78 lines
2.9 KiB
C
78 lines
2.9 KiB
C
#ifndef _MACHINE_H
|
|
#define _MACHINE_H
|
|
|
|
// --------------------------------------------------------------------------
|
|
// values reflecting the gearing of your machine
|
|
// all numbers are integers, so no decimals, please :-)
|
|
|
|
// calculate these values appropriate for your machine
|
|
#define STEPS_PER_MM_X 320
|
|
#define STEPS_PER_MM_Y 320
|
|
#define STEPS_PER_MM_Z 320
|
|
|
|
// http://blog.arcol.hu/?p=157 may help with this next one
|
|
#define STEPS_PER_MM_E 320
|
|
|
|
// this is how many steps to suck back the filament by when we stop
|
|
#define E_STARTSTOP_STEPS 20
|
|
|
|
// --------------------------------------------------------------------------
|
|
// values depending on the capabilities of your stepper motors and other mechanics
|
|
// again, all numbers are integers
|
|
|
|
// used for G0 rapid moves and as a cap for all other feedrates
|
|
#define MAXIMUM_FEEDRATE_X 200
|
|
#define MAXIMUM_FEEDRATE_Y 200
|
|
#define MAXIMUM_FEEDRATE_Z 200
|
|
#define MAXIMUM_FEEDRATE_E 200
|
|
|
|
// used when searching endstops and similar
|
|
#define SEARCH_FEEDRATE_X 50
|
|
#define SEARCH_FEEDRATE_Y 50
|
|
#define SEARCH_FEEDRATE_Z 50
|
|
#define SEARCH_FEEDRATE_E 50
|
|
|
|
// extruder settings
|
|
#define TEMP_HYSTERESIS 20
|
|
#define TEMP_RESIDENCY_TIME 60
|
|
|
|
<<<<<<< HEAD:mendel/machine.h
|
|
// --------------------------------------------------------------------------
|
|
// you shouldn't need to edit something below this line
|
|
=======
|
|
#define STEPS_PER_MM_E ((uint32_t) ((E_STEPS_PER_REV * EXTRUDER_NOZZLE_DIAMETER / EXTRUDER_SHAFT_RADIUS / PI / EXTRUDER_INLET_DIAMETER) + 0.5))
|
|
>>>>>>> mendel-triffid:machine.h
|
|
|
|
// same as above with 25.4 scale factor
|
|
#define STEPS_PER_IN_X ((uint32_t) ((25.4 * STEPS_PER_MM_X) + 0.5))
|
|
#define STEPS_PER_IN_Y ((uint32_t) ((25.4 * STEPS_PER_MM_Y) + 0.5))
|
|
#define STEPS_PER_IN_Z ((uint32_t) ((25.4 * STEPS_PER_MM_Z) + 0.5))
|
|
#define STEPS_PER_IN_E ((uint32_t) ((25.4 * STEPS_PER_MM_E) + 0.5))
|
|
|
|
// inverse, used in distance calculation during DDA setup
|
|
#define UM_PER_STEP_X ((uint32_t) ((1000.0 / STEPS_PER_MM_X) + 0.5))
|
|
#define UM_PER_STEP_Y ((uint32_t) ((1000.0 / STEPS_PER_MM_Y) + 0.5))
|
|
#define UM_PER_STEP_Z ((uint32_t) ((1000.0 / STEPS_PER_MM_Z) + 0.5))
|
|
#define UM_PER_STEP_E ((uint32_t) ((1000.0 / STEPS_PER_MM_E) + 0.5))
|
|
|
|
|
|
/*
|
|
firmware build options
|
|
*/
|
|
|
|
// this option makes the step interrupt interruptible.
|
|
// this should help immensely with dropped serial characters, but may also make debugging infuriating due to the complexities arising from nested interrupts
|
|
#define STEP_INTERRUPT_INTERRUPTIBLE 1
|
|
|
|
// Xon/Xoff flow control. Should be redundant
|
|
// #define XONXOFF
|
|
|
|
/*
|
|
move buffer size, in number of moves
|
|
note that each move takes a fair chunk of ram (69 bytes as of this writing) so don't make the buffer too big - a bigger serial readbuffer may help more than increasing this unless your gcodes are more than 70 characters long on average.
|
|
however, a larger movebuffer will probably help with lots of short consecutive moves, as each move takes a bunch of math (hence time) to set up
|
|
*/
|
|
#define MOVEBUFFER_SIZE 8
|
|
|
|
#endif /* _MACHINE_H */
|