326 lines
11 KiB
C
326 lines
11 KiB
C
|
|
/***************************************************************************\
|
|
* *
|
|
* 1. CPU *
|
|
* *
|
|
\***************************************************************************/
|
|
|
|
/** \def CPU_TYPE
|
|
CPU types a user should be able to choose from in configtool. All
|
|
commented out.
|
|
*/
|
|
//#define CPU_TYPE atmega644
|
|
//#define CPU_TYPE atmega644p
|
|
//#define CPU_TYPE atmega1284
|
|
//#define CPU_TYPE atmega1284p
|
|
|
|
/** \def CPU
|
|
CPU actually present on the board.
|
|
*/
|
|
#define CPU atmega1284p
|
|
|
|
/** \def F_CPU_OPT
|
|
CPU clock frequencies a user should be able to choose from in configtool.
|
|
All commented out.
|
|
*/
|
|
//#define F_CPU_OPT 16000000UL
|
|
|
|
/** \def F_CPU
|
|
Actual CPU clock rate. #ifndef required for Arduino compatibility.
|
|
*/
|
|
#ifndef F_CPU
|
|
#define F_CPU 16000000UL
|
|
#endif
|
|
|
|
/** \def MOTHERBOARD
|
|
This is the motherboard, as opposed to the extruder. See extruder/ directory
|
|
for GEN3 extruder firmware.
|
|
*/
|
|
#define MOTHERBOARD
|
|
|
|
|
|
/***************************************************************************\
|
|
* *
|
|
* 2. PINOUTS *
|
|
* *
|
|
\***************************************************************************/
|
|
|
|
//#define TX_ENABLE_PIN xxxx
|
|
//#define RX_ENABLE_PIN xxxx
|
|
|
|
#define X_STEP_PIN DIO15
|
|
#define X_DIR_PIN DIO21
|
|
#define X_MIN_PIN DIO18
|
|
//#define X_MAX_PIN DIO18
|
|
#define X_ENABLE_PIN DIO14
|
|
//#define X_INVERT_DIR
|
|
//#define X_INVERT_MIN
|
|
//#define X_INVERT_MAX
|
|
#define X_INVERT_ENABLE
|
|
|
|
#define Y_STEP_PIN DIO22
|
|
#define Y_DIR_PIN DIO23
|
|
#define Y_MIN_PIN DIO19
|
|
//#define Y_MAX_PIN DIO19
|
|
#define Y_ENABLE_PIN DIO14
|
|
//#define Y_INVERT_DIR
|
|
//#define Y_INVERT_MIN
|
|
//#define Y_INVERT_MAX
|
|
#define Y_INVERT_ENABLE
|
|
|
|
#define Z_STEP_PIN DIO3
|
|
#define Z_DIR_PIN DIO2
|
|
#define Z_MIN_PIN DIO20
|
|
//#define Z_MAX_PIN DIO20
|
|
#define Z_ENABLE_PIN DIO26
|
|
//#define Z_INVERT_DIR
|
|
//#define Z_INVERT_MIN
|
|
//#define Z_INVERT_MAX
|
|
#define Z_INVERT_ENABLE
|
|
|
|
#define E_STEP_PIN DIO1
|
|
#define E_DIR_PIN DIO0
|
|
#define E_ENABLE_PIN DIO14
|
|
//#define E_INVERT_DIR
|
|
#define E_INVERT_ENABLE
|
|
|
|
//#define PS_ON_PIN xxxx
|
|
//#define PS_INVERT_ON
|
|
//#define PS_MOSFET_PIN xxxx
|
|
//#define STEPPER_ENABLE_PIN xxxx
|
|
//#define STEPPER_INVERT_ENABLE
|
|
|
|
/** \def DEBUG_LED_PIN
|
|
|
|
Enable flashing of a LED during motor stepping.
|
|
|
|
Disabled by default. Uncommenting this makes the binary a few bytes larger
|
|
and adds a few cycles to the step timing interrrupt in timer.c. Also used
|
|
for precision profiling (profiling works even without actually having such
|
|
a LED in hardware), see
|
|
http://reprap.org/wiki/Teacup_Firmware#Doing_precision_profiling
|
|
*/
|
|
//#define DEBUG_LED_PIN DIO27
|
|
|
|
/** \def SD_CARD_SELECT_PIN
|
|
|
|
Chip Select pin of the SD card.
|
|
|
|
SD cards work over SPI and have a Chip Select or Slave Select (SS) pin.
|
|
Choose this pin according to where on the board your SD card adapter is
|
|
connected. Disabling this pin also disables SD card support and makes the
|
|
firmware binary about 4.5 kB smaller.
|
|
|
|
Connecting a device to SPI actually uses 4 signal lines, the other three
|
|
pins are choosen by Teacup automatically.
|
|
*/
|
|
#define SD_CARD_SELECT_PIN DIO31
|
|
|
|
/** \def MCP3008_SELECT_PIN
|
|
|
|
Chip Select pin of the MCP3008 ADC.
|
|
|
|
MCP3008/4 analog-digital converter works over SPI and has a Chip Select pin.
|
|
Choose this pin according to where the MCP3008 is connected. Setting this
|
|
pin is required only if at least one temperature sensor of type MCP3008 is
|
|
configured. Else it's ignored.
|
|
*/
|
|
//#define MCP3008_SELECT_PIN xxxx
|
|
|
|
|
|
/***************************************************************************\
|
|
* *
|
|
* 3. TEMPERATURE SENSORS *
|
|
* *
|
|
\***************************************************************************/
|
|
|
|
#ifndef DEFINE_TEMP_SENSOR
|
|
#define DEFINE_TEMP_SENSOR(...)
|
|
#endif
|
|
|
|
/** \def TEMP_MAX6675 TEMP_THERMISTOR TEMP_AD595 TEMP_PT100 TEMP_INTERCOM
|
|
\def TEMP_MCP3008
|
|
|
|
Which temperature sensor types are you using? Leave all used ones
|
|
uncommented, comment out all others to save binary size and enhance
|
|
performance.
|
|
*/
|
|
//#define TEMP_MAX6675
|
|
#define TEMP_THERMISTOR
|
|
//#define TEMP_AD595
|
|
//#define TEMP_PT100
|
|
//#define TEMP_INTERCOM
|
|
//#define TEMP_MCP3008
|
|
|
|
/** \def TEMP_SENSOR_PIN
|
|
Temperature sensor pins a user should be able to choose from in configtool.
|
|
All commented out.
|
|
*/
|
|
//#define TEMP_SENSOR_PIN AIO6
|
|
//#define TEMP_SENSOR_PIN AIO7
|
|
|
|
/** \def DEFINE_TEMP_SENSOR
|
|
Define your temperature sensors here. One line for each sensor, only
|
|
limited by the number of available ATmega pins.
|
|
|
|
Name must match the name of the corresponding heater. If a heater "extruder"
|
|
exists, a temperature sensor of that name has to exist as well. Same for
|
|
heater "bed". There can be one sensor without corresponding heater, name it
|
|
"noheater".
|
|
|
|
Types are same as TEMP_ list above - TT_MAX6675, TT_THERMISTOR, TT_AD595,
|
|
TT_PT100, TT_INTERCOM, TT_MCP3008. See list in temp.c.
|
|
|
|
The "additional" field is used for TT_THERMISTOR and TT_MCP3008 only. It
|
|
defines the name of the table(s) in thermistortable.h to use. This name is
|
|
arbitrary, often used names include THERMISTOR_EXTRUDER and THERMISTOR_BED.
|
|
Also, several sensors can share the same table, which saves binary size.
|
|
|
|
For a GEN3 set temp_type to TT_INTERCOM and temp_pin to AIO0. The pin
|
|
won't be used in this case.
|
|
*/
|
|
//DEFINE_TEMP_SENSORS_START
|
|
// name type pin additional
|
|
DEFINE_TEMP_SENSOR(extruder, TT_THERMISTOR, AIO7, THERMISTOR_EXTRUDER)
|
|
DEFINE_TEMP_SENSOR(bed, TT_THERMISTOR, AIO6, THERMISTOR_BED)
|
|
|
|
// Beta algorithm r0 beta r2 vadc
|
|
// Steinhart-Hart rp t0 r0 t1 r1 t2 r2
|
|
//TEMP_TABLE EXTRUDER (100000, 4092, 4700, 5.0)
|
|
//TEMP_TABLE BED (100000, 4092, 4700, 5.0)
|
|
//DEFINE_TEMP_SENSORS_END
|
|
|
|
|
|
/***************************************************************************\
|
|
* *
|
|
* 4. HEATERS *
|
|
* *
|
|
\***************************************************************************/
|
|
|
|
/** \def HEATER_PIN
|
|
Heater pins a user should be able to choose from in configtool. All
|
|
commented out.
|
|
*/
|
|
//#define HEATER_PIN DIO4
|
|
//#define HEATER_PIN DIO10
|
|
//#define HEATER_PIN DIO12
|
|
//#define HEATER_PIN DIO13
|
|
|
|
/** \def DEFINE_HEATER
|
|
Define your heaters and devices here.
|
|
|
|
To attach a heater to a temp sensor above, simply use exactly the same
|
|
name - copy+paste is your friend. Some common names are 'extruder',
|
|
'bed', 'fan', 'motor', ... names with special meaning can be found
|
|
in gcode_process.c. Currently, these are:
|
|
HEATER_extruder (M104)
|
|
HEATER_bed (M140)
|
|
HEATER_fan (M106)
|
|
|
|
Devices don't neccessarily have a temperature sensor, e.g. fans or
|
|
milling spindles. Operate such devices by setting their power (M106),
|
|
instead of setting their temperature (M104).
|
|
|
|
Also note, the index of a heater (M106 P#) can differ from the index of
|
|
its attached temperature sensor (M104 P#) in case sensor-less devices
|
|
are defined or the order of the definitions differs. The first defined
|
|
device has the index 0 (zero).
|
|
|
|
Set 'invert' to 0 for normal heaters. Setting it to 1 inverts the pin signal
|
|
for this pin, e.g. for a MOSFET with a driver.
|
|
|
|
Set 'pwm' to ...
|
|
1 for using PWM on a PWM-able pin and on/off on other pins.
|
|
0 for using on/off on a PWM-able pin, too.
|
|
|
|
Using PWM usually gives smoother temperature control but can conflict
|
|
with slow switches, like solid state relays. PWM frequency can be
|
|
influenced globally with FAST_PWM, see below.
|
|
*/
|
|
|
|
//DEFINE_HEATERS_START
|
|
|
|
// name pin invert pwm max_pwm
|
|
DEFINE_HEATER(extruder, DIO13, 0, 1, 100)
|
|
DEFINE_HEATER(bed, DIO12, 0, 1, 100)
|
|
DEFINE_HEATER(fan, DIO4, 0, 0, 100)
|
|
|
|
#define HEATER_EXTRUDER HEATER_extruder
|
|
#define HEATER_BED HEATER_bed
|
|
#define HEATER_FAN HEATER_fan
|
|
//DEFINE_HEATERS_END
|
|
|
|
|
|
/***************************************************************************\
|
|
* *
|
|
* 5. COMMUNICATION OPTIONS *
|
|
* *
|
|
\***************************************************************************/
|
|
|
|
/** \def BAUD
|
|
Baud rate for the serial RS232 protocol connection to the host. Usually
|
|
115200, other common values are 19200, 38400 or 57600. Ignored when USB_SERIAL
|
|
is defined.
|
|
*/
|
|
#define BAUD 115200
|
|
|
|
/** \def XONXOFF
|
|
Xon/Xoff flow control.
|
|
|
|
Redundant when using RepRap Host for sending G-code, but mandatory when
|
|
sending G-code files with a plain terminal emulator, like GtkTerm (Linux),
|
|
CoolTerm (Mac) or HyperTerminal (Windows).
|
|
*/
|
|
//#define XONXOFF
|
|
|
|
/** \def USB_SERIAL
|
|
Define this for using USB instead of the serial RS232 protocol. Works on
|
|
USB-equipped ATmegas, like the ATmega32U4, only.
|
|
*/
|
|
//#define USB_SERIAL
|
|
|
|
|
|
/***************************************************************************\
|
|
* *
|
|
* 6. DISPLAY SUPPORT *
|
|
* *
|
|
\***************************************************************************/
|
|
|
|
/** \def DISPLAY_BUS_4BIT DISPLAY_BUS_8BIT DISPLAY_BUS_I2C DISPLAY_BUS_SPI
|
|
|
|
The bus used to connect the display to the controller. This is a property
|
|
of the display. With most displays there can be only one correct choice.
|
|
|
|
Comment in the one in use, comment out all others. If there is no display,
|
|
comment out all of them to remove display code for better performance.
|
|
*/
|
|
//#define DISPLAY_BUS_4BIT
|
|
//#define DISPLAY_BUS_8BIT
|
|
//#define DISPLAY_BUS_I2C
|
|
//#define DISPLAY_BUS_SPI
|
|
|
|
/** \def DISPLAY_RS_PIN DISPLAY_RW_PIN DISPLAY_E_PIN
|
|
\def DISPLAY_D4_PIN DISPLAY_D5_PIN DISPLAY_D6_PIN DISPLAY_D7_PIN
|
|
|
|
Pins necessary for the 4-bit parallel display bus. Taken into account with
|
|
DISPLAY_BUS_4BIT defined, only.
|
|
*/
|
|
//#define DISPLAY_RS_PIN xxxx
|
|
//#define DISPLAY_RW_PIN xxxx
|
|
//#define DISPLAY_E_PIN xxxx
|
|
//#define DISPLAY_D4_PIN xxxx
|
|
//#define DISPLAY_D5_PIN xxxx
|
|
//#define DISPLAY_D6_PIN xxxx
|
|
//#define DISPLAY_D7_PIN xxxx
|
|
|
|
/** \def DISPLAY_TYPE_SSD1306 DISPLAY_TYPE_HD44780
|
|
|
|
The type of display in use. There can be only one choice. Taken into account
|
|
only if one of DISPLAY_BUS_xxx is defined.
|
|
|
|
Comment in the display in use, comment out all others. If there is no
|
|
display, comment out all of DISPLAY_BUS_xxx.
|
|
*/
|
|
//#define DISPLAY_TYPE_SSD1306
|
|
//#define DISPLAY_TYPE_HD44780
|