239 lines
8.1 KiB
C
239 lines
8.1 KiB
C
|
|
/***************************************************************************\
|
|
* *
|
|
* 1. CPU *
|
|
* *
|
|
\***************************************************************************/
|
|
|
|
/** \def CPU_TYPE
|
|
CPU types a user should be able to choose from in configtool. All
|
|
commented out.
|
|
*/
|
|
//#define CPU_TYPE atmega32u4
|
|
|
|
/** \def CPU
|
|
CPU actually present on the board.
|
|
*/
|
|
#define CPU atmega32u4
|
|
|
|
/** \def F_CPU_OPT
|
|
CPU clock frequencies a user should be able to choose from in configtool.
|
|
All commented out.
|
|
*/
|
|
//#define F_CPU_OPT 16000000UL
|
|
|
|
/** \def F_CPU
|
|
Actual CPU clock rate. #ifndef required for Arduino compatibility.
|
|
*/
|
|
#ifndef F_CPU
|
|
#define F_CPU 16000000UL
|
|
#endif
|
|
|
|
/** \def MOTHERBOARD
|
|
This is the motherboard, as opposed to the extruder. See extruder/ directory
|
|
for GEN3 extruder firmware.
|
|
*/
|
|
#define MOTHERBOARD
|
|
|
|
|
|
/***************************************************************************\
|
|
* *
|
|
* 2. PINOUTS *
|
|
* *
|
|
\***************************************************************************/
|
|
|
|
#include "../arduino.h"
|
|
|
|
#define X_STEP_PIN DIO18
|
|
#define X_DIR_PIN DIO17
|
|
#define X_MIN_PIN DIO1
|
|
//#define X_MAX_PIN DIO2
|
|
//#define X_ENABLE_PIN DIO29
|
|
//#define X_INVERT_DIR
|
|
//#define X_INVERT_MIN
|
|
//#define X_INVERT_MAX
|
|
//#define X_INVERT_ENABLE
|
|
|
|
#define Y_STEP_PIN DIO16
|
|
#define Y_DIR_PIN DIO15
|
|
#define Y_MIN_PIN DIO3
|
|
//#define Y_MAX_PIN DIO17
|
|
//#define Y_ENABLE_PIN DIO26
|
|
//#define Y_INVERT_DIR
|
|
//#define Y_INVERT_MIN
|
|
//#define Y_INVERT_MAX
|
|
//#define Y_INVERT_ENABLE
|
|
|
|
#define Z_STEP_PIN DIO14
|
|
#define Z_DIR_PIN DIO13
|
|
#define Z_MIN_PIN DIO2
|
|
//#define Z_MAX_PIN DIO19
|
|
//#define Z_ENABLE_PIN DIO23
|
|
//#define Z_INVERT_DIR
|
|
//#define Z_INVERT_MIN
|
|
//#define Z_INVERT_MAX
|
|
//#define Z_INVERT_ENABLE
|
|
|
|
#define E_STEP_PIN DIO12
|
|
#define E_DIR_PIN DIO11
|
|
//#define E_ENABLE_PIN DIO20
|
|
#define E_INVERT_DIR
|
|
//#define E_INVERT_ENABLE
|
|
|
|
//#define PS_ON_PIN DIO0
|
|
//#define PS_MOSFET_PIN DIO25
|
|
#define STEPPER_ENABLE_PIN DIO19
|
|
#define STEPPER_INVERT_ENABLE
|
|
|
|
/** \def DEBUG_LED_PIN
|
|
|
|
Enable flashing of a LED during motor stepping.
|
|
|
|
Disabled by default. Uncommenting this makes the binary a few bytes larger
|
|
and adds a few cycles to the step timing interrrupt in timer.c. Also used
|
|
for precision profiling (profiling works even without actually having such
|
|
a LED in hardware), see
|
|
http://reprap.org/wiki/Teacup_Firmware#Doing_precision_profiling
|
|
*/
|
|
//#define DEBUG_LED_PIN DIO13
|
|
|
|
|
|
/***************************************************************************\
|
|
* *
|
|
* 3. TEMPERATURE SENSORS *
|
|
* *
|
|
\***************************************************************************/
|
|
|
|
#ifndef DEFINE_TEMP_SENSOR
|
|
#define DEFINE_TEMP_SENSOR(...)
|
|
#endif
|
|
|
|
/** \def TEMP_MAX6675 TEMP_THERMISTOR TEMP_AD595 TEMP_PT100 TEMP_INTERCOM
|
|
Which temperature sensor types are you using? Leave all used ones
|
|
uncommented, comment out all others to save binary size and enhance
|
|
performance.
|
|
*/
|
|
//#define TEMP_MAX6675
|
|
#define TEMP_THERMISTOR
|
|
//#define TEMP_AD595
|
|
//#define TEMP_PT100
|
|
//#define TEMP_INTERCOM
|
|
|
|
/** \def TEMP_SENSOR_PIN
|
|
Temperature sensor pins a user should be able to choose from in configtool.
|
|
All commented out.
|
|
*/
|
|
//#define TEMP_SENSOR_PIN AIO0
|
|
//#define TEMP_SENSOR_PIN AIO1
|
|
|
|
/** \def DEFINE_TEMP_SENSOR
|
|
Define your temperature sensors here. One line for each sensor, only
|
|
limited by the number of available ATmega pins.
|
|
|
|
Types are same as TEMP_ list above - TT_MAX6675, TT_THERMISTOR, TT_AD595,
|
|
TT_PT100, TT_INTERCOM. See list in temp.c.
|
|
|
|
The "additional" field is used for TT_THERMISTOR only. It defines the
|
|
name of the table(s) in ThermistorTable.h to use. Typically, this is
|
|
THERMISTOR_EXTRUDER for the first or only table, or THERMISTOR_BED for
|
|
the second table.
|
|
|
|
For a GEN3 set temp_type to TT_INTERCOM and temp_pin to AIO0. The pin
|
|
won't be used in this case.
|
|
*/
|
|
//DEFINE_TEMP_SENSORS_START
|
|
// name type pin additional
|
|
DEFINE_TEMP_SENSOR(extruder, TT_THERMISTOR, AIO1, THERMISTOR_EXTRUDER)
|
|
DEFINE_TEMP_SENSOR(bed, TT_THERMISTOR, AIO0, THERMISTOR_BED)
|
|
|
|
// r0 beta r2 vadc
|
|
//TEMP_TABLE EXTRUDER (100000, 4092, 4700, 5.0)
|
|
//TEMP_TABLE BED (100000, 4092, 4700, 5.0)
|
|
//DEFINE_TEMP_SENSORS_END
|
|
|
|
|
|
/***************************************************************************\
|
|
* *
|
|
* 4. HEATERS *
|
|
* *
|
|
\***************************************************************************/
|
|
|
|
#ifndef DEFINE_HEATER
|
|
#define DEFINE_HEATER(...)
|
|
#endif
|
|
|
|
/** \def HEATER_PIN
|
|
Heater pins a user should be able to choose from in configtool. All
|
|
commented out.
|
|
*/
|
|
//#define HEATER_PIN DIO8
|
|
//#define HEATER_PIN DIO9
|
|
//#define HEATER_PIN DIO10
|
|
|
|
/** \def DEFINE_HEATER
|
|
Define your heaters and devices here.
|
|
|
|
To attach a heater to a temp sensor above, simply use exactly the same
|
|
name - copy+paste is your friend. Some common names are 'extruder',
|
|
'bed', 'fan', 'motor', ... names with special meaning can be found
|
|
in gcode_process.c. Currently, these are:
|
|
HEATER_extruder (M104)
|
|
HEATER_bed (M140)
|
|
HEATER_fan (M106)
|
|
|
|
Devices don't neccessarily have a temperature sensor, e.g. fans or
|
|
milling spindles. Operate such devices by setting their power (M106),
|
|
instead of setting their temperature (M104).
|
|
|
|
Also note, the index of a heater (M106 P#) can differ from the index of
|
|
its attached temperature sensor (M104 P#) in case sensor-less devices
|
|
are defined or the order of the definitions differs. The first defined
|
|
device has the index 0 (zero).
|
|
|
|
Set 'pwm' to ...
|
|
1 for using PWM on a PWM-able pin and on/off on other pins.
|
|
0 for using on/off on a PWM-able pin, too.
|
|
Using PWM usually gives smoother temperature control but can conflict
|
|
with slow switches, like solid state relays. PWM frequency can be
|
|
influenced globally with FAST_PWM, see below.
|
|
*/
|
|
//DEFINE_HEATERS_START
|
|
// name port pwm
|
|
DEFINE_HEATER(extruder, DIO10, 1)
|
|
DEFINE_HEATER(bed, DIO9, 1)
|
|
DEFINE_HEATER(fan, DIO8, 0)
|
|
|
|
#define HEATER_EXTRUDER HEATER_extruder
|
|
#define HEATER_BED HEATER_bed
|
|
#define HEATER_FAN HEATER_fan
|
|
//DEFINE_HEATERS_END
|
|
|
|
|
|
/***************************************************************************\
|
|
* *
|
|
* 5. COMMUNICATION OPTIONS *
|
|
* *
|
|
\***************************************************************************/
|
|
|
|
/** \def BAUD
|
|
Baud rate for the serial RS232 protocol connection to the host. Usually
|
|
115200, other common values are 19200, 38400 or 57600. Ignored when USB_SERIAL
|
|
is defined.
|
|
*/
|
|
//#define BAUD 115200
|
|
|
|
/** \def XONXOFF
|
|
Xon/Xoff flow control.
|
|
|
|
Redundant when using RepRap Host for sending G-code, but mandatory when
|
|
sending G-code files with a plain terminal emulator, like GtkTerm (Linux),
|
|
CoolTerm (Mac) or HyperTerminal (Windows).
|
|
*/
|
|
//#define XONXOFF
|
|
|
|
/** \def USB_SERIAL
|
|
Define this for using USB instead of the serial RS232 protocol. Works on
|
|
USB-equipped ATmegas, like the ATmega32U4, only.
|
|
*/
|
|
#define USB_SERIAL
|