR &= ~FLASH_ACR_DCRST; \
}while(0)
/**
* @brief Enable the specified FLASH interrupt.
* @param __INTERRUPT__ : FLASH interrupt
* This parameter can be any combination of the following values:
* @arg FLASH_IT_EOP: End of FLASH Operation Interrupt
* @arg FLASH_IT_ERR: Error Interrupt
* @retval none
*/
#define __HAL_FLASH_ENABLE_IT(__INTERRUPT__) (FLASH->CR |= (__INTERRUPT__))
/**
* @brief Disable the specified FLASH interrupt.
* @param __INTERRUPT__ : FLASH interrupt
* This parameter can be any combination of the following values:
* @arg FLASH_IT_EOP: End of FLASH Operation Interrupt
* @arg FLASH_IT_ERR: Error Interrupt
* @retval none
*/
#define __HAL_FLASH_DISABLE_IT(__INTERRUPT__) (FLASH->CR &= ~(uint32_t)(__INTERRUPT__))
/**
* @brief Get the specified FLASH flag status.
* @param __FLAG__: specifies the FLASH flag to check.
* This parameter can be one of the following values:
* @arg FLASH_FLAG_EOP : FLASH End of Operation flag
* @arg FLASH_FLAG_OPERR : FLASH operation Error flag
* @arg FLASH_FLAG_WRPERR: FLASH Write protected error flag
* @arg FLASH_FLAG_PGAERR: FLASH Programming Alignment error flag
* @arg FLASH_FLAG_PGPERR: FLASH Programming Parallelism error flag
* @arg FLASH_FLAG_PGSERR: FLASH Programming Sequence error flag
* @arg FLASH_FLAG_RDERR : FLASH Read Protection error flag (PCROP)
* @arg FLASH_FLAG_BSY : FLASH Busy flag
* @retval The new state of __FLAG__ (SET or RESET).
*/
#define __HAL_FLASH_GET_FLAG(__FLAG__) ((FLASH->SR & (__FLAG__)))
/**
* @brief Clear the specified FLASH flag.
* @param __FLAG__: specifies the FLASH flags to clear.
* This parameter can be any combination of the following values:
* @arg FLASH_FLAG_EOP : FLASH End of Operation flag
* @arg FLASH_FLAG_OPERR : FLASH operation Error flag
* @arg FLASH_FLAG_WRPERR: FLASH Write protected error flag
* @arg FLASH_FLAG_PGAERR: FLASH Programming Alignment error flag
* @arg FLASH_FLAG_PGPERR: FLASH Programming Parallelism error flag
* @arg FLASH_FLAG_PGSERR: FLASH Programming Sequence error flag
* @arg FLASH_FLAG_RDERR : FLASH Read Protection error flag (PCROP)
* @retval none
*/
#define __HAL_FLASH_CLEAR_FLAG(__FLAG__) (FLASH->SR = (__FLAG__))
/**
* @}
*/
/* Include FLASH HAL Extension module */
//#include "mbed-stm32f4xx_hal_flash_ex.h"
//#include "mbed-stm32f4xx_hal_flash_ramfunc.h"
/* Exported functions --------------------------------------------------------*/
/** @addtogroup FLASH_Exported_Functions
* @{
*/
/** @addtogroup FLASH_Exported_Functions_Group1
* @{
*/
/* Program operation functions ***********************************************/
HAL_StatusTypeDef HAL_FLASH_Program(uint32_t TypeProgram, uint32_t Address, uint64_t Data);
HAL_StatusTypeDef HAL_FLASH_Program_IT(uint32_t TypeProgram, uint32_t Address, uint64_t Data);
/* FLASH IRQ handler method */
void HAL_FLASH_IRQHandler(void);
/* Callbacks in non blocking modes */
void HAL_FLASH_EndOfOperationCallback(uint32_t ReturnValue);
void HAL_FLASH_OperationErrorCallback(uint32_t ReturnValue);
/**
* @}
*/
/** @addtogroup FLASH_Exported_Functions_Group2
* @{
*/
/* Peripheral Control functions **********************************************/
HAL_StatusTypeDef HAL_FLASH_Unlock(void);
HAL_StatusTypeDef HAL_FLASH_Lock(void);
HAL_StatusTypeDef HAL_FLASH_OB_Unlock(void);
HAL_StatusTypeDef HAL_FLASH_OB_Lock(void);
/* Option bytes control */
HAL_StatusTypeDef HAL_FLASH_OB_Launch(void);
/**
* @}
*/
/** @addtogroup FLASH_Exported_Functions_Group3
* @{
*/
/* Peripheral State functions ************************************************/
uint32_t HAL_FLASH_GetError(void);
HAL_StatusTypeDef FLASH_WaitForLastOperation(uint32_t Timeout);
/**
* @}
*/
/**
* @}
*/
/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/** @defgroup FLASH_Private_Variables FLASH Private Variables
* @{
*/
/**
* @}
*/
/* Private constants ---------------------------------------------------------*/
/** @defgroup FLASH_Private_Constants FLASH Private Constants
* @{
*/
/**
* @brief ACR register byte 0 (Bits[7:0]) base address
*/
#define ACR_BYTE0_ADDRESS ((uint32_t)0x40023C00)
/**
* @brief OPTCR register byte 0 (Bits[7:0]) base address
*/
#define OPTCR_BYTE0_ADDRESS ((uint32_t)0x40023C14)
/**
* @brief OPTCR register byte 1 (Bits[15:8]) base address
*/
#define OPTCR_BYTE1_ADDRESS ((uint32_t)0x40023C15)
/**
* @brief OPTCR register byte 2 (Bits[23:16]) base address
*/
#define OPTCR_BYTE2_ADDRESS ((uint32_t)0x40023C16)
/**
* @brief OPTCR register byte 3 (Bits[31:24]) base address
*/
#define OPTCR_BYTE3_ADDRESS ((uint32_t)0x40023C17)
/**
* @}
*/
/* Private macros ------------------------------------------------------------*/
/** @defgroup FLASH_Private_Macros FLASH Private Macros
* @{
*/
/** @defgroup FLASH_IS_FLASH_Definitions FLASH Private macros to check input parameters
* @{
*/
#define IS_FLASH_TYPEPROGRAM(VALUE)(((VALUE) == FLASH_TYPEPROGRAM_BYTE) || \
((VALUE) == FLASH_TYPEPROGRAM_HALFWORD) || \
((VALUE) == FLASH_TYPEPROGRAM_WORD) || \
((VALUE) == FLASH_TYPEPROGRAM_DOUBLEWORD))
/**
* @}
*/
/**
* @}
*/
/* Private functions ---------------------------------------------------------*/
/** @defgroup FLASH_Private_Functions FLASH Private Functions
* @{
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* __STM32F4xx_HAL_FLASH_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

545
mbed-stm32f4xx_hal_gpio.c
View File

@ -1,545 +0,0 @@
/**
******************************************************************************
* @file stm32f4xx_hal_gpio.c
* @author MCD Application Team
* @version V1.3.2
* @date 26-June-2015
* @brief GPIO HAL module driver.
* This file provides firmware functions to manage the following
* functionalities of the General Purpose Input/Output (GPIO) peripheral:
* + Initialization and de-initialization functions
* + IO operation functions
*
@verbatim
==============================================================================
##### GPIO Peripheral features #####
==============================================================================
[..]
Subject to the specific hardware characteristics of each I/O port listed in the datasheet, each
port bit of the General Purpose IO (GPIO) Ports, can be individually configured by software
in several modes:
(+) Input mode
(+) Analog mode
(+) Output mode
(+) Alternate function mode
(+) External interrupt/event lines
[..]
During and just after reset, the alternate functions and external interrupt
lines are not active and the I/O ports are configured in input floating mode.
[..]
All GPIO pins have weak internal pull-up and pull-down resistors, which can be
activated or not.
[..]
In Output or Alternate mode, each IO can be configured on open-drain or push-pull
type and the IO speed can be selected depending on the VDD value.
[..]
All ports have external interrupt/event capability. To use external interrupt
lines, the port must be configured in input mode. All available GPIO pins are
connected to the 16 external interrupt/event lines from EXTI0 to EXTI15.
[..]
The external interrupt/event controller consists of up to 23 edge detectors
(16 lines are connected to GPIO) for generating event/interrupt requests (each
input line can be independently configured to select the type (interrupt or event)
and the corresponding trigger event (rising or falling or both). Each line can
also be masked independently.
##### How to use this driver #####
==============================================================================
[..]
(#) Enable the GPIO AHB clock using the following function: __HAL_RCC_GPIOx_CLK_ENABLE().
(#) Configure the GPIO pin(s) using HAL_GPIO_Init().
(++) Configure the IO mode using "Mode" member from GPIO_InitTypeDef structure
(++) Activate Pull-up, Pull-down resistor using "Pull" member from GPIO_InitTypeDef
structure.
(++) In case of Output or alternate function mode selection: the speed is
configured through "Speed" member from GPIO_InitTypeDef structure.
(++) In alternate mode is selection, the alternate function connected to the IO
is configured through "Alternate" member from GPIO_InitTypeDef structure.
(++) Analog mode is required when a pin is to be used as ADC channel
or DAC output.
(++) In case of external interrupt/event selection the "Mode" member from
GPIO_InitTypeDef structure select the type (interrupt or event) and
the corresponding trigger event (rising or falling or both).
(#) In case of external interrupt/event mode selection, configure NVIC IRQ priority
mapped to the EXTI line using HAL_NVIC_SetPriority() and enable it using
HAL_NVIC_EnableIRQ().
(#) To get the level of a pin configured in input mode use HAL_GPIO_ReadPin().
(#) To set/reset the level of a pin configured in output mode use
HAL_GPIO_WritePin()/HAL_GPIO_TogglePin().
(#) To lock pin configuration until next reset use HAL_GPIO_LockPin().
(#) During and just after reset, the alternate functions are not
active and the GPIO pins are configured in input floating mode (except JTAG
pins).
(#) The LSE oscillator pins OSC32_IN and OSC32_OUT can be used as general purpose
(PC14 and PC15, respectively) when the LSE oscillator is off. The LSE has
priority over the GPIO function.
(#) The HSE oscillator pins OSC_IN/OSC_OUT can be used as
general purpose PH0 and PH1, respectively, when the HSE oscillator is off.
The HSE has priority over the GPIO function.
@endverbatim
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "mbed-stm32f4xx_hal.h"
/** @addtogroup STM32F4xx_HAL_Driver
* @{
*/
/** @defgroup GPIO GPIO
* @brief GPIO HAL module driver
* @{
*/
#ifdef HAL_GPIO_MODULE_ENABLED
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/** @addtogroup GPIO_Private_Constants GPIO Private Constants
* @{
*/
#define GPIO_MODE ((uint32_t)0x00000003)
#define EXTI_MODE ((uint32_t)0x10000000)
#define GPIO_MODE_IT ((uint32_t)0x00010000)
#define GPIO_MODE_EVT ((uint32_t)0x00020000)
#define RISING_EDGE ((uint32_t)0x00100000)
#define FALLING_EDGE ((uint32_t)0x00200000)
#define GPIO_OUTPUT_TYPE ((uint32_t)0x00000010)
#define GPIO_NUMBER ((uint32_t)16)
/**
* @}
*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
/* Exported functions --------------------------------------------------------*/
/** @defgroup GPIO_Exported_Functions GPIO Exported Functions
* @{
*/
/** @defgroup GPIO_Exported_Functions_Group1 Initialization and de-initialization functions
* @brief Initialization and Configuration functions
*
@verbatim
===============================================================================
##### Initialization and de-initialization functions #####
===============================================================================
[..]
This section provides functions allowing to initialize and de-initialize the GPIOs
to be ready for use.
@endverbatim
* @{
*/
/**
* @brief Initializes the GPIOx peripheral according to the specified parameters in the GPIO_Init.
* @param GPIOx: where x can be (A..K) to select the GPIO peripheral for STM32F429X device or
* x can be (A..I) to select the GPIO peripheral for STM32F40XX and STM32F427X devices.
* @param GPIO_Init: pointer to a GPIO_InitTypeDef structure that contains
* the configuration information for the specified GPIO peripheral.
* @retval None
*/
void HAL_GPIO_Init(GPIO_TypeDef *GPIOx, GPIO_InitTypeDef *GPIO_Init)
{
uint32_t position;
uint32_t ioposition = 0x00;
uint32_t iocurrent = 0x00;
uint32_t temp = 0x00;
/* Check the parameters */
assert_param(IS_GPIO_ALL_INSTANCE(GPIOx));
assert_param(IS_GPIO_PIN(GPIO_Init->Pin));
assert_param(IS_GPIO_MODE(GPIO_Init->Mode));
assert_param(IS_GPIO_PULL(GPIO_Init->Pull));
/* Configure the port pins */
for(position = 0; position < GPIO_NUMBER; position++)
{
/* Get the IO position */
ioposition = ((uint32_t)0x01) << position;
/* Get the current IO position */
iocurrent = (uint32_t)(GPIO_Init->Pin) & ioposition;
if(iocurrent == ioposition)
{
/*--------------------- GPIO Mode Configuration ------------------------*/
/* In case of Alternate function mode selection */
if((GPIO_Init->Mode == GPIO_MODE_AF_PP) || (GPIO_Init->Mode == GPIO_MODE_AF_OD))
{
/* Check the Alternate function parameter */
assert_param(IS_GPIO_AF(GPIO_Init->Alternate));
/* Configure Alternate function mapped with the current IO */
temp = GPIOx->AFR[position >> 3];
temp &= ~((uint32_t)0xF << ((uint32_t)(position & (uint32_t)0x07) * 4)) ;
temp |= ((uint32_t)(GPIO_Init->Alternate) << (((uint32_t)position & (uint32_t)0x07) * 4));
GPIOx->AFR[position >> 3] = temp;
}
/* Configure IO Direction mode (Input, Output, Alternate or Analog) */
temp = GPIOx->MODER;
temp &= ~(GPIO_MODER_MODER0 << (position * 2));
temp |= ((GPIO_Init->Mode & GPIO_MODE) << (position * 2));
GPIOx->MODER = temp;
/* In case of Output or Alternate function mode selection */
if((GPIO_Init->Mode == GPIO_MODE_OUTPUT_PP) || (GPIO_Init->Mode == GPIO_MODE_AF_PP) ||
(GPIO_Init->Mode == GPIO_MODE_OUTPUT_OD) || (GPIO_Init->Mode == GPIO_MODE_AF_OD))
{
/* Check the Speed parameter */
assert_param(IS_GPIO_SPEED(GPIO_Init->Speed));
/* Configure the IO Speed */
temp = GPIOx->OSPEEDR;
temp &= ~(GPIO_OSPEEDER_OSPEEDR0 << (position * 2));
temp |= (GPIO_Init->Speed << (position * 2));
GPIOx->OSPEEDR = temp;
/* Configure the IO Output Type */
temp = GPIOx->OTYPER;
temp &= ~(GPIO_OTYPER_OT_0 << position) ;
temp |= (((GPIO_Init->Mode & GPIO_OUTPUT_TYPE) >> 4) << position);
GPIOx->OTYPER = temp;
}
/* Activate the Pull-up or Pull down resistor for the current IO */
temp = GPIOx->PUPDR;
temp &= ~(GPIO_PUPDR_PUPDR0 << (position * 2));
temp |= ((GPIO_Init->Pull) << (position * 2));
GPIOx->PUPDR = temp;
/*--------------------- EXTI Mode Configuration ------------------------*/
/* Configure the External Interrupt or event for the current IO */
if((GPIO_Init->Mode & EXTI_MODE) == EXTI_MODE)
{
/* Enable SYSCFG Clock */
__HAL_RCC_SYSCFG_CLK_ENABLE();
temp = SYSCFG->EXTICR[position >> 2];
temp &= ~(((uint32_t)0x0F) << (4 * (position & 0x03)));
temp |= ((uint32_t)(GPIO_GET_INDEX(GPIOx)) << (4 * (position & 0x03)));
SYSCFG->EXTICR[position >> 2] = temp;
/* Clear EXTI line configuration */
temp = EXTI->IMR;
temp &= ~((uint32_t)iocurrent);
if((GPIO_Init->Mode & GPIO_MODE_IT) == GPIO_MODE_IT)
{
temp |= iocurrent;
}
EXTI->IMR = temp;
temp = EXTI->EMR;
temp &= ~((uint32_t)iocurrent);
if((GPIO_Init->Mode & GPIO_MODE_EVT) == GPIO_MODE_EVT)
{
temp |= iocurrent;
}
EXTI->EMR = temp;
/* Clear Rising Falling edge configuration */
temp = EXTI->RTSR;
temp &= ~((uint32_t)iocurrent);
if((GPIO_Init->Mode & RISING_EDGE) == RISING_EDGE)
{
temp |= iocurrent;
}
EXTI->RTSR = temp;
temp = EXTI->FTSR;
temp &= ~((uint32_t)iocurrent);
if((GPIO_Init->Mode & FALLING_EDGE) == FALLING_EDGE)
{
temp |= iocurrent;
}
EXTI->FTSR = temp;
}
}
}
}
/**
* @brief De-initializes the GPIOx peripheral registers to their default reset values.
* @param GPIOx: where x can be (A..K) to select the GPIO peripheral for STM32F429X device or
* x can be (A..I) to select the GPIO peripheral for STM32F40XX and STM32F427X devices.
* @param GPIO_Pin: specifies the port bit to be written.
* This parameter can be one of GPIO_PIN_x where x can be (0..15).
* @retval None
*/
void HAL_GPIO_DeInit(GPIO_TypeDef *GPIOx, uint32_t GPIO_Pin)
{
uint32_t position;
uint32_t ioposition = 0x00;
uint32_t iocurrent = 0x00;
uint32_t tmp = 0x00;
/* Check the parameters */
assert_param(IS_GPIO_ALL_INSTANCE(GPIOx));
/* Configure the port pins */
for(position = 0; position < GPIO_NUMBER; position++)
{
/* Get the IO position */
ioposition = ((uint32_t)0x01) << position;
/* Get the current IO position */
iocurrent = (GPIO_Pin) & ioposition;
if(iocurrent == ioposition)
{
/*------------------------- GPIO Mode Configuration --------------------*/
/* Configure IO Direction in Input Floating Mode */
GPIOx->MODER &= ~(GPIO_MODER_MODER0 << (position * 2));
/* Configure the default Alternate Function in current IO */
GPIOx->AFR[position >> 3] &= ~((uint32_t)0xF << ((uint32_t)(position & (uint32_t)0x07) * 4)) ;
/* Configure the default value for IO Speed */
GPIOx->OSPEEDR &= ~(GPIO_OSPEEDER_OSPEEDR0 << (position * 2));
/* Configure the default value IO Output Type */
GPIOx->OTYPER &= ~(GPIO_OTYPER_OT_0 << position) ;
/* Deactivate the Pull-up and Pull-down resistor for the current IO */
GPIOx->PUPDR &= ~(GPIO_PUPDR_PUPDR0 << (position * 2));
/*------------------------- EXTI Mode Configuration --------------------*/
tmp = SYSCFG->EXTICR[position >> 2];
tmp &= (((uint32_t)0x0F) << (4 * (position & 0x03)));
if(tmp == ((uint32_t)(GPIO_GET_INDEX(GPIOx)) << (4 * (position & 0x03))))
{
/* Configure the External Interrupt or event for the current IO */
tmp = ((uint32_t)0x0F) << (4 * (position & 0x03));
SYSCFG->EXTICR[position >> 2] &= ~tmp;
/* Clear EXTI line configuration */
EXTI->IMR &= ~((uint32_t)iocurrent);
EXTI->EMR &= ~((uint32_t)iocurrent);
/* Clear Rising Falling edge configuration */
EXTI->RTSR &= ~((uint32_t)iocurrent);
EXTI->FTSR &= ~((uint32_t)iocurrent);
}
}
}
}
/**
* @}
*/
/** @defgroup GPIO_Exported_Functions_Group2 IO operation functions
* @brief GPIO Read and Write
*
@verbatim
===============================================================================
##### IO operation functions #####
===============================================================================
@endverbatim
* @{
*/
/**
* @brief Reads the specified input port pin.
* @param GPIOx: where x can be (A..K) to select the GPIO peripheral for STM32F429X device or
* x can be (A..I) to select the GPIO peripheral for STM32F40XX and STM32F427X devices.
* @param GPIO_Pin: specifies the port bit to read.
* This parameter can be GPIO_PIN_x where x can be (0..15).
* @retval The input port pin value.
*/
GPIO_PinState HAL_GPIO_ReadPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
{
GPIO_PinState bitstatus;
/* Check the parameters */
assert_param(IS_GPIO_PIN(GPIO_Pin));
if((GPIOx->IDR & GPIO_Pin) != (uint32_t)GPIO_PIN_RESET)
{
bitstatus = GPIO_PIN_SET;
}
else
{
bitstatus = GPIO_PIN_RESET;
}
return bitstatus;
}
/**
* @brief Sets or clears the selected data port bit.
*
* @note This function uses GPIOx_BSRR register to allow atomic read/modify
* accesses. In this way, there is no risk of an IRQ occurring between
* the read and the modify access.
*
* @param GPIOx: where x can be (A..K) to select the GPIO peripheral for STM32F429X device or
* x can be (A..I) to select the GPIO peripheral for STM32F40XX and STM32F427X devices.
* @param GPIO_Pin: specifies the port bit to be written.
* This parameter can be one of GPIO_PIN_x where x can be (0..15).
* @param PinState: specifies the value to be written to the selected bit.
* This parameter can be one of the GPIO_PinState enum values:
* @arg GPIO_PIN_RESET: to clear the port pin
* @arg GPIO_PIN_SET: to set the port pin
* @retval None
*/
void HAL_GPIO_WritePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState)
{
/* Check the parameters */
assert_param(IS_GPIO_PIN(GPIO_Pin));
assert_param(IS_GPIO_PIN_ACTION(PinState));
if(PinState != GPIO_PIN_RESET)
{
GPIOx->BSRR = GPIO_Pin;
}
else
{
GPIOx->BSRR = (uint32_t)GPIO_Pin << 16;
}
}
/**
* @brief Toggles the specified GPIO pins.
* @param GPIOx: Where x can be (A..K) to select the GPIO peripheral for STM32F429X device or
* x can be (A..I) to select the GPIO peripheral for STM32F40XX and STM32F427X devices.
* @param GPIO_Pin: Specifies the pins to be toggled.
* @retval None
*/
void HAL_GPIO_TogglePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
{
/* Check the parameters */
assert_param(IS_GPIO_PIN(GPIO_Pin));
GPIOx->ODR ^= GPIO_Pin;
}
/**
* @brief Locks GPIO Pins configuration registers.
* @note The locked registers are GPIOx_MODER, GPIOx_OTYPER, GPIOx_OSPEEDR,
* GPIOx_PUPDR, GPIOx_AFRL and GPIOx_AFRH.
* @note The configuration of the locked GPIO pins can no longer be modified
* until the next reset.
* @param GPIOx: where x can be (A..F) to select the GPIO peripheral for STM32F4 family
* @param GPIO_Pin: specifies the port bit to be locked.
* This parameter can be any combination of GPIO_PIN_x where x can be (0..15).
* @retval None
*/
HAL_StatusTypeDef HAL_GPIO_LockPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
{
__IO uint32_t tmp = GPIO_LCKR_LCKK;
/* Check the parameters */
assert_param(IS_GPIO_PIN(GPIO_Pin));
/* Apply lock key write sequence */
tmp |= GPIO_Pin;
/* Set LCKx bit(s): LCKK='1' + LCK[15-0] */
GPIOx->LCKR = tmp;
/* Reset LCKx bit(s): LCKK='0' + LCK[15-0] */
GPIOx->LCKR = GPIO_Pin;
/* Set LCKx bit(s): LCKK='1' + LCK[15-0] */
GPIOx->LCKR = tmp;
/* Read LCKK bit*/
tmp = GPIOx->LCKR;
if((GPIOx->LCKR & GPIO_LCKR_LCKK) != RESET)
{
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @brief This function handles EXTI interrupt request.
* @param GPIO_Pin: Specifies the pins connected EXTI line
* @retval None
*/
void HAL_GPIO_EXTI_IRQHandler(uint16_t GPIO_Pin)
{
/* EXTI line interrupt detected */
if(__HAL_GPIO_EXTI_GET_IT(GPIO_Pin) != RESET)
{
__HAL_GPIO_EXTI_CLEAR_IT(GPIO_Pin);
HAL_GPIO_EXTI_Callback(GPIO_Pin);
}
}
/**
* @brief EXTI line detection callbacks.
* @param GPIO_Pin: Specifies the pins connected EXTI line
* @retval None
*/
__weak void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin)
{
/* NOTE: This function Should not be modified, when the callback is needed,
the HAL_GPIO_EXTI_Callback could be implemented in the user file
*/
}
/**
* @}
*/
/**
* @}
*/
#endif /* HAL_GPIO_MODULE_ENABLED */
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

335
mbed-stm32f4xx_hal_gpio.h
View File

@ -1,335 +0,0 @@
/**
******************************************************************************
* @file stm32f4xx_hal_gpio.h
* @author MCD Application Team
* @version V1.3.2
* @date 26-June-2015
* @brief Header file of GPIO HAL module.
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F4xx_HAL_GPIO_H
#define __STM32F4xx_HAL_GPIO_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "mbed-stm32f4xx_hal_def.h"
/** @addtogroup STM32F4xx_HAL_Driver
* @{
*/
/** @addtogroup GPIO
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup GPIO_Exported_Types GPIO Exported Types
* @{
*/
/**
* @brief GPIO Init structure definition
*/
typedef struct
{
uint32_t Pin; /*!< Specifies the GPIO pins to be configured.
This parameter can be any value of @ref GPIO_pins_define */
uint32_t Mode; /*!< Specifies the operating mode for the selected pins.
This parameter can be a value of @ref GPIO_mode_define */
uint32_t Pull; /*!< Specifies the Pull-up or Pull-Down activation for the selected pins.
This parameter can be a value of @ref GPIO_pull_define */
uint32_t Speed; /*!< Specifies the speed for the selected pins.
This parameter can be a value of @ref GPIO_speed_define */
uint32_t Alternate; /*!< Peripheral to be connected to the selected pins.
This parameter can be a value of @ref GPIO_Alternate_function_selection */
}GPIO_InitTypeDef;
/**
* @brief GPIO Bit SET and Bit RESET enumeration
*/
typedef enum
{
GPIO_PIN_RESET = 0,
GPIO_PIN_SET
}GPIO_PinState;
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup GPIO_Exported_Constants GPIO Exported Constants
* @{
*/
/** @defgroup GPIO_pins_define GPIO pins define
* @{
*/
#define GPIO_PIN_0 ((uint16_t)0x0001) /* Pin 0 selected */
#define GPIO_PIN_1 ((uint16_t)0x0002) /* Pin 1 selected */
#define GPIO_PIN_2 ((uint16_t)0x0004) /* Pin 2 selected */
#define GPIO_PIN_3 ((uint16_t)0x0008) /* Pin 3 selected */
#define GPIO_PIN_4 ((uint16_t)0x0010) /* Pin 4 selected */
#define GPIO_PIN_5 ((uint16_t)0x0020) /* Pin 5 selected */
#define GPIO_PIN_6 ((uint16_t)0x0040) /* Pin 6 selected */
#define GPIO_PIN_7 ((uint16_t)0x0080) /* Pin 7 selected */
#define GPIO_PIN_8 ((uint16_t)0x0100) /* Pin 8 selected */
#define GPIO_PIN_9 ((uint16_t)0x0200) /* Pin 9 selected */
#define GPIO_PIN_10 ((uint16_t)0x0400) /* Pin 10 selected */
#define GPIO_PIN_11 ((uint16_t)0x0800) /* Pin 11 selected */
#define GPIO_PIN_12 ((uint16_t)0x1000) /* Pin 12 selected */
#define GPIO_PIN_13 ((uint16_t)0x2000) /* Pin 13 selected */
#define GPIO_PIN_14 ((uint16_t)0x4000) /* Pin 14 selected */
#define GPIO_PIN_15 ((uint16_t)0x8000) /* Pin 15 selected */
#define GPIO_PIN_All ((uint16_t)0xFFFF) /* All pins selected */
#define GPIO_PIN_MASK ((uint32_t)0x0000FFFF) /* PIN mask for assert test */
/**
* @}
*/
/** @defgroup GPIO_mode_define GPIO mode define
* @brief GPIO Configuration Mode
* Elements values convention: 0xX0yz00YZ
* - X : GPIO mode or EXTI Mode
* - y : External IT or Event trigger detection
* - z : IO configuration on External IT or Event
* - Y : Output type (Push Pull or Open Drain)
* - Z : IO Direction mode (Input, Output, Alternate or Analog)
* @{
*/
#define GPIO_MODE_INPUT ((uint32_t)0x00000000) /*!< Input Floating Mode */
#define GPIO_MODE_OUTPUT_PP ((uint32_t)0x00000001) /*!< Output Push Pull Mode */
#define GPIO_MODE_OUTPUT_OD ((uint32_t)0x00000011) /*!< Output Open Drain Mode */
#define GPIO_MODE_AF_PP ((uint32_t)0x00000002) /*!< Alternate Function Push Pull Mode */
#define GPIO_MODE_AF_OD ((uint32_t)0x00000012) /*!< Alternate Function Open Drain Mode */
#define GPIO_MODE_ANALOG ((uint32_t)0x00000003) /*!< Analog Mode */
#define GPIO_MODE_IT_RISING ((uint32_t)0x10110000) /*!< External Interrupt Mode with Rising edge trigger detection */
#define GPIO_MODE_IT_FALLING ((uint32_t)0x10210000) /*!< External Interrupt Mode with Falling edge trigger detection */
#define GPIO_MODE_IT_RISING_FALLING ((uint32_t)0x10310000) /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
#define GPIO_MODE_EVT_RISING ((uint32_t)0x10120000) /*!< External Event Mode with Rising edge trigger detection */
#define GPIO_MODE_EVT_FALLING ((uint32_t)0x10220000) /*!< External Event Mode with Falling edge trigger detection */
#define GPIO_MODE_EVT_RISING_FALLING ((uint32_t)0x10320000) /*!< External Event Mode with Rising/Falling edge trigger detection */
/**
* @}
*/
/** @defgroup GPIO_speed_define GPIO speed define
* @brief GPIO Output Maximum frequency
* @{
*/
#define GPIO_SPEED_LOW ((uint32_t)0x00000000) /*!< Low speed */
#define GPIO_SPEED_MEDIUM ((uint32_t)0x00000001) /*!< Medium speed */
#define GPIO_SPEED_FAST ((uint32_t)0x00000002) /*!< Fast speed */
#define GPIO_SPEED_HIGH ((uint32_t)0x00000003) /*!< High speed */
/**
* @}
*/
/** @defgroup GPIO_pull_define GPIO pull define
* @brief GPIO Pull-Up or Pull-Down Activation
* @{
*/
#define GPIO_NOPULL ((uint32_t)0x00000000) /*!< No Pull-up or Pull-down activation */
#define GPIO_PULLUP ((uint32_t)0x00000001) /*!< Pull-up activation */
#define GPIO_PULLDOWN ((uint32_t)0x00000002) /*!< Pull-down activation */
/**
* @}
*/
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/** @defgroup GPIO_Exported_Macros GPIO Exported Macros
* @{
*/
/**
* @brief Checks whether the specified EXTI line flag is set or not.
* @param __EXTI_LINE__: specifies the EXTI line flag to check.
* This parameter can be GPIO_PIN_x where x can be(0..15)
* @retval The new state of __EXTI_LINE__ (SET or RESET).
*/
#define __HAL_GPIO_EXTI_GET_FLAG(__EXTI_LINE__) (EXTI->PR & (__EXTI_LINE__))
/**
* @brief Clears the EXTI's line pending flags.
* @param __EXTI_LINE__: specifies the EXTI lines flags to clear.
* This parameter can be any combination of GPIO_PIN_x where x can be (0..15)
* @retval None
*/
#define __HAL_GPIO_EXTI_CLEAR_FLAG(__EXTI_LINE__) (EXTI->PR = (__EXTI_LINE__))
/**
* @brief Checks whether the specified EXTI line is asserted or not.
* @param __EXTI_LINE__: specifies the EXTI line to check.
* This parameter can be GPIO_PIN_x where x can be(0..15)
* @retval The new state of __EXTI_LINE__ (SET or RESET).
*/
#define __HAL_GPIO_EXTI_GET_IT(__EXTI_LINE__) (EXTI->PR & (__EXTI_LINE__))
/**
* @brief Clears the EXTI's line pending bits.
* @param __EXTI_LINE__: specifies the EXTI lines to clear.
* This parameter can be any combination of GPIO_PIN_x where x can be (0..15)
* @retval None
*/
#define __HAL_GPIO_EXTI_CLEAR_IT(__EXTI_LINE__) (EXTI->PR = (__EXTI_LINE__))
/**
* @brief Generates a Software interrupt on selected EXTI line.
* @param __EXTI_LINE__: specifies the EXTI line to check.
* This parameter can be GPIO_PIN_x where x can be(0..15)
* @retval None
*/
#define __HAL_GPIO_EXTI_GENERATE_SWIT(__EXTI_LINE__) (EXTI->SWIER |= (__EXTI_LINE__))
/**
* @}
*/
#if defined (STM32F401xC) || defined (STM32F401xE) || defined (STM32F411xE)
#define GPIO_GET_INDEX(__GPIOx__) (uint8_t)(((__GPIOx__) == (GPIOA))? 0U :\
((__GPIOx__) == (GPIOB))? 1U :\
((__GPIOx__) == (GPIOC))? 2U :\
((__GPIOx__) == (GPIOD))? 3U :\
((__GPIOx__) == (GPIOE))? 4U : 5U)
#endif /* STM32F401xC || STM32F401xE || STM32F411xE */
/* Include GPIO HAL Extension module */
//#include "mbed-stm32f4xx_hal_gpio_ex.h"
/* Exported functions --------------------------------------------------------*/
/** @addtogroup GPIO_Exported_Functions
* @{
*/
/** @addtogroup GPIO_Exported_Functions_Group1
* @{
*/
/* Initialization and de-initialization functions *****************************/
void HAL_GPIO_Init(GPIO_TypeDef *GPIOx, GPIO_InitTypeDef *GPIO_Init);
void HAL_GPIO_DeInit(GPIO_TypeDef *GPIOx, uint32_t GPIO_Pin);
/**
* @}
*/
/** @addtogroup GPIO_Exported_Functions_Group2
* @{
*/
/* IO operation functions *****************************************************/
GPIO_PinState HAL_GPIO_ReadPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin);
void HAL_GPIO_WritePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState);
void HAL_GPIO_TogglePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin);
HAL_StatusTypeDef HAL_GPIO_LockPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin);
void HAL_GPIO_EXTI_IRQHandler(uint16_t GPIO_Pin);
void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin);
/**
* @}
*/
/**
* @}
*/
/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/
/** @defgroup GPIO_Private_Constants GPIO Private Constants
* @{
*/
/**
* @}
*/
/* Private macros ------------------------------------------------------------*/
/** @defgroup GPIO_Private_Macros GPIO Private Macros
* @{
*/
#define IS_GPIO_PIN_ACTION(ACTION) (((ACTION) == GPIO_PIN_RESET) || ((ACTION) == GPIO_PIN_SET))
#define IS_GPIO_PIN(PIN) (((PIN) & GPIO_PIN_MASK ) != (uint32_t)0x00)
#define IS_GPIO_MODE(MODE) (((MODE) == GPIO_MODE_INPUT) ||\
((MODE) == GPIO_MODE_OUTPUT_PP) ||\
((MODE) == GPIO_MODE_OUTPUT_OD) ||\
((MODE) == GPIO_MODE_AF_PP) ||\
((MODE) == GPIO_MODE_AF_OD) ||\
((MODE) == GPIO_MODE_IT_RISING) ||\
((MODE) == GPIO_MODE_IT_FALLING) ||\
((MODE) == GPIO_MODE_IT_RISING_FALLING) ||\
((MODE) == GPIO_MODE_EVT_RISING) ||\
((MODE) == GPIO_MODE_EVT_FALLING) ||\
((MODE) == GPIO_MODE_EVT_RISING_FALLING) ||\
((MODE) == GPIO_MODE_ANALOG))
#define IS_GPIO_SPEED(SPEED) (((SPEED) == GPIO_SPEED_LOW) || ((SPEED) == GPIO_SPEED_MEDIUM) || \
((SPEED) == GPIO_SPEED_FAST) || ((SPEED) == GPIO_SPEED_HIGH))
#define IS_GPIO_PULL(PULL) (((PULL) == GPIO_NOPULL) || ((PULL) == GPIO_PULLUP) || \
((PULL) == GPIO_PULLDOWN))
/**
* @}
*/
/* Private functions ---------------------------------------------------------*/
/** @defgroup GPIO_Private_Functions GPIO Private Functions
* @{
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* __STM32F4xx_HAL_GPIO_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

484
mbed-stm32f4xx_hal_pwr.h
View File

@ -1,484 +0,0 @@
/**
******************************************************************************
* @file stm32f4xx_hal_pwr.h
* @author MCD Application Team
* @version V1.3.2
* @date 26-June-2015
* @brief Header file of PWR HAL module.
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F4xx_HAL_PWR_H
#define __STM32F4xx_HAL_PWR_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "mbed-stm32f4xx_hal_def.h"
/** @addtogroup STM32F4xx_HAL_Driver
* @{
*/
/** @addtogroup PWR
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup PWR_Exported_Types PWR Exported Types
* @{
*/
/**
* @brief PWR PVD configuration structure definition
*/
typedef struct
{
uint32_t PVDLevel; /*!< PVDLevel: Specifies the PVD detection level.
This parameter can be a value of @ref PWR_PVD_detection_level */
uint32_t Mode; /*!< Mode: Specifies the operating mode for the selected pins.
This parameter can be a value of @ref PWR_PVD_Mode */
}PWR_PVDTypeDef;
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup PWR_Exported_Constants PWR Exported Constants
* @{
*/
/** @defgroup PWR_WakeUp_Pins PWR WakeUp Pins
* @{
*/
#define PWR_WAKEUP_PIN1 ((uint32_t)0x00000100)
#define PWR_WAKEUP_PIN2 ((uint32_t)0x00000080)
/**
* @}
*/
/** @defgroup PWR_PVD_detection_level PWR PVD detection level
* @{
*/
#define PWR_PVDLEVEL_0 PWR_CR_PLS_LEV0
#define PWR_PVDLEVEL_1 PWR_CR_PLS_LEV1
#define PWR_PVDLEVEL_2 PWR_CR_PLS_LEV2
#define PWR_PVDLEVEL_3 PWR_CR_PLS_LEV3
#define PWR_PVDLEVEL_4 PWR_CR_PLS_LEV4
#define PWR_PVDLEVEL_5 PWR_CR_PLS_LEV5
#define PWR_PVDLEVEL_6 PWR_CR_PLS_LEV6
#define PWR_PVDLEVEL_7 PWR_CR_PLS_LEV7/* External input analog voltage
(Compare internally to VREFINT) */
/**
* @}
*/
/** @defgroup PWR_PVD_Mode PWR PVD Mode
* @{
*/
#define PWR_PVD_MODE_NORMAL ((uint32_t)0x00000000) /*!< basic mode is used */
#define PWR_PVD_MODE_IT_RISING ((uint32_t)0x00010001) /*!< External Interrupt Mode with Rising edge trigger detection */
#define PWR_PVD_MODE_IT_FALLING ((uint32_t)0x00010002) /*!< External Interrupt Mode with Falling edge trigger detection */
#define PWR_PVD_MODE_IT_RISING_FALLING ((uint32_t)0x00010003) /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
#define PWR_PVD_MODE_EVENT_RISING ((uint32_t)0x00020001) /*!< Event Mode with Rising edge trigger detection */
#define PWR_PVD_MODE_EVENT_FALLING ((uint32_t)0x00020002) /*!< Event Mode with Falling edge trigger detection */
#define PWR_PVD_MODE_EVENT_RISING_FALLING ((uint32_t)0x00020003) /*!< Event Mode with Rising/Falling edge trigger detection */
/**
* @}
*/
/** @defgroup PWR_Regulator_state_in_STOP_mode PWR Regulator state in SLEEP/STOP mode
* @{
*/
#define PWR_MAINREGULATOR_ON ((uint32_t)0x00000000)
#define PWR_LOWPOWERREGULATOR_ON PWR_CR_LPDS
/**
* @}
*/
/** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry
* @{
*/
#define PWR_SLEEPENTRY_WFI ((uint8_t)0x01)
#define PWR_SLEEPENTRY_WFE ((uint8_t)0x02)
/**
* @}
*/
/** @defgroup PWR_STOP_mode_entry PWR STOP mode entry
* @{
*/
#define PWR_STOPENTRY_WFI ((uint8_t)0x01)
#define PWR_STOPENTRY_WFE ((uint8_t)0x02)
/**
* @}
*/
/** @defgroup PWR_Flag PWR Flag
* @{
*/
#define PWR_FLAG_WU PWR_CSR_WUF
#define PWR_FLAG_SB PWR_CSR_SBF
#define PWR_FLAG_PVDO PWR_CSR_PVDO
#define PWR_FLAG_BRR PWR_CSR_BRR
#define PWR_FLAG_VOSRDY PWR_CSR_VOSRDY
/**
* @}
*/
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/** @defgroup PWR_Exported_Macro PWR Exported Macro
* @{
*/
#if defined(STM32F405xx) || defined(STM32F407xx) || defined(STM32F415xx) || defined(STM32F417xx)
/** @brief macros configure the main internal regulator output voltage.
* @param __REGULATOR__: specifies the regulator output voltage to achieve
* a tradeoff between performance and power consumption when the device does
* not operate at the maximum frequency (refer to the datasheets for more details).
* This parameter can be one of the following values:
* @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode
* @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode
* @retval None
*/
#define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) do { \
__IO uint32_t tmpreg; \
MODIFY_REG(PWR->CR, PWR_CR_VOS, (__REGULATOR__)); \
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(PWR->CR, PWR_CR_VOS); \
UNUSED(tmpreg); \
} while(0)
#else
/** @brief macros configure the main internal regulator output voltage.
* @param __REGULATOR__: specifies the regulator output voltage to achieve
* a tradeoff between performance and power consumption when the device does
* not operate at the maximum frequency (refer to the datasheets for more details).
* This parameter can be one of the following values:
* @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode
* @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode
* @arg PWR_REGULATOR_VOLTAGE_SCALE3: Regulator voltage output Scale 3 mode
* @retval None
*/
#define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) do { \
__IO uint32_t tmpreg; \
MODIFY_REG(PWR->CR, PWR_CR_VOS, (__REGULATOR__)); \
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(PWR->CR, PWR_CR_VOS); \
UNUSED(tmpreg); \
} while(0)
#endif /* STM32F405xx || STM32F407xx || STM32F415xx || STM32F417xx */
/** @brief Check PWR flag is set or not.
* @param __FLAG__: specifies the flag to check.
* This parameter can be one of the following values:
* @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event
* was received from the WKUP pin or from the RTC alarm (Alarm A
* or Alarm B), RTC Tamper event, RTC TimeStamp event or RTC Wakeup.
* An additional wakeup event is detected if the WKUP pin is enabled
* (by setting the EWUP bit) when the WKUP pin level is already high.
* @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was
* resumed from StandBy mode.
* @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled
* by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode
* For this reason, this bit is equal to 0 after Standby or reset
* until the PVDE bit is set.
* @arg PWR_FLAG_BRR: Backup regulator ready flag. This bit is not reset
* when the device wakes up from Standby mode or by a system reset
* or power reset.
* @arg PWR_FLAG_VOSRDY: This flag indicates that the Regulator voltage
* scaling output selection is ready.
* @retval The new state of __FLAG__ (TRUE or FALSE).
*/
#define __HAL_PWR_GET_FLAG(__FLAG__) ((PWR->CSR & (__FLAG__)) == (__FLAG__))
/** @brief Clear the PWR's pending flags.
* @param __FLAG__: specifies the flag to clear.
* This parameter can be one of the following values:
* @arg PWR_FLAG_WU: Wake Up flag
* @arg PWR_FLAG_SB: StandBy flag
*/
#define __HAL_PWR_CLEAR_FLAG(__FLAG__) (PWR->CR |= (__FLAG__) << 2)
/**
* @brief Enable the PVD Exti Line 16.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_ENABLE_IT() (EXTI->IMR |= (PWR_EXTI_LINE_PVD))
/**
* @brief Disable the PVD EXTI Line 16.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_DISABLE_IT() (EXTI->IMR &= ~(PWR_EXTI_LINE_PVD))
/**
* @brief Enable event on PVD Exti Line 16.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_ENABLE_EVENT() (EXTI->EMR |= (PWR_EXTI_LINE_PVD))
/**
* @brief Disable event on PVD Exti Line 16.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_DISABLE_EVENT() (EXTI->EMR &= ~(PWR_EXTI_LINE_PVD))
/**
* @brief Enable the PVD Extended Interrupt Rising Trigger.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE() SET_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)
/**
* @brief Disable the PVD Extended Interrupt Rising Trigger.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE() CLEAR_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)
/**
* @brief Enable the PVD Extended Interrupt Falling Trigger.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE() SET_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)
/**
* @brief Disable the PVD Extended Interrupt Falling Trigger.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE() CLEAR_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)
/**
* @brief PVD EXTI line configuration: set rising & falling edge trigger.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_FALLING_EDGE() __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE();
/**
* @brief Disable the PVD Extended Interrupt Rising & Falling Trigger.
* This parameter can be:
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_FALLING_EDGE() __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE();
/**
* @brief checks whether the specified PVD Exti interrupt flag is set or not.
* @retval EXTI PVD Line Status.
*/
#define __HAL_PWR_PVD_EXTI_GET_FLAG() (EXTI->PR & (PWR_EXTI_LINE_PVD))
/**
* @brief Clear the PVD Exti flag.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_CLEAR_FLAG() (EXTI->PR = (PWR_EXTI_LINE_PVD))
/**
* @brief Generates a Software interrupt on PVD EXTI line.
* @retval None
*/
#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT() (EXTI->SWIER |= (PWR_EXTI_LINE_PVD))
/**
* @}
*/
/* Include PWR HAL Extension module */
//#include "mbed-stm32f4xx_hal_pwr_ex.h"
/* Exported functions --------------------------------------------------------*/
/** @addtogroup PWR_Exported_Functions PWR Exported Functions
* @{
*/
/** @addtogroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions
* @{
*/
/* Initialization and de-initialization functions *****************************/
void HAL_PWR_DeInit(void);
void HAL_PWR_EnableBkUpAccess(void);
void HAL_PWR_DisableBkUpAccess(void);
/**
* @}
*/
/** @addtogroup PWR_Exported_Functions_Group2 Peripheral Control functions
* @{
*/
/* Peripheral Control functions **********************************************/
/* PVD configuration */
void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD);
void HAL_PWR_EnablePVD(void);
void HAL_PWR_DisablePVD(void);
/* WakeUp pins configuration */
void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx);
void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx);
/* Low Power modes entry */
void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry);
void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry);
void HAL_PWR_EnterSTANDBYMode(void);
/* Power PVD IRQ Handler */
void HAL_PWR_PVD_IRQHandler(void);
void HAL_PWR_PVDCallback(void);
/* Cortex System Control functions *******************************************/
void HAL_PWR_EnableSleepOnExit(void);
void HAL_PWR_DisableSleepOnExit(void);
void HAL_PWR_EnableSEVOnPend(void);
void HAL_PWR_DisableSEVOnPend(void);
/**
* @}
*/
/**
* @}
*/
/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/
/** @defgroup PWR_Private_Constants PWR Private Constants
* @{
*/
/** @defgroup PWR_PVD_EXTI_Line PWR PVD EXTI Line
* @{
*/
#define PWR_EXTI_LINE_PVD ((uint32_t)EXTI_IMR_MR16) /*!< External interrupt line 16 Connected to the PVD EXTI Line */
/**
* @}
*/
/** @defgroup PWR_register_alias_address PWR Register alias address
* @{
*/
/* ------------- PWR registers bit address in the alias region ---------------*/
#define PWR_OFFSET (PWR_BASE - PERIPH_BASE)
#define PWR_CR_OFFSET 0x00
#define PWR_CSR_OFFSET 0x04
#define PWR_CR_OFFSET_BB (PWR_OFFSET + PWR_CR_OFFSET)
#define PWR_CSR_OFFSET_BB (PWR_OFFSET + PWR_CSR_OFFSET)
/**
* @}
*/
/** @defgroup PWR_CR_register_alias PWR CR Register alias address
* @{
*/
/* --- CR Register ---*/
/* Alias word address of DBP bit */
#define DBP_BIT_NUMBER POSITION_VAL(PWR_CR_DBP)
#define CR_DBP_BB (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (DBP_BIT_NUMBER * 4))
/* Alias word address of PVDE bit */
#define PVDE_BIT_NUMBER POSITION_VAL(PWR_CR_PVDE)
#define CR_PVDE_BB (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (PVDE_BIT_NUMBER * 4))
/* Alias word address of PMODE bit */
#define PMODE_BIT_NUMBER POSITION_VAL(PWR_CR_PMODE)
#define CR_PMODE_BB (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (PMODE_BIT_NUMBER * 4))
/**
* @}
*/
/** @defgroup PWR_CSR_register_alias PWR CSR Register alias address
* @{
*/
/* --- CSR Register ---*/
/* Alias word address of EWUP bit */
#define EWUP_BIT_NUMBER POSITION_VAL(PWR_CSR_EWUP)
#define CSR_EWUP_BB (PERIPH_BB_BASE + (PWR_CSR_OFFSET_BB * 32) + (EWUP_BIT_NUMBER * 4))
/**
* @}
*/
/**
* @}
*/
/* Private macros ------------------------------------------------------------*/
/** @defgroup PWR_Private_Macros PWR Private Macros
* @{
*/
/** @defgroup PWR_IS_PWR_Definitions PWR Private macros to check input parameters
* @{
*/
#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || ((PIN) == PWR_WAKEUP_PIN2))
#define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \
((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \
((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \
((LEVEL) == PWR_PVDLEVEL_6) || ((LEVEL) == PWR_PVDLEVEL_7))
#define IS_PWR_PVD_MODE(MODE) (((MODE) == PWR_PVD_MODE_IT_RISING)|| ((MODE) == PWR_PVD_MODE_IT_FALLING) || \
((MODE) == PWR_PVD_MODE_IT_RISING_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING) || \
((MODE) == PWR_PVD_MODE_EVENT_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING_FALLING) || \
((MODE) == PWR_PVD_MODE_NORMAL))
#define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \
((REGULATOR) == PWR_LOWPOWERREGULATOR_ON))
#define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || ((ENTRY) == PWR_SLEEPENTRY_WFE))
#define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || ((ENTRY) == PWR_STOPENTRY_WFE))
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* __STM32F4xx_HAL_PWR_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

82
mbed-stm32f4xx_hal_rcc.c
View File

@ -633,7 +633,8 @@ HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, ui
if(FLatency > (FLASH->ACR & FLASH_ACR_LATENCY))
{
/* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */
__HAL_FLASH_SET_LATENCY(FLatency);
FLASH->ACR &= 0xFFFFFFF0; // clear
FLASH->ACR |= FLatency;
/* Check that the new number of wait states is taken into account to access the Flash
memory by reading the FLASH_ACR register */
@ -819,7 +820,8 @@ HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, ui
}
/* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */
__HAL_FLASH_SET_LATENCY(FLatency);
FLASH->ACR &= 0xFFFFFFF0; // clear
FLASH->ACR |= FLatency;
/* Check that the new number of wait states is taken into account to access the Flash
memory by reading the FLASH_ACR register */
@ -894,50 +896,50 @@ HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, ui
* @arg RCC_MCODIV_5: division by 5 applied to MCOx clock
* @retval None
*/
void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv)
{
GPIO_InitTypeDef GPIO_InitStruct;
/* Check the parameters */
assert_param(IS_RCC_MCO(RCC_MCOx));
assert_param(IS_RCC_MCODIV(RCC_MCODiv));
/* RCC_MCO1 */
if(RCC_MCOx == RCC_MCO1)
{
assert_param(IS_RCC_MCO1SOURCE(RCC_MCOSource));
// void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv)
// {
// GPIO_InitTypeDef GPIO_InitStruct;
// /* Check the parameters */
// assert_param(IS_RCC_MCO(RCC_MCOx));
// assert_param(IS_RCC_MCODIV(RCC_MCODiv));
// /* RCC_MCO1 */
// if(RCC_MCOx == RCC_MCO1)
// {
// assert_param(IS_RCC_MCO1SOURCE(RCC_MCOSource));
/* MCO1 Clock Enable */
__MCO1_CLK_ENABLE();
// /* MCO1 Clock Enable */
// __MCO1_CLK_ENABLE();
/* Configure the MCO1 pin in alternate function mode */
GPIO_InitStruct.Pin = MCO1_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Alternate = (uint8_t)0x00; // GPIO_AF0_MCO
HAL_GPIO_Init(MCO1_GPIO_PORT, &GPIO_InitStruct);
// /* Configure the MCO1 pin in alternate function mode */
// GPIO_InitStruct.Pin = PIOA_8_PIN;
// GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
// GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
// GPIO_InitStruct.Pull = GPIO_NOPULL;
// GPIO_InitStruct.Alternate = (uint8_t)0x00; // GPIO_AF0_MCO
// HAL_GPIO_Init(MCO1_GPIO_PORT, &GPIO_InitStruct);
/* Mask MCO1 and MCO1PRE[2:0] bits then Select MCO1 clock source and prescaler */
MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO1 | RCC_CFGR_MCO1PRE), (RCC_MCOSource | RCC_MCODiv));
}
else
{
assert_param(IS_RCC_MCO2SOURCE(RCC_MCOSource));
// Mask MCO1 and MCO1PRE[2:0] bits then Select MCO1 clock source and prescaler
// MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO1 | RCC_CFGR_MCO1PRE), (RCC_MCOSource | RCC_MCODiv));
// }
// else
// {
// assert_param(IS_RCC_MCO2SOURCE(RCC_MCOSource));
/* MCO2 Clock Enable */
__MCO2_CLK_ENABLE();
// /* MCO2 Clock Enable */
// __MCO2_CLK_ENABLE();
/* Configure the MCO2 pin in alternate function mode */
GPIO_InitStruct.Pin = MCO2_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Alternate = (uint8_t)0x00; // GPIO_AF0_MCO
HAL_GPIO_Init(MCO2_GPIO_PORT, &GPIO_InitStruct);
// /* Configure the MCO2 pin in alternate function mode */
// GPIO_InitStruct.Pin = PIOC_0_PIN;
// GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
// GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
// GPIO_InitStruct.Pull = GPIO_NOPULL;
// GPIO_InitStruct.Alternate = (uint8_t)0x00; // GPIO_AF0_MCO
// HAL_GPIO_Init(MCO2_GPIO_PORT, &GPIO_InitStruct);
/* Mask MCO2 and MCO2PRE[2:0] bits then Select MCO2 clock source and prescaler */
MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO2 | RCC_CFGR_MCO2PRE), (RCC_MCOSource | (RCC_MCODiv << 3)));
}
}
// /* Mask MCO2 and MCO2PRE[2:0] bits then Select MCO2 clock source and prescaler */
// MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO2 | RCC_CFGR_MCO2PRE), (RCC_MCOSource | (RCC_MCODiv << 3)));
// }
// }
/**
* @brief Enables the Clock Security System.

722
mbed-stm32f4xx_hal_uart.h
View File

@ -1,722 +0,0 @@
/**
******************************************************************************
* @file stm32f4xx_hal_uart.h
* @author MCD Application Team
* @version V1.3.2
* @date 26-June-2015
* @brief Header file of UART HAL module.
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F4xx_HAL_UART_H
#define __STM32F4xx_HAL_UART_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "mbed-stm32f4xx_hal_def.h"
/** @addtogroup STM32F4xx_HAL_Driver
* @{
*/
/** @addtogroup UART
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup UART_Exported_Types UART Exported Types
* @{
*/
/**
* @brief UART Init Structure definition
*/
typedef struct
{
uint32_t BaudRate; /*!< This member configures the UART communication baud rate.
The baud rate is computed using the following formula:
- IntegerDivider = ((PCLKx) / (8 * (OVR8+1) * (huart->Init.BaudRate)))
- FractionalDivider = ((IntegerDivider - ((uint32_t) IntegerDivider)) * 8 * (OVR8+1)) + 0.5
Where OVR8 is the "oversampling by 8 mode" configuration bit in the CR1 register. */
uint32_t WordLength; /*!< Specifies the number of data bits transmitted or received in a frame.
This parameter can be a value of @ref UART_Word_Length */
uint32_t StopBits; /*!< Specifies the number of stop bits transmitted.
This parameter can be a value of @ref UART_Stop_Bits */
uint32_t Parity; /*!< Specifies the parity mode.
This parameter can be a value of @ref UART_Parity
@note When parity is enabled, the computed parity is inserted
at the MSB position of the transmitted data (9th bit when
the word length is set to 9 data bits; 8th bit when the
word length is set to 8 data bits). */
uint32_t Mode; /*!< Specifies whether the Receive or Transmit mode is enabled or disabled.
This parameter can be a value of @ref UART_Mode */
uint32_t HwFlowCtl; /*!< Specifies whether the hardware flow control mode is enabled
or disabled.
This parameter can be a value of @ref UART_Hardware_Flow_Control */
uint32_t OverSampling; /*!< Specifies whether the Over sampling 8 is enabled or disabled, to achieve higher speed (up to fPCLK/8).
This parameter can be a value of @ref UART_Over_Sampling */
}UART_InitTypeDef;
/**
* @brief HAL UART State structures definition
*/
typedef enum
{
HAL_UART_STATE_RESET = 0x00, /*!< Peripheral is not yet Initialized */
HAL_UART_STATE_READY = 0x01, /*!< Peripheral Initialized and ready for use */
HAL_UART_STATE_BUSY = 0x02, /*!< an internal process is ongoing */
HAL_UART_STATE_BUSY_TX = 0x12, /*!< Data Transmission process is ongoing */
HAL_UART_STATE_BUSY_RX = 0x22, /*!< Data Reception process is ongoing */
HAL_UART_STATE_BUSY_TX_RX = 0x32, /*!< Data Transmission and Reception process is ongoing */
HAL_UART_STATE_TIMEOUT = 0x03, /*!< Timeout state */
HAL_UART_STATE_ERROR = 0x04 /*!< Error */
}HAL_UART_StateTypeDef;
/**
* @brief UART handle Structure definition
*/
typedef struct
{
USART_TypeDef *Instance; /*!< UART registers base address */
UART_InitTypeDef Init; /*!< UART communication parameters */
uint8_t *pTxBuffPtr; /*!< Pointer to UART Tx transfer Buffer */
uint16_t TxXferSize; /*!< UART Tx Transfer size */
uint16_t TxXferCount; /*!< UART Tx Transfer Counter */
uint8_t *pRxBuffPtr; /*!< Pointer to UART Rx transfer Buffer */
uint16_t RxXferSize; /*!< UART Rx Transfer size */
uint16_t RxXferCount; /*!< UART Rx Transfer Counter */
DMA_HandleTypeDef *hdmatx; /*!< UART Tx DMA Handle parameters */
DMA_HandleTypeDef *hdmarx; /*!< UART Rx DMA Handle parameters */
HAL_LockTypeDef Lock; /*!< Locking object */
__IO HAL_UART_StateTypeDef State; /*!< UART communication state */
__IO uint32_t ErrorCode; /*!< UART Error code */
}UART_HandleTypeDef;
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup UART_Exported_Constants UART Exported constants
* @{
*/
/** @defgroup UART_Error_Code UART Error Code
* @brief UART Error Code
* @{
*/
#define HAL_UART_ERROR_NONE ((uint32_t)0x00000000) /*!< No error */
#define HAL_UART_ERROR_PE ((uint32_t)0x00000001) /*!< Parity error */
#define HAL_UART_ERROR_NE ((uint32_t)0x00000002) /*!< Noise error */
#define HAL_UART_ERROR_FE ((uint32_t)0x00000004) /*!< Frame error */
#define HAL_UART_ERROR_ORE ((uint32_t)0x00000008) /*!< Overrun error */
#define HAL_UART_ERROR_DMA ((uint32_t)0x00000010) /*!< DMA transfer error */
/**
* @}
*/
/** @defgroup UART_Word_Length UART Word Length
* @{
*/
#define UART_WORDLENGTH_8B ((uint32_t)0x00000000)
#define UART_WORDLENGTH_9B ((uint32_t)USART_CR1_M)
/**
* @}
*/
/** @defgroup UART_Stop_Bits UART Number of Stop Bits
* @{
*/
#define UART_STOPBITS_1 ((uint32_t)0x00000000)
#define UART_STOPBITS_2 ((uint32_t)USART_CR2_STOP_1)
/**
* @}
*/
/** @defgroup UART_Parity UART Parity
* @{
*/
#define UART_PARITY_NONE ((uint32_t)0x00000000)
#define UART_PARITY_EVEN ((uint32_t)USART_CR1_PCE)
#define UART_PARITY_ODD ((uint32_t)(USART_CR1_PCE | USART_CR1_PS))
/**
* @}
*/
/** @defgroup UART_Hardware_Flow_Control UART Hardware Flow Control
* @{
*/
#define UART_HWCONTROL_NONE ((uint32_t)0x00000000)
#define UART_HWCONTROL_RTS ((uint32_t)USART_CR3_RTSE)
#define UART_HWCONTROL_CTS ((uint32_t)USART_CR3_CTSE)
#define UART_HWCONTROL_RTS_CTS ((uint32_t)(USART_CR3_RTSE | USART_CR3_CTSE))
/**
* @}
*/
/** @defgroup UART_Mode UART Transfer Mode
* @{
*/
#define UART_MODE_RX ((uint32_t)USART_CR1_RE)
#define UART_MODE_TX ((uint32_t)USART_CR1_TE)
#define UART_MODE_TX_RX ((uint32_t)(USART_CR1_TE |USART_CR1_RE))
/**
* @}
*/
/** @defgroup UART_State UART State
* @{
*/
#define UART_STATE_DISABLE ((uint32_t)0x00000000)
#define UART_STATE_ENABLE ((uint32_t)USART_CR1_UE)
/**
* @}
*/
/** @defgroup UART_Over_Sampling UART Over Sampling
* @{
*/
#define UART_OVERSAMPLING_16 ((uint32_t)0x00000000)
#define UART_OVERSAMPLING_8 ((uint32_t)USART_CR1_OVER8)
/**
* @}
*/
/** @defgroup UART_LIN_Break_Detection_Length UART LIN Break Detection Length
* @{
*/
#define UART_LINBREAKDETECTLENGTH_10B ((uint32_t)0x00000000)
#define UART_LINBREAKDETECTLENGTH_11B ((uint32_t)0x00000020)
/**
* @}
*/
/** @defgroup UART_WakeUp_functions UART Wakeup Functions
* @{
*/
#define UART_WAKEUPMETHOD_IDLELINE ((uint32_t)0x00000000)
#define UART_WAKEUPMETHOD_ADDRESSMARK ((uint32_t)0x00000800)
/**
* @}
*/
/** @defgroup UART_Flags UART FLags
* Elements values convention: 0xXXXX
* - 0xXXXX : Flag mask in the SR register
* @{
*/
#define UART_FLAG_CTS ((uint32_t)USART_SR_CTS)
#define UART_FLAG_LBD ((uint32_t)USART_SR_LBD)
#define UART_FLAG_TXE ((uint32_t)USART_SR_TXE)
#define UART_FLAG_TC ((uint32_t)USART_SR_TC)
#define UART_FLAG_RXNE ((uint32_t)USART_SR_RXNE)
#define UART_FLAG_IDLE ((uint32_t)USART_SR_IDLE)
#define UART_FLAG_ORE ((uint32_t)USART_SR_ORE)
#define UART_FLAG_NE ((uint32_t)USART_SR_NE)
#define UART_FLAG_FE ((uint32_t)USART_SR_FE)
#define UART_FLAG_PE ((uint32_t)USART_SR_PE)
/**
* @}
*/
/** @defgroup UART_Interrupt_definition UART Interrupt Definitions
* Elements values convention: 0xY000XXXX
* - XXXX : Interrupt mask (16 bits) in the Y register
* - Y : Interrupt source register (2bits)
* - 0001: CR1 register
* - 0010: CR2 register
* - 0011: CR3 register
*
* @{
*/
#define UART_IT_PE ((uint32_t)(UART_CR1_REG_INDEX << 28 | USART_CR1_PEIE))
#define UART_IT_TXE ((uint32_t)(UART_CR1_REG_INDEX << 28 | USART_CR1_TXEIE))
#define UART_IT_TC ((uint32_t)(UART_CR1_REG_INDEX << 28 | USART_CR1_TCIE))
#define UART_IT_RXNE ((uint32_t)(UART_CR1_REG_INDEX << 28 | USART_CR1_RXNEIE))
#define UART_IT_IDLE ((uint32_t)(UART_CR1_REG_INDEX << 28 | USART_CR1_IDLEIE))
#define UART_IT_LBD ((uint32_t)(UART_CR2_REG_INDEX << 28 | USART_CR2_LBDIE))
#define UART_IT_CTS ((uint32_t)(UART_CR3_REG_INDEX << 28 | USART_CR3_CTSIE))
#define UART_IT_ERR ((uint32_t)(UART_CR3_REG_INDEX << 28 | USART_CR3_EIE))
/**
* @}
*/
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/** @defgroup UART_Exported_Macros UART Exported Macros
* @{
*/
/** @brief Reset UART handle state
* @param __HANDLE__: specifies the UART Handle.
* This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
* UART peripheral.
* @retval None
*/
#define __HAL_UART_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_UART_STATE_RESET)
/** @brief Flushes the UART DR register
* @param __HANDLE__: specifies the UART Handle.
*/
#define __HAL_UART_FLUSH_DRREGISTER(__HANDLE__) ((__HANDLE__)->Instance->DR)
/** @brief Checks whether the specified UART flag is set or not.
* @param __HANDLE__: specifies the UART Handle.
* This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
* UART peripheral.
* @param __FLAG__: specifies the flag to check.
* This parameter can be one of the following values:
* @arg UART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5)
* @arg UART_FLAG_LBD: LIN Break detection flag
* @arg UART_FLAG_TXE: Transmit data register empty flag
* @arg UART_FLAG_TC: Transmission Complete flag
* @arg UART_FLAG_RXNE: Receive data register not empty flag
* @arg UART_FLAG_IDLE: Idle Line detection flag
* @arg UART_FLAG_ORE: Overrun Error flag
* @arg UART_FLAG_NE: Noise Error flag
* @arg UART_FLAG_FE: Framing Error flag
* @arg UART_FLAG_PE: Parity Error flag
* @retval The new state of __FLAG__ (TRUE or FALSE).
*/
#define __HAL_UART_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR & (__FLAG__)) == (__FLAG__))
/** @brief Clears the specified UART pending flag.
* @param __HANDLE__: specifies the UART Handle.
* This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
* UART peripheral.
* @param __FLAG__: specifies the flag to check.
* This parameter can be any combination of the following values:
* @arg UART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5).
* @arg UART_FLAG_LBD: LIN Break detection flag.
* @arg UART_FLAG_TC: Transmission Complete flag.
* @arg UART_FLAG_RXNE: Receive data register not empty flag.
*
* @note PE (Parity error), FE (Framing error), NE (Noise error), ORE (Overrun
* error) and IDLE (Idle line detected) flags are cleared by software
* sequence: a read operation to USART_SR register followed by a read
* operation to USART_DR register.
* @note RXNE flag can be also cleared by a read to the USART_DR register.
* @note TC flag can be also cleared by software sequence: a read operation to
* USART_SR register followed by a write operation to USART_DR register.
* @note TXE flag is cleared only by a write to the USART_DR register.
*
* @retval None
*/
#define __HAL_UART_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->SR = ~(__FLAG__))
/** @brief Clear the UART PE pending flag.
* @param __HANDLE__: specifies the UART Handle.
* This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
* UART peripheral.
* @retval None
*/
#define __HAL_UART_CLEAR_PEFLAG(__HANDLE__) \
do{ \
__IO uint32_t tmpreg; \
tmpreg = (__HANDLE__)->Instance->SR; \
tmpreg = (__HANDLE__)->Instance->DR; \
UNUSED(tmpreg); \
} while(0)
/** @brief Clear the UART FE pending flag.
* @param __HANDLE__: specifies the UART Handle.
* This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
* UART peripheral.
* @retval None
*/
#define __HAL_UART_CLEAR_FEFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__)
/** @brief Clear the UART NE pending flag.
* @param __HANDLE__: specifies the UART Handle.
* This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
* UART peripheral.
* @retval None
*/
#define __HAL_UART_CLEAR_NEFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__)
/** @brief Clear the UART ORE pending flag.
* @param __HANDLE__: specifies the UART Handle.
* This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
* UART peripheral.
* @retval None
*/
#define __HAL_UART_CLEAR_OREFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__)
/** @brief Clear the UART IDLE pending flag.
* @param __HANDLE__: specifies the UART Handle.
* This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
* UART peripheral.
* @retval None
*/
#define __HAL_UART_CLEAR_IDLEFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__)
/** @brief Enable the specified UART interrupt.
* @param __HANDLE__: specifies the UART Handle.
* This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
* UART peripheral.
* @param __INTERRUPT__: specifies the UART interrupt source to enable.
* This parameter can be one of the following values:
* @arg UART_IT_CTS: CTS change interrupt
* @arg UART_IT_LBD: LIN Break detection interrupt
* @arg UART_IT_TXE: Transmit Data Register empty interrupt
* @arg UART_IT_TC: Transmission complete interrupt
* @arg UART_IT_RXNE: Receive Data register not empty interrupt
* @arg UART_IT_IDLE: Idle line detection interrupt
* @arg UART_IT_PE: Parity Error interrupt
* @arg UART_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
* @retval None
*/
#define UART_IT_MASK ((uint32_t)0x0000FFFF)
#define __HAL_UART_ENABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28) == 1)? ((__HANDLE__)->Instance->CR1 |= ((__INTERRUPT__) & UART_IT_MASK)): \
(((__INTERRUPT__) >> 28) == 2)? ((__HANDLE__)->Instance->CR2 |= ((__INTERRUPT__) & UART_IT_MASK)): \
((__HANDLE__)->Instance->CR3 |= ((__INTERRUPT__) & UART_IT_MASK)))
/** @brief Disable the specified UART interrupt.
* @param __HANDLE__: specifies the UART Handle.
* This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
* UART peripheral.
* @param __INTERRUPT__: specifies the UART interrupt source to disable.
* This parameter can be one of the following values:
* @arg UART_IT_CTS: CTS change interrupt
* @arg UART_IT_LBD: LIN Break detection interrupt
* @arg UART_IT_TXE: Transmit Data Register empty interrupt
* @arg UART_IT_TC: Transmission complete interrupt
* @arg UART_IT_RXNE: Receive Data register not empty interrupt
* @arg UART_IT_IDLE: Idle line detection interrupt
* @arg UART_IT_PE: Parity Error interrupt
* @arg UART_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
* @retval None
*/
#define __HAL_UART_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28) == 1)? ((__HANDLE__)->Instance->CR1 &= ~((__INTERRUPT__) & UART_IT_MASK)): \
(((__INTERRUPT__) >> 28) == 2)? ((__HANDLE__)->Instance->CR2 &= ~((__INTERRUPT__) & UART_IT_MASK)): \
((__HANDLE__)->Instance->CR3 &= ~ ((__INTERRUPT__) & UART_IT_MASK)))
/** @brief Checks whether the specified UART interrupt has occurred or not.
* @param __HANDLE__: specifies the UART Handle.
* This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
* UART peripheral.
* @param __IT__: specifies the UART interrupt source to check.
* This parameter can be one of the following values:
* @arg UART_IT_CTS: CTS change interrupt (not available for UART4 and UART5)
* @arg UART_IT_LBD: LIN Break detection interrupt
* @arg UART_IT_TXE: Transmit Data Register empty interrupt
* @arg UART_IT_TC: Transmission complete interrupt
* @arg UART_IT_RXNE: Receive Data register not empty interrupt
* @arg UART_IT_IDLE: Idle line detection interrupt
* @arg USART_IT_ERR: Error interrupt
* @retval The new state of __IT__ (TRUE or FALSE).
*/
#define __HAL_UART_GET_IT_SOURCE(__HANDLE__, __IT__) (((((__IT__) >> 28) == 1)? (__HANDLE__)->Instance->CR1:(((((uint32_t)(__IT__)) >> 28) == 2)? \
(__HANDLE__)->Instance->CR2 : (__HANDLE__)->Instance->CR3)) & (((uint32_t)(__IT__)) & UART_IT_MASK))
/** @brief Enable CTS flow control
* This macro allows to enable CTS hardware flow control for a given UART instance,
* without need to call HAL_UART_Init() function.
* As involving direct access to UART registers, usage of this macro should be fully endorsed by user.
* @note As macro is expected to be used for modifying CTS Hw flow control feature activation, without need
* for USART instance Deinit/Init, following conditions for macro call should be fulfilled :
* - UART instance should have already been initialised (through call of HAL_UART_Init() )
* - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__))
* and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)).
* @param __HANDLE__: specifies the UART Handle.
* The Handle Instance can be USART1, USART2 or LPUART.
* @retval None
*/
#define __HAL_UART_HWCONTROL_CTS_ENABLE(__HANDLE__) \
do{ \
SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \
(__HANDLE__)->Init.HwFlowCtl |= USART_CR3_CTSE; \
} while(0)
/** @brief Disable CTS flow control
* This macro allows to disable CTS hardware flow control for a given UART instance,
* without need to call HAL_UART_Init() function.
* As involving direct access to UART registers, usage of this macro should be fully endorsed by user.
* @note As macro is expected to be used for modifying CTS Hw flow control feature activation, without need
* for USART instance Deinit/Init, following conditions for macro call should be fulfilled :
* - UART instance should have already been initialised (through call of HAL_UART_Init() )
* - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__))
* and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)).
* @param __HANDLE__: specifies the UART Handle.
* The Handle Instance can be USART1, USART2 or LPUART.
* @retval None
*/
#define __HAL_UART_HWCONTROL_CTS_DISABLE(__HANDLE__) \
do{ \
CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \
(__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_CTSE); \
} while(0)
/** @brief Enable RTS flow control
* This macro allows to enable RTS hardware flow control for a given UART instance,
* without need to call HAL_UART_Init() function.
* As involving direct access to UART registers, usage of this macro should be fully endorsed by user.
* @note As macro is expected to be used for modifying RTS Hw flow control feature activation, without need
* for USART instance Deinit/Init, following conditions for macro call should be fulfilled :
* - UART instance should have already been initialised (through call of HAL_UART_Init() )
* - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__))
* and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)).
* @param __HANDLE__: specifies the UART Handle.
* The Handle Instance can be USART1, USART2 or LPUART.
* @retval None
*/
#define __HAL_UART_HWCONTROL_RTS_ENABLE(__HANDLE__) \
do{ \
SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE); \
(__HANDLE__)->Init.HwFlowCtl |= USART_CR3_RTSE; \
} while(0)
/** @brief Disable RTS flow control
* This macro allows to disable RTS hardware flow control for a given UART instance,
* without need to call HAL_UART_Init() function.
* As involving direct access to UART registers, usage of this macro should be fully endorsed by user.
* @note As macro is expected to be used for modifying RTS Hw flow control feature activation, without need
* for USART instance Deinit/Init, following conditions for macro call should be fulfilled :
* - UART instance should have already been initialised (through call of HAL_UART_Init() )
* - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__))
* and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)).
* @param __HANDLE__: specifies the UART Handle.
* The Handle Instance can be USART1, USART2 or LPUART.
* @retval None
*/
#define __HAL_UART_HWCONTROL_RTS_DISABLE(__HANDLE__) \
do{ \
CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE);\
(__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_RTSE); \
} while(0)
/** @brief macros to enables the UART's one bit sample method
* @param __HANDLE__: specifies the UART Handle.
* @retval None
*/
#define __HAL_UART_ONE_BIT_SAMPLE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3|= USART_CR3_ONEBIT)
/** @brief macros to disables the UART's one bit sample method
* @param __HANDLE__: specifies the UART Handle.
* @retval None
*/
#define __HAL_UART_ONE_BIT_SAMPLE_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 &= (uint16_t)~((uint16_t)USART_CR3_ONEBIT))
/** @brief Enable UART
* @param __HANDLE__: specifies the UART Handle.
* @retval None
*/
#define __HAL_UART_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 |= USART_CR1_UE)
/** @brief Disable UART
* @param __HANDLE__: specifies the UART Handle.
* @retval None
*/
#define __HAL_UART_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE)
/**
* @}
*/
/* Exported functions --------------------------------------------------------*/
/** @addtogroup UART_Exported_Functions
* @{
*/
/** @addtogroup UART_Exported_Functions_Group1
* @{
*/
/* Initialization/de-initialization functions **********************************/
HAL_StatusTypeDef HAL_UART_Init(UART_HandleTypeDef *huart);
HAL_StatusTypeDef HAL_HalfDuplex_Init(UART_HandleTypeDef *huart);
HAL_StatusTypeDef HAL_LIN_Init(UART_HandleTypeDef *huart, uint32_t BreakDetectLength);
HAL_StatusTypeDef HAL_MultiProcessor_Init(UART_HandleTypeDef *huart, uint8_t Address, uint32_t WakeUpMethod);
HAL_StatusTypeDef HAL_UART_DeInit (UART_HandleTypeDef *huart);
void HAL_UART_MspInit(UART_HandleTypeDef *huart);
void HAL_UART_MspDeInit(UART_HandleTypeDef *huart);
/**
* @}
*/
/** @addtogroup UART_Exported_Functions_Group2
* @{
*/
/* IO operation functions *******************************************************/
HAL_StatusTypeDef HAL_UART_Transmit(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout);
HAL_StatusTypeDef HAL_UART_Receive(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout);
HAL_StatusTypeDef HAL_UART_Transmit_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
HAL_StatusTypeDef HAL_UART_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
HAL_StatusTypeDef HAL_UART_Transmit_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
HAL_StatusTypeDef HAL_UART_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
HAL_StatusTypeDef HAL_UART_DMAPause(UART_HandleTypeDef *huart);
HAL_StatusTypeDef HAL_UART_DMAResume(UART_HandleTypeDef *huart);
HAL_StatusTypeDef HAL_UART_DMAStop(UART_HandleTypeDef *huart);
void HAL_UART_IRQHandler(UART_HandleTypeDef *huart);
void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart);
void HAL_UART_TxHalfCpltCallback(UART_HandleTypeDef *huart);
void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart);
void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart);
void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart);
/**
* @}
*/
/** @addtogroup UART_Exported_Functions_Group3
* @{
*/
/* Peripheral Control functions ************************************************/
HAL_StatusTypeDef HAL_LIN_SendBreak(UART_HandleTypeDef *huart);
HAL_StatusTypeDef HAL_MultiProcessor_EnterMuteMode(UART_HandleTypeDef *huart);
HAL_StatusTypeDef HAL_MultiProcessor_ExitMuteMode(UART_HandleTypeDef *huart);
HAL_StatusTypeDef HAL_HalfDuplex_EnableTransmitter(UART_HandleTypeDef *huart);
HAL_StatusTypeDef HAL_HalfDuplex_EnableReceiver(UART_HandleTypeDef *huart);
/**
* @}
*/
/** @addtogroup UART_Exported_Functions_Group4
* @{
*/
/* Peripheral State functions **************************************************/
HAL_UART_StateTypeDef HAL_UART_GetState(UART_HandleTypeDef *huart);
uint32_t HAL_UART_GetError(UART_HandleTypeDef *huart);
/**
* @}
*/
/**
* @}
*/
/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/
/** @defgroup UART_Private_Constants UART Private Constants
* @{
*/
/** @brief UART interruptions flag mask
*
*/
#define UART_CR1_REG_INDEX 1
#define UART_CR2_REG_INDEX 2
#define UART_CR3_REG_INDEX 3
/**
* @}
*/
/* Private macros ------------------------------------------------------------*/
/** @defgroup UART_Private_Macros UART Private Macros
* @{
*/
#define IS_UART_WORD_LENGTH(LENGTH) (((LENGTH) == UART_WORDLENGTH_8B) || \
((LENGTH) == UART_WORDLENGTH_9B))
#define IS_UART_LIN_WORD_LENGTH(LENGTH) (((LENGTH) == UART_WORDLENGTH_8B))
#define IS_UART_STOPBITS(STOPBITS) (((STOPBITS) == UART_STOPBITS_1) || \
((STOPBITS) == UART_STOPBITS_2))
#define IS_UART_PARITY(PARITY) (((PARITY) == UART_PARITY_NONE) || \
((PARITY) == UART_PARITY_EVEN) || \
((PARITY) == UART_PARITY_ODD))
#define IS_UART_HARDWARE_FLOW_CONTROL(CONTROL)\
(((CONTROL) == UART_HWCONTROL_NONE) || \
((CONTROL) == UART_HWCONTROL_RTS) || \
((CONTROL) == UART_HWCONTROL_CTS) || \
((CONTROL) == UART_HWCONTROL_RTS_CTS))
#define IS_UART_MODE(MODE) ((((MODE) & (uint32_t)0x0000FFF3) == 0x00) && ((MODE) != (uint32_t)0x000000))
#define IS_UART_STATE(STATE) (((STATE) == UART_STATE_DISABLE) || \
((STATE) == UART_STATE_ENABLE))
#define IS_UART_OVERSAMPLING(SAMPLING) (((SAMPLING) == UART_OVERSAMPLING_16) || \
((SAMPLING) == UART_OVERSAMPLING_8))
#define IS_UART_LIN_OVERSAMPLING(SAMPLING) (((SAMPLING) == UART_OVERSAMPLING_16))
#define IS_UART_LIN_BREAK_DETECT_LENGTH(LENGTH) (((LENGTH) == UART_LINBREAKDETECTLENGTH_10B) || \
((LENGTH) == UART_LINBREAKDETECTLENGTH_11B))
#define IS_UART_WAKEUPMETHOD(WAKEUP) (((WAKEUP) == UART_WAKEUPMETHOD_IDLELINE) || \
((WAKEUP) == UART_WAKEUPMETHOD_ADDRESSMARK))
#define IS_UART_BAUDRATE(BAUDRATE) ((BAUDRATE) < 10500001)
#define IS_UART_ADDRESS(ADDRESS) ((ADDRESS) <= 0xF)
#define UART_DIV_SAMPLING16(_PCLK_, _BAUD_) (((_PCLK_)*25)/(4*(_BAUD_)))
#define UART_DIVMANT_SAMPLING16(_PCLK_, _BAUD_) (UART_DIV_SAMPLING16((_PCLK_), (_BAUD_))/100)
#define UART_DIVFRAQ_SAMPLING16(_PCLK_, _BAUD_) (((UART_DIV_SAMPLING16((_PCLK_), (_BAUD_)) - (UART_DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) * 100)) * 16 + 50) / 100)
#define UART_BRR_SAMPLING16(_PCLK_, _BAUD_) ((UART_DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) << 4)|(UART_DIVFRAQ_SAMPLING16((_PCLK_), (_BAUD_)) & 0x0F))
#define UART_DIV_SAMPLING8(_PCLK_, _BAUD_) (((_PCLK_)*25)/(2*(_BAUD_)))
#define UART_DIVMANT_SAMPLING8(_PCLK_, _BAUD_) (UART_DIV_SAMPLING8((_PCLK_), (_BAUD_))/100)
#define UART_DIVFRAQ_SAMPLING8(_PCLK_, _BAUD_) (((UART_DIV_SAMPLING8((_PCLK_), (_BAUD_)) - (UART_DIVMANT_SAMPLING8((_PCLK_), (_BAUD_)) * 100)) * 16 + 50) / 100)
#define UART_BRR_SAMPLING8(_PCLK_, _BAUD_) ((UART_DIVMANT_SAMPLING8((_PCLK_), (_BAUD_)) << 4)|(UART_DIVFRAQ_SAMPLING8((_PCLK_), (_BAUD_)) & 0x0F))
/**
* @}
*/
/* Private functions ---------------------------------------------------------*/
/** @defgroup UART_Private_Functions UART Private Functions
* @{
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* __STM32F4xx_HAL_UART_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

10
mbed-system_stm32f4xx.c
View File

@ -602,8 +602,9 @@ uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
/* The voltage scaling allows optimizing the power consumption when the device is
clocked below the maximum system frequency, to update the voltage scaling value
regarding system frequency refer to product datasheet. */
__PWR_CLK_ENABLE();
__HAL_PWR_VOLTAGESCALING_CONFIG((uint32_t)0x00000000);
__HAL_RCC_PWR_CLK_ENABLE();
PWR->CR &= PWR_CR_VOS;
PWR->CR |= 0x00000000;
/* Enable HSE oscillator and activate PLL with HSE as source */
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
@ -661,8 +662,9 @@ uint8_t SetSysClock_PLL_HSI(void)
/* The voltage scaling allows optimizing the power consumption when the device is
clocked below the maximum system frequency, to update the voltage scaling value
regarding system frequency refer to product datasheet. */
__PWR_CLK_ENABLE();
__HAL_PWR_VOLTAGESCALING_CONFIG((uint32_t)0x00000000);
__HAL_RCC_PWR_CLK_ENABLE();
PWR->CR &= PWR_CR_VOS;
PWR->CR |= 0x00000000;
/* Enable HSI oscillator and activate PLL with HSI as source */
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;

49
serial-stm32.c
View File

@ -18,8 +18,6 @@
See serial-avr.c for inspiration.
#endif
USART_TypeDef *port = USART2;
void serial_init()
{
// Enable TX/RX clock (GPIOA)
@ -34,29 +32,29 @@ void serial_init()
RXD_PORT->AFR[0] |= (((uint8_t)0x07) << ((RXD_PIN) << 2));
// MODER 2bits per channel
TXD_PORT->MODER |= (GPIO_MODE_AF_PP << ((TXD_PIN) << 1)); // set bit2: alternate function
RXD_PORT->MODER |= (GPIO_MODE_AF_PP << ((RXD_PIN) << 1));
TXD_PORT->MODER |= (2 << ((TXD_PIN) << 1)); // set bit2: alternate function
RXD_PORT->MODER |= (2 << ((RXD_PIN) << 1));
TXD_PORT->OSPEEDR |= GPIO_SPEED_HIGH << ((TXD_PIN) << 1);
RXD_PORT->OSPEEDR |= GPIO_SPEED_HIGH << ((RXD_PIN) << 1);
TXD_PORT->OSPEEDR |= (3 << ((TXD_PIN) << 1));
RXD_PORT->OSPEEDR |= (3 << ((RXD_PIN) << 1));
TXD_PORT->PUPDR |= (GPIO_PULLUP << ((TXD_PIN) << 1)); //Pullup
RXD_PORT->PUPDR |= (GPIO_PULLUP << ((RXD_PIN) << 1)); //Pullup? LPC has No Pull-up or Pull-down activation
TXD_PORT->PUPDR |= (1 << ((TXD_PIN) << 1)); //Pullup
RXD_PORT->PUPDR |= (1 << ((RXD_PIN) << 1)); //Pullup? LPC has No Pull-up or Pull-down activation
/* Disable the peripheral */
port->CR1 &= ~USART_CR1_UE;
USART2->CR1 &= ~USART_CR1_UE;
/* Set the UART Communication parameters */
/*-------------------------- USART CR2 Configuration -----------------------*/
/* Clear STOP[13:12] bits */
port->CR2 &= ~(USART_CR2_STOP);
USART2->CR2 &= ~(USART_CR2_STOP);
/* Configure the UART Stop Bits: Set STOP[13:12] bits according to huart->Init.StopBits value */
port->CR2 |= UART_STOPBITS_1;
USART2->CR2 |= 0x0000;
/*-------------------------- USART CR1 Configuration -----------------------*/
/* Clear M, PCE, PS, TE and RE bits */
port->CR1 &= ~(USART_CR1_M | USART_CR1_PCE | USART_CR1_PS | USART_CR1_TE | \
USART2->CR1 &= ~(USART_CR1_M | USART_CR1_PCE | USART_CR1_PS | USART_CR1_TE | \
USART_CR1_RE | USART_CR1_OVER8);
/* Configure the UART Word Length, Parity and mode:
@ -64,14 +62,19 @@ void serial_init()
Set PCE and PS bits according to huart->Init.Parity value
Set TE and RE bits according to huart->Init.Mode value
Set OVER8 bit according to huart->Init.OverSampling value */
port->CR1 |= UART_WORDLENGTH_8B | UART_PARITY_NONE | UART_MODE_TX_RX | UART_OVERSAMPLING_16;
// UART_WORDLENGTH_8B = 0x0000
// UART_PARITY_NONE = 0x0000
// UART_MODE_TX_RX = 0x000C
// UART_OVERSAMPLING_16 = 0x0000
USART2->CR1 |= USART_CR1_RE | USART_CR1_TE;
/*-------------------------- USART CR3 Configuration -----------------------*/
/* Clear CTSE and RTSE bits */
port->CR3 &= ~(USART_CR3_RTSE | USART_CR3_CTSE);
USART2->CR3 &= ~(USART_CR3_RTSE | USART_CR3_CTSE);
/* Configure the UART HFC: Set CTSE and RTSE bits according to huart->Init.HwFlowCtl value */
port->CR3 |= UART_HWCONTROL_NONE;
// UART_HWCONTROL_NONE = 0x0000
USART2->CR3 |= 0x0000;
/* 19.3.4 Fractional baud rate generation => reference manual for STM32F411
Set BRR for 115,200 Hz
@ -89,16 +92,16 @@ void serial_init()
#define FRACT_DIVIDER (INT_DIVIDER - (100 * (BAUD_H >> 4)))
#define BAUD_L (((((FRACT_DIVIDER * 16) + 50) / 100)) & 0X0F)
port->BRR = BAUD_H | BAUD_L;
USART2->BRR = BAUD_H | BAUD_L;
/* In asynchronous mode, the following bits must be kept cleared:
- LINEN and CLKEN bits in the USART_CR2 register,
- SCEN, HDSEL and IREN bits in the USART_CR3 register.*/
port->CR2 &= ~(USART_CR2_LINEN | USART_CR2_CLKEN);
port->CR3 &= ~(USART_CR3_SCEN | USART_CR3_HDSEL | USART_CR3_IREN);
USART2->CR2 &= ~(USART_CR2_LINEN | USART_CR2_CLKEN);
USART2->CR3 &= ~(USART_CR3_SCEN | USART_CR3_HDSEL | USART_CR3_IREN);
/* Enable the peripheral */
port->CR1 |= USART_CR1_UE;
USART2->CR1 |= USART_CR1_UE;
}
/** Check wether characters can be read.
@ -107,7 +110,7 @@ void serial_init()
in the line, but only wether there is at least one or not.
*/
uint8_t serial_rxchars(void) {
return port->SR & UART_FLAG_RXNE;
return USART2->SR & USART_SR_RXNE;
}
/** Read one character.
@ -116,7 +119,7 @@ uint8_t serial_popchar(void) {
uint8_t c = 0;
if (serial_rxchars())
c = (uint8_t)(port->DR & 0x1FF);
c = (uint8_t)(USART2->DR & 0x1FF);
return c;
}
@ -124,13 +127,13 @@ uint8_t serial_popchar(void) {
/** Check wether characters can be written
*/
uint8_t serial_txchars(void) {
return port->SR &UART_FLAG_TXE;
return USART2->SR &USART_SR_TXE;
}
/** Send one character.
*/
void serial_writechar(uint8_t data) {
while (!serial_txchars());
port->DR = (uint32_t)(data & 0x1FF);
USART2->DR = (uint32_t)(data & 0x1FF);
}
#endif /* defined TEACUP_C_INCLUDE && defined __ARM_STM32F411__ */