updates and minor changes in German/Dutch
minor changes in language_en.h to prevent langtool.pl warnings/errors
This commit is contained in:
3d-gussner
parent
67872b1027
commit
f82c2f84e5
|
|
@ -137,7 +137,7 @@ const char MSG_BED_CORRECTION_FRONT_IT[] PROGMEM = "Fronte [um]";
|
|||
const char MSG_BED_CORRECTION_FRONT_ES[] PROGMEM = "Adelante [um]";
|
||||
const char MSG_BED_CORRECTION_FRONT_PL[] PROGMEM = "Do przodu [um]";
|
||||
const char MSG_BED_CORRECTION_FRONT_DE[] PROGMEM = "Vorne [um]";
|
||||
const char MSG_BED_CORRECTION_FRONT_NL[] PROGMEM = "Vooruit[um]";
|
||||
const char MSG_BED_CORRECTION_FRONT_NL[] PROGMEM = "Voorruit [um]";
|
||||
const char * const MSG_BED_CORRECTION_FRONT_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_BED_CORRECTION_FRONT_EN,
|
||||
MSG_BED_CORRECTION_FRONT_CZ,
|
||||
|
|
@ -154,7 +154,7 @@ const char MSG_BED_CORRECTION_LEFT_IT[] PROGMEM = "Sinistra [um]";
|
|||
const char MSG_BED_CORRECTION_LEFT_ES[] PROGMEM = "Izquierda [um]";
|
||||
const char MSG_BED_CORRECTION_LEFT_PL[] PROGMEM = "W lewo [um]";
|
||||
const char MSG_BED_CORRECTION_LEFT_DE[] PROGMEM = "Links [um]";
|
||||
const char MSG_BED_CORRECTION_LEFT_NL[] PROGMEM = "Links [um]";
|
||||
const char MSG_BED_CORRECTION_LEFT_NL[] PROGMEM = "Links [um]";
|
||||
const char * const MSG_BED_CORRECTION_LEFT_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_BED_CORRECTION_LEFT_EN,
|
||||
MSG_BED_CORRECTION_LEFT_CZ,
|
||||
|
|
@ -188,7 +188,7 @@ const char MSG_BED_CORRECTION_REAR_IT[] PROGMEM = "Retro [um]";
|
|||
const char MSG_BED_CORRECTION_REAR_ES[] PROGMEM = "Atras [um]";
|
||||
const char MSG_BED_CORRECTION_REAR_PL[] PROGMEM = "Do tylu [um]";
|
||||
const char MSG_BED_CORRECTION_REAR_DE[] PROGMEM = "Hinten [um]";
|
||||
const char MSG_BED_CORRECTION_REAR_NL[] PROGMEM = "Achter [um]";
|
||||
const char MSG_BED_CORRECTION_REAR_NL[] PROGMEM = "Achter [um]";
|
||||
const char * const MSG_BED_CORRECTION_REAR_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_BED_CORRECTION_REAR_EN,
|
||||
MSG_BED_CORRECTION_REAR_CZ,
|
||||
|
|
@ -217,7 +217,7 @@ const char MSG_BED_CORRECTION_RIGHT_IT[] PROGMEM = "Destra [um]";
|
|||
const char MSG_BED_CORRECTION_RIGHT_ES[] PROGMEM = "Derecha [um]";
|
||||
const char MSG_BED_CORRECTION_RIGHT_PL[] PROGMEM = "W prawo [um]";
|
||||
const char MSG_BED_CORRECTION_RIGHT_DE[] PROGMEM = "Rechts [um]";
|
||||
const char MSG_BED_CORRECTION_RIGHT_NL[] PROGMEM = "Rechts [um]";
|
||||
const char MSG_BED_CORRECTION_RIGHT_NL[] PROGMEM = "Rechts [um]";
|
||||
const char * const MSG_BED_CORRECTION_RIGHT_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_BED_CORRECTION_RIGHT_EN,
|
||||
MSG_BED_CORRECTION_RIGHT_CZ,
|
||||
|
|
@ -284,7 +284,7 @@ const char MSG_BED_LEVELING_FAILED_POINT_LOW_CZ[] PROGMEM = "Kalibrace Z selhala
|
|||
const char MSG_BED_LEVELING_FAILED_POINT_LOW_IT[] PROGMEM = "Livellamento letto fallito.NoRispSensor Residui su ugello? In attesa di reset.";
|
||||
const char MSG_BED_LEVELING_FAILED_POINT_LOW_ES[] PROGMEM = "Nivelacion fallada. Sensor no funciona. Escombros en Boqui.? Esperando reset.";
|
||||
const char MSG_BED_LEVELING_FAILED_POINT_LOW_PL[] PROGMEM = "Kalibracja nieudana. Sensor nie dotknal. Zanieczysz. dysza? Czekam na reset.";
|
||||
const char MSG_BED_LEVELING_FAILED_POINT_LOW_DE[] PROGMEM = "Bett-Nivellierung fehlgeschlagen. Sensor wurde nicht ausgeloest. Schmutz auf der Duese? Warte auf Reset.";
|
||||
const char MSG_BED_LEVELING_FAILED_POINT_LOW_DE[] PROGMEM = "Bett-Nivellierung fehlgeschlagen. Sensor wurde nicht ausgeloest. Schmutzige Duese? Warte auf Reset.";
|
||||
const char MSG_BED_LEVELING_FAILED_POINT_LOW_NL[] PROGMEM = "Bed nivellering mislukt. Sensor was niet geactiveerd. Vuil op nozzle? Wacht op reset.";
|
||||
const char * const MSG_BED_LEVELING_FAILED_POINT_LOW_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_BED_LEVELING_FAILED_POINT_LOW_EN,
|
||||
|
|
@ -318,7 +318,7 @@ const char MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_BOTH_FAR_CZ[] PROGMEM = "K
|
|||
const char MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_BOTH_FAR_IT[] PROGMEM = "Calibrazione XYZ fallita. Punti anteriori non raggiungibili.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_BOTH_FAR_ES[] PROGMEM = "Calibracion XYZ fallad. Punto delanteros no alcanzables.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_BOTH_FAR_PL[] PROGMEM = "Kalibr. XYZ nieudana. Przed. punkty kalibr. zbyt do przodu. Wyrownac drukarke.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_BOTH_FAR_DE[] PROGMEM = "XYZ-Kalibrierung fehlgeschlagen. Vodere Kalibrierpunkte nicht erreichbar.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_BOTH_FAR_DE[] PROGMEM = "XYZ-Kalibrierung fehlgeschlagen. Vordere Kalibrierpunkte nicht erreichbar.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_BOTH_FAR_NL[] PROGMEM = "XYZ kalibratie mislukt. Voorzijde kalibratiepunten niet bereikbaar.";
|
||||
const char * const MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_BOTH_FAR_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_BOTH_FAR_EN,
|
||||
|
|
@ -352,7 +352,7 @@ const char MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_RIGHT_FAR_CZ[] PROGMEM = "
|
|||
const char MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_RIGHT_FAR_IT[] PROGMEM = "Calibrazione XYZ fallita. Punto anteriore destro non raggiungibile.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_RIGHT_FAR_ES[] PROGMEM = "Calibracion XYZ fallad. Punto delantero derecho no alcanzable.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_RIGHT_FAR_PL[] PROGMEM = "Kalibr. XYZ nieudana. Prawy przedni punkt zbyt do przodu. Wyrownac drukarke.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_RIGHT_FAR_DE[] PROGMEM = "XYZ-Kalibrierung fehlgeschlagen. Rechter voderer Kalibrierpunkt nicht erreichbar.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_RIGHT_FAR_DE[] PROGMEM = "XYZ-Kalibrierung fehlgeschlagen. Rechter vorderer Kalibrierpunkt nicht erreichbar.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_RIGHT_FAR_NL[] PROGMEM = "XYZ kalibratie mislukt. Rechtsvoor kalibratiepunt niet bereikbaar.";
|
||||
const char * const MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_RIGHT_FAR_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_RIGHT_FAR_EN,
|
||||
|
|
@ -420,8 +420,8 @@ const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME_CZ[] PROGMEM = "Kalibrace
|
|||
const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME_IT[] PROGMEM = "Calibrazion XYZ corretta. La distorsione verra' automaticamente compensata.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME_ES[] PROGMEM = "Calibracion XYZ correcta. La inclinacion se corregira automaticamente.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME_PL[] PROGMEM = "Kalibracja XYZ prawidlowa. Skosy beda automatycznie wyrownane przy druku.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME_DE[] PROGMEM = "X/Y sehr schief. Schiefheit wird automatisch korrigiert.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME_NL[] PROGMEM = "X/Y heel scheef. Scheefheid wordt automatisch gecorrigeerd.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME_DE[] PROGMEM = "XYZ-Kalibrierung ok. X/Y-Achsen sind sehr schief. Schiefheit wird automatisch korrigiert.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME_NL[] PROGMEM = "XYZ kalibratie ok. X/Y-assen zijn heel scheef. Scheefheid wordt automatisch gecorrigeerd.";
|
||||
const char * const MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME_EN,
|
||||
MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME_CZ,
|
||||
|
|
@ -437,8 +437,8 @@ const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD_CZ[] PROGMEM = "Kalibrace XYZ
|
|||
const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD_IT[] PROGMEM = "Calibrazion XYZ corretta. Assi X/Y leggermente storti. Ben fatto!";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD_ES[] PROGMEM = "Calibracion XYZ correcta. Los ejes X / Y estan ligeramente inclinados. Buen trabajo!";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD_PL[] PROGMEM = "Kalibracja XYZ prawidlowa. Osie X/Y lekko skosne. Dobra robota!";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD_DE[] PROGMEM = "XYZ Kalibrierung in Ordnung. X/Y Achsen sind etwas schief.";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD_NL[] PROGMEM = "XYZ kalibratie in orde. X/Y-assen zijn iets scheef. Good Job!";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD_DE[] PROGMEM = "XYZ-Kalibrierung ok. X/Y-Achsen sind etwas schief. Schiefheit wird automatisch korrigiert. Gut gemacht!";
|
||||
const char MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD_NL[] PROGMEM = "XYZ kalibratie ok. X/Y-assen zijn iets scheef. Scheefheid wordt automatisch gecorrigeerd. Goed gedaan!";
|
||||
const char * const MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD_EN,
|
||||
MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD_CZ,
|
||||
|
|
@ -547,7 +547,7 @@ const char MSG_CALIBRATE_E_CZ[] PROGMEM = "Kalibrovat E";
|
|||
const char MSG_CALIBRATE_E_IT[] PROGMEM = "Calibra E";
|
||||
const char MSG_CALIBRATE_E_ES[] PROGMEM = "Calibrar E";
|
||||
const char MSG_CALIBRATE_E_PL[] PROGMEM = "Kalibruj E";
|
||||
const char MSG_CALIBRATE_E_DE[] PROGMEM = "Kalibrierung E";
|
||||
const char MSG_CALIBRATE_E_DE[] PROGMEM = "Kalibriere E";
|
||||
const char MSG_CALIBRATE_E_NL[] PROGMEM = "Kalibratie E";
|
||||
const char * const MSG_CALIBRATE_E_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_CALIBRATE_E_EN,
|
||||
|
|
@ -598,7 +598,7 @@ const char MSG_CARD_MENU_CZ[] PROGMEM = "Tisk z SD";
|
|||
const char MSG_CARD_MENU_IT[] PROGMEM = "Stampa da SD";
|
||||
const char MSG_CARD_MENU_ES[] PROGMEM = "Menu tarjeta SD";
|
||||
const char MSG_CARD_MENU_PL[] PROGMEM = "Druk z SD";
|
||||
const char MSG_CARD_MENU_DE[] PROGMEM = "Druck von SD";
|
||||
const char MSG_CARD_MENU_DE[] PROGMEM = "Drucken von SD";
|
||||
const char MSG_CARD_MENU_NL[] PROGMEM = "Print van SD";
|
||||
const char * const MSG_CARD_MENU_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_CARD_MENU_EN,
|
||||
|
|
@ -666,7 +666,7 @@ const char MSG_CLEAN_NOZZLE_E_CZ[] PROGMEM = "E kalibrace ukoncena. Prosim ocist
|
|||
const char MSG_CLEAN_NOZZLE_E_IT[] PROGMEM = "Calibrazione E terminata. Si prega di pulire l'ugello. Click per continuare.";
|
||||
const char MSG_CLEAN_NOZZLE_E_ES[] PROGMEM = "E calibrado. Limpiar la boquilla. Haga clic una vez terminado.";
|
||||
const char MSG_CLEAN_NOZZLE_E_PL[] PROGMEM = "Kalibracja E skonczona. Prosze oczyscic dysze. Potem potwierdzic przyciskiem. ";
|
||||
const char MSG_CLEAN_NOZZLE_E_DE[] PROGMEM = "E-Kalibrierung beendet. Bitte reinigen Sie die Duese. Klicken wenn fertig";
|
||||
const char MSG_CLEAN_NOZZLE_E_DE[] PROGMEM = "E-Kalibrierung beendet. Bitte reinigen Sie die Duese. Klicken wenn fertig.";
|
||||
const char MSG_CLEAN_NOZZLE_E_NL[] PROGMEM = "E kalibratie voltooid. Reinig het tuit. Klik op als klaar.";
|
||||
const char * const MSG_CLEAN_NOZZLE_E_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_CLEAN_NOZZLE_E_EN,
|
||||
|
|
@ -710,7 +710,7 @@ const char MSG_CONFIRM_NOZZLE_CLEAN_CZ[] PROGMEM = "Pro uspesnou kalibraci ocist
|
|||
const char MSG_CONFIRM_NOZZLE_CLEAN_IT[] PROGMEM = "Pulire l'ugello per la calibrazione, poi fare click.";
|
||||
const char MSG_CONFIRM_NOZZLE_CLEAN_ES[] PROGMEM = "Limpiar boquilla para calibracion. Click cuando acabes.";
|
||||
const char MSG_CONFIRM_NOZZLE_CLEAN_PL[] PROGMEM = "Dla prawidl. kalibracji prosze oczyscic dysze. Potw. guzikiem.";
|
||||
const char MSG_CONFIRM_NOZZLE_CLEAN_DE[] PROGMEM = "Bitte reinigen Sie die Duese zur Kalibrierung. Klicken wenn fertig.";
|
||||
const char MSG_CONFIRM_NOZZLE_CLEAN_DE[] PROGMEM = "Bitte reinigen Sie die Duese zur Kalibrierung. Klicken wenn sauber.";
|
||||
const char MSG_CONFIRM_NOZZLE_CLEAN_NL[] PROGMEM = "Reinig het tuit voor de kalibratie aub. Klik als klaar.";
|
||||
const char * const MSG_CONFIRM_NOZZLE_CLEAN_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_CONFIRM_NOZZLE_CLEAN_EN,
|
||||
|
|
@ -727,7 +727,7 @@ const char MSG_CONFIRM_NOZZLE_CLEAN_FIL_ADJ_CZ[] PROGMEM = "Filamenty jsou srovn
|
|||
const char MSG_CONFIRM_NOZZLE_CLEAN_FIL_ADJ_IT[] PROGMEM = "I filamenti sono regolati. Si prega di pulire l'ugello per la calibrazione. Click per continuare.";
|
||||
const char MSG_CONFIRM_NOZZLE_CLEAN_FIL_ADJ_ES[] PROGMEM = "Filamentos ajustados. Limpie la boquilla para calibracion. Haga clic una vez terminado.";
|
||||
const char MSG_CONFIRM_NOZZLE_CLEAN_FIL_ADJ_PL[] PROGMEM = "Dla prawidlowej kalibracji prosze oczyscic dysze. Potem potwierdzic przyciskiem.";
|
||||
const char MSG_CONFIRM_NOZZLE_CLEAN_FIL_ADJ_DE[] PROGMEM = "Filamente sind jetzt eingestellt. Bitte reinigen Sie die Duese zur Kalibrierung. Klicken wenn fertig.";
|
||||
const char MSG_CONFIRM_NOZZLE_CLEAN_FIL_ADJ_DE[] PROGMEM = "Filamente sind jetzt eingestellt. Bitte reinigen Sie die Duese zur Kalibrierung. Klicken wenn sauber.";
|
||||
const char MSG_CONFIRM_NOZZLE_CLEAN_FIL_ADJ_NL[] PROGMEM = "Filamenten zijn nu ingesteld. Reinig het tuit voor de kalibratie. Klik als klaar.";
|
||||
const char * const MSG_CONFIRM_NOZZLE_CLEAN_FIL_ADJ_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_CONFIRM_NOZZLE_CLEAN_FIL_ADJ_EN,
|
||||
|
|
@ -788,7 +788,7 @@ const char MSG_DISABLE_STEPPERS_CZ[] PROGMEM = "Vypnout motory";
|
|||
const char MSG_DISABLE_STEPPERS_IT[] PROGMEM = "Disabilit motori";
|
||||
const char MSG_DISABLE_STEPPERS_ES[] PROGMEM = "Apagar motores";
|
||||
const char MSG_DISABLE_STEPPERS_PL[] PROGMEM = "Wylaczyc silniki";
|
||||
const char MSG_DISABLE_STEPPERS_DE[] PROGMEM = "Motoren deaktivieren";
|
||||
const char MSG_DISABLE_STEPPERS_DE[] PROGMEM = "Motoren aus";
|
||||
const char MSG_DISABLE_STEPPERS_NL[] PROGMEM = "Motoren uit";
|
||||
const char * const MSG_DISABLE_STEPPERS_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_DISABLE_STEPPERS_EN,
|
||||
|
|
@ -1127,7 +1127,7 @@ const char MSG_FIND_BED_OFFSET_AND_SKEW_LINE1_CZ[] PROGMEM = "Hledam kalibracni
|
|||
const char MSG_FIND_BED_OFFSET_AND_SKEW_LINE1_IT[] PROGMEM = "Ricerca del letto punto di calibraz.";
|
||||
const char MSG_FIND_BED_OFFSET_AND_SKEW_LINE1_ES[] PROGMEM = "Buscando cama punto de calibracion";
|
||||
const char MSG_FIND_BED_OFFSET_AND_SKEW_LINE1_PL[] PROGMEM = "Szukam punktu kalibracyjnego podkladki";
|
||||
const char MSG_FIND_BED_OFFSET_AND_SKEW_LINE1_DE[] PROGMEM = "Suche Bett Kalibrierungspunkt";
|
||||
const char MSG_FIND_BED_OFFSET_AND_SKEW_LINE1_DE[] PROGMEM = "Suche Bett Kalibrierpunkt";
|
||||
const char MSG_FIND_BED_OFFSET_AND_SKEW_LINE1_NL[] PROGMEM = "Zoeke bed kalibratiepunt";
|
||||
const char * const MSG_FIND_BED_OFFSET_AND_SKEW_LINE1_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_FIND_BED_OFFSET_AND_SKEW_LINE1_EN,
|
||||
|
|
@ -1465,8 +1465,8 @@ const char MSG_LOAD_ALL_CZ[] PROGMEM = "Zavest vse";
|
|||
const char MSG_LOAD_ALL_IT[] PROGMEM = "Caricare tutti";
|
||||
const char MSG_LOAD_ALL_ES[] PROGMEM = "Intr. todos fil.";
|
||||
const char MSG_LOAD_ALL_PL[] PROGMEM = "Zalad. wszystkie";
|
||||
const char MSG_LOAD_ALL_DE[] PROGMEM = "Lade alle";
|
||||
const char MSG_LOAD_ALL_NL[] PROGMEM = "Laad alle";
|
||||
const char MSG_LOAD_ALL_DE[] PROGMEM = "Alle laden";
|
||||
const char MSG_LOAD_ALL_NL[] PROGMEM = "Alle laden";
|
||||
const char * const MSG_LOAD_ALL_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_LOAD_ALL_EN,
|
||||
MSG_LOAD_ALL_CZ,
|
||||
|
|
@ -1488,7 +1488,7 @@ const char MSG_LOAD_FILAMENT_IT[] PROGMEM = "Carica filamento";
|
|||
const char MSG_LOAD_FILAMENT_ES[] PROGMEM = "Introducir filam.";
|
||||
const char MSG_LOAD_FILAMENT_PL[] PROGMEM = "Wprowadz filament";
|
||||
const char MSG_LOAD_FILAMENT_DE[] PROGMEM = "Filament laden";
|
||||
const char MSG_LOAD_FILAMENT_NL[] PROGMEM = "Laad Filament";
|
||||
const char MSG_LOAD_FILAMENT_NL[] PROGMEM = "Filament laden";
|
||||
const char * const MSG_LOAD_FILAMENT_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_LOAD_FILAMENT_EN,
|
||||
MSG_LOAD_FILAMENT_CZ,
|
||||
|
|
@ -1504,8 +1504,8 @@ const char MSG_LOAD_FILAMENT_1_CZ[] PROGMEM = "Zavest filament 1";
|
|||
const char MSG_LOAD_FILAMENT_1_IT[] PROGMEM = "Caricare fil. 1";
|
||||
const char MSG_LOAD_FILAMENT_1_ES[] PROGMEM = "Introducir fil. 1";
|
||||
const char MSG_LOAD_FILAMENT_1_PL[] PROGMEM = "Zaladowac fil. 1";
|
||||
const char MSG_LOAD_FILAMENT_1_DE[] PROGMEM = "Lade filament 1";
|
||||
const char MSG_LOAD_FILAMENT_1_NL[] PROGMEM = "Laad filament 1";
|
||||
const char MSG_LOAD_FILAMENT_1_DE[] PROGMEM = "Filament 1 laden";
|
||||
const char MSG_LOAD_FILAMENT_1_NL[] PROGMEM = "Filament 1 laden";
|
||||
const char * const MSG_LOAD_FILAMENT_1_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_LOAD_FILAMENT_1_EN,
|
||||
MSG_LOAD_FILAMENT_1_CZ,
|
||||
|
|
@ -1521,8 +1521,8 @@ const char MSG_LOAD_FILAMENT_2_CZ[] PROGMEM = "Zavest filament 2";
|
|||
const char MSG_LOAD_FILAMENT_2_IT[] PROGMEM = "Caricare fil. 2";
|
||||
const char MSG_LOAD_FILAMENT_2_ES[] PROGMEM = "Introducir fil. 2";
|
||||
const char MSG_LOAD_FILAMENT_2_PL[] PROGMEM = "Zaladowac fil. 2";
|
||||
const char MSG_LOAD_FILAMENT_2_DE[] PROGMEM = "Lade filament 2";
|
||||
const char MSG_LOAD_FILAMENT_2_NL[] PROGMEM = "Laad filament 2";
|
||||
const char MSG_LOAD_FILAMENT_2_DE[] PROGMEM = "Filament 2 laden";
|
||||
const char MSG_LOAD_FILAMENT_2_NL[] PROGMEM = "Filament 2 laden";
|
||||
const char * const MSG_LOAD_FILAMENT_2_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_LOAD_FILAMENT_2_EN,
|
||||
MSG_LOAD_FILAMENT_2_CZ,
|
||||
|
|
@ -1538,8 +1538,8 @@ const char MSG_LOAD_FILAMENT_3_CZ[] PROGMEM = "Zavest filament 3";
|
|||
const char MSG_LOAD_FILAMENT_3_IT[] PROGMEM = "Caricare fil. 3";
|
||||
const char MSG_LOAD_FILAMENT_3_ES[] PROGMEM = "Introducir fil. 3";
|
||||
const char MSG_LOAD_FILAMENT_3_PL[] PROGMEM = "Zaladowac fil. 3";
|
||||
const char MSG_LOAD_FILAMENT_3_DE[] PROGMEM = "Lade filament 3";
|
||||
const char MSG_LOAD_FILAMENT_3_NL[] PROGMEM = "Laad filament 3";
|
||||
const char MSG_LOAD_FILAMENT_3_DE[] PROGMEM = "Filament 3 laden";
|
||||
const char MSG_LOAD_FILAMENT_3_NL[] PROGMEM = "Filament 3 laden";
|
||||
const char * const MSG_LOAD_FILAMENT_3_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_LOAD_FILAMENT_3_EN,
|
||||
MSG_LOAD_FILAMENT_3_CZ,
|
||||
|
|
@ -1555,8 +1555,8 @@ const char MSG_LOAD_FILAMENT_4_CZ[] PROGMEM = "Zavest filament 4";
|
|||
const char MSG_LOAD_FILAMENT_4_IT[] PROGMEM = "Caricare fil. 4";
|
||||
const char MSG_LOAD_FILAMENT_4_ES[] PROGMEM = "Introducir fil. 4";
|
||||
const char MSG_LOAD_FILAMENT_4_PL[] PROGMEM = "Zaladowac fil. 4";
|
||||
const char MSG_LOAD_FILAMENT_4_DE[] PROGMEM = "Lade filament 4";
|
||||
const char MSG_LOAD_FILAMENT_4_NL[] PROGMEM = "Laad filament 4";
|
||||
const char MSG_LOAD_FILAMENT_4_DE[] PROGMEM = "Filament 4 laden";
|
||||
const char MSG_LOAD_FILAMENT_4_NL[] PROGMEM = "Filament 4 laden";
|
||||
const char * const MSG_LOAD_FILAMENT_4_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_LOAD_FILAMENT_4_EN,
|
||||
MSG_LOAD_FILAMENT_4_CZ,
|
||||
|
|
@ -1980,7 +1980,7 @@ const char MSG_NO_CARD_CZ[] PROGMEM = "Zadna SD karta";
|
|||
const char MSG_NO_CARD_IT[] PROGMEM = "Nessuna SD";
|
||||
const char MSG_NO_CARD_ES[] PROGMEM = "No hay tarjeta SD";
|
||||
const char MSG_NO_CARD_PL[] PROGMEM = "Brak karty SD";
|
||||
const char MSG_NO_CARD_DE[] PROGMEM = "Keine SD-Karte";
|
||||
const char MSG_NO_CARD_DE[] PROGMEM = "Keine SD Karte";
|
||||
const char MSG_NO_CARD_NL[] PROGMEM = "Geen SD kaart";
|
||||
const char * const MSG_NO_CARD_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_NO_CARD_EN,
|
||||
|
|
@ -2127,7 +2127,7 @@ const char * const MSG_PID_EXTRUDER_LANG_TABLE[LANG_NUM] PROGMEM = {
|
|||
MSG_PID_EXTRUDER_NL
|
||||
};
|
||||
|
||||
const char MSG_PID_FINISHED_EN[] PROGMEM = "PID cal. finished";
|
||||
const char MSG_PID_FINISHED_EN[] PROGMEM = "PID cal. finished ";
|
||||
const char MSG_PID_FINISHED_CZ[] PROGMEM = "PID kal. ukoncena";
|
||||
const char MSG_PID_FINISHED_IT[] PROGMEM = "Cal. PID completa";
|
||||
const char MSG_PID_FINISHED_ES[] PROGMEM = "Cal. PID terminada";
|
||||
|
|
@ -2144,7 +2144,7 @@ const char * const MSG_PID_FINISHED_LANG_TABLE[LANG_NUM] PROGMEM = {
|
|||
MSG_PID_FINISHED_NL
|
||||
};
|
||||
|
||||
const char MSG_PID_RUNNING_EN[] PROGMEM = "PID cal. ";
|
||||
const char MSG_PID_RUNNING_EN[] PROGMEM = "PID cal. ";
|
||||
const char MSG_PID_RUNNING_CZ[] PROGMEM = "PID kal. ";
|
||||
const char MSG_PID_RUNNING_IT[] PROGMEM = "Cal. PID";
|
||||
const char MSG_PID_RUNNING_ES[] PROGMEM = "Cal. PID ";
|
||||
|
|
@ -2183,7 +2183,7 @@ const char MSG_PINDA_PREHEAT_CZ[] PROGMEM = "Nahrivani PINDA";
|
|||
const char MSG_PINDA_PREHEAT_IT[] PROGMEM = "Riscald. PINDA";
|
||||
const char MSG_PINDA_PREHEAT_ES[] PROGMEM = "Calentando PINDA";
|
||||
const char MSG_PINDA_PREHEAT_PL[] PROGMEM = "Grzanie PINDA";
|
||||
const char MSG_PINDA_PREHEAT_DE[] PROGMEM = "PINDA heizt auf";
|
||||
const char MSG_PINDA_PREHEAT_DE[] PROGMEM = "PINDA aufwaremen";
|
||||
const char MSG_PINDA_PREHEAT_NL[] PROGMEM = "PINDA warmt op";
|
||||
const char * const MSG_PINDA_PREHEAT_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_PINDA_PREHEAT_EN,
|
||||
|
|
@ -2514,7 +2514,7 @@ const char MSG_SD_INSERTED_CZ[] PROGMEM = "Karta vlozena";
|
|||
const char MSG_SD_INSERTED_IT[] PROGMEM = "SD inserita";
|
||||
const char MSG_SD_INSERTED_ES[] PROGMEM = "Tarjeta insertada";
|
||||
const char MSG_SD_INSERTED_PL[] PROGMEM = "Karta wlozona";
|
||||
const char MSG_SD_INSERTED_DE[] PROGMEM = "SD-Karte erkannt";
|
||||
const char MSG_SD_INSERTED_DE[] PROGMEM = "SD Karte eingesetzt";
|
||||
const char MSG_SD_INSERTED_NL[] PROGMEM = "SD ingestoken";
|
||||
const char * const MSG_SD_INSERTED_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_SD_INSERTED_EN,
|
||||
|
|
@ -2551,7 +2551,7 @@ const char MSG_SD_REMOVED_CZ[] PROGMEM = "Karta vyjmuta";
|
|||
const char MSG_SD_REMOVED_IT[] PROGMEM = "SD rimossa";
|
||||
const char MSG_SD_REMOVED_ES[] PROGMEM = "Tarjeta retirada";
|
||||
const char MSG_SD_REMOVED_PL[] PROGMEM = "Karta wyjeta";
|
||||
const char MSG_SD_REMOVED_DE[] PROGMEM = "SD-Karte entfernt";
|
||||
const char MSG_SD_REMOVED_DE[] PROGMEM = "SD Karte entfernt";
|
||||
const char MSG_SD_REMOVED_NL[] PROGMEM = "SD verwijderd";
|
||||
const char * const MSG_SD_REMOVED_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_SD_REMOVED_EN,
|
||||
|
|
@ -2668,7 +2668,7 @@ const char MSG_SELFTEST_CHECK_HOTEND_CZ[] PROGMEM = "Kontrola hotend ";
|
|||
const char MSG_SELFTEST_CHECK_HOTEND_IT[] PROGMEM = "Verifica ugello";
|
||||
const char MSG_SELFTEST_CHECK_HOTEND_ES[] PROGMEM = "Control hotend ";
|
||||
const char MSG_SELFTEST_CHECK_HOTEND_PL[] PROGMEM = "Kontrola hotend ";
|
||||
const char MSG_SELFTEST_CHECK_HOTEND_DE[] PROGMEM = "Pruefe hotend ";
|
||||
const char MSG_SELFTEST_CHECK_HOTEND_DE[] PROGMEM = "Pruefe Hotend ";
|
||||
const char MSG_SELFTEST_CHECK_HOTEND_NL[] PROGMEM = "Controleer hotend ";
|
||||
const char * const MSG_SELFTEST_CHECK_HOTEND_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_SELFTEST_CHECK_HOTEND_EN,
|
||||
|
|
@ -2737,7 +2737,7 @@ const char MSG_SELFTEST_COOLING_FAN_IT[] PROGMEM = "Vent di stampa ant.?";;
|
|||
const char MSG_SELFTEST_COOLING_FAN_ES[] PROGMEM = "Vent. al frente?";;
|
||||
const char MSG_SELFTEST_COOLING_FAN_PL[] PROGMEM = "Przodni went. druku?";;
|
||||
const char MSG_SELFTEST_COOLING_FAN_DE[] PROGMEM = "Vorderer Luefter?";;
|
||||
const char MSG_SELFTEST_COOLING_FAN_NL[] PROGMEM = "Frontprint fan?";;
|
||||
const char MSG_SELFTEST_COOLING_FAN_NL[] PROGMEM = "Voordere fan?";;
|
||||
const char * const MSG_SELFTEST_COOLING_FAN_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_SELFTEST_COOLING_FAN_EN,
|
||||
MSG_SELFTEST_COOLING_FAN_CZ,
|
||||
|
|
@ -2811,7 +2811,7 @@ const char MSG_SELFTEST_EXTRUDER_FAN_IT[] PROGMEM = "Vent SX sull'ugello?";;
|
|||
const char MSG_SELFTEST_EXTRUDER_FAN_ES[] PROGMEM = "Vent. en la izg?";;
|
||||
const char MSG_SELFTEST_EXTRUDER_FAN_PL[] PROGMEM = "Lewy went na dysze?";;
|
||||
const char MSG_SELFTEST_EXTRUDER_FAN_DE[] PROGMEM = "Linker Luefter?";;
|
||||
const char MSG_SELFTEST_EXTRUDER_FAN_NL[] PROGMEM = "Linke Hotend fan?";;
|
||||
const char MSG_SELFTEST_EXTRUDER_FAN_NL[] PROGMEM = "Linke fan?";;
|
||||
const char * const MSG_SELFTEST_EXTRUDER_FAN_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_SELFTEST_EXTRUDER_FAN_EN,
|
||||
MSG_SELFTEST_EXTRUDER_FAN_CZ,
|
||||
|
|
@ -3066,13 +3066,14 @@ const char MSG_SILENT_MODE_OFF_CZ[] PROGMEM = "Mod [vys. vykon]";
|
|||
const char MSG_SILENT_MODE_OFF_IT[] PROGMEM = "Mode [forte]";
|
||||
const char MSG_SILENT_MODE_OFF_ES[] PROGMEM = "Modo [rend.pleno]";
|
||||
const char MSG_SILENT_MODE_OFF_PL[] PROGMEM = "Mod [w wydajnosc]";
|
||||
const char MSG_SILENT_MODE_OFF_DE[] PROGMEM = "Mode [Hohe Leist]";
|
||||
const char * const MSG_SILENT_MODE_OFF_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_SILENT_MODE_OFF_EN,
|
||||
MSG_SILENT_MODE_OFF_CZ,
|
||||
MSG_SILENT_MODE_OFF_IT,
|
||||
MSG_SILENT_MODE_OFF_ES,
|
||||
MSG_SILENT_MODE_OFF_PL,
|
||||
MSG_SILENT_MODE_OFF_EN,
|
||||
MSG_SILENT_MODE_OFF_DE,
|
||||
MSG_SILENT_MODE_OFF_EN
|
||||
};
|
||||
|
||||
|
|
@ -3102,7 +3103,7 @@ const char MSG_SPEED_CZ[] PROGMEM = "Rychlost";
|
|||
const char MSG_SPEED_IT[] PROGMEM = "Velocita";
|
||||
const char MSG_SPEED_ES[] PROGMEM = "Velocidad";
|
||||
const char MSG_SPEED_PL[] PROGMEM = "Predkosc";
|
||||
const char MSG_SPEED_DE[] PROGMEM = "Geschw.";
|
||||
const char MSG_SPEED_DE[] PROGMEM = "Geschwindigkeit";
|
||||
const char MSG_SPEED_NL[] PROGMEM = "Snelheid";
|
||||
const char * const MSG_SPEED_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_SPEED_EN,
|
||||
|
|
@ -3158,8 +3159,8 @@ const char MSG_STATS_PRINTTIME_CZ[] PROGMEM = "Cas tisku : ";
|
|||
const char MSG_STATS_PRINTTIME_IT[] PROGMEM = "Tempo di stampa:";
|
||||
const char MSG_STATS_PRINTTIME_ES[] PROGMEM = "Tiempo de imp.:";
|
||||
const char MSG_STATS_PRINTTIME_PL[] PROGMEM = "Czas druku : ";
|
||||
const char MSG_STATS_PRINTTIME_DE[] PROGMEM = "Druck Zeit: ";
|
||||
const char MSG_STATS_PRINTTIME_NL[] PROGMEM = "Print tijd: ";
|
||||
const char MSG_STATS_PRINTTIME_DE[] PROGMEM = "Druckzeit: ";
|
||||
const char MSG_STATS_PRINTTIME_NL[] PROGMEM = "Printtijd: ";
|
||||
const char * const MSG_STATS_PRINTTIME_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_STATS_PRINTTIME_EN,
|
||||
MSG_STATS_PRINTTIME_CZ,
|
||||
|
|
@ -3192,8 +3193,8 @@ const char MSG_STATS_TOTALPRINTTIME_CZ[] PROGMEM = "Celkovy cas :";
|
|||
const char MSG_STATS_TOTALPRINTTIME_IT[] PROGMEM = "Tempo stampa tot:";
|
||||
const char MSG_STATS_TOTALPRINTTIME_ES[] PROGMEM = "Tiempo total :";
|
||||
const char MSG_STATS_TOTALPRINTTIME_PL[] PROGMEM = "Czas calkowity :";
|
||||
const char MSG_STATS_TOTALPRINTTIME_DE[] PROGMEM = "Totale druck Zeit:";
|
||||
const char MSG_STATS_TOTALPRINTTIME_NL[] PROGMEM = "Total print tijd:";
|
||||
const char MSG_STATS_TOTALPRINTTIME_DE[] PROGMEM = "Totale Druckzeit:";
|
||||
const char MSG_STATS_TOTALPRINTTIME_NL[] PROGMEM = "Total printtijd:";
|
||||
const char * const MSG_STATS_TOTALPRINTTIME_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_STATS_TOTALPRINTTIME_EN,
|
||||
MSG_STATS_TOTALPRINTTIME_CZ,
|
||||
|
|
@ -3263,7 +3264,7 @@ const char * const MSG_SUPPORT_LANG_TABLE[LANG_NUM] PROGMEM = {
|
|||
const char MSG_SWITCH_PS_OFF_EN[] PROGMEM = "Switch power off";
|
||||
const char MSG_SWITCH_PS_OFF_CZ[] PROGMEM = "Zapnout zdroj";
|
||||
const char MSG_SWITCH_PS_OFF_PL[] PROGMEM = "Zapnout zdroj";
|
||||
const char MSG_SWITCH_PS_OFF_DE[] PROGMEM = "Netzteil aus";
|
||||
const char MSG_SWITCH_PS_OFF_DE[] PROGMEM = "Netzteil AUS";
|
||||
const char MSG_SWITCH_PS_OFF_NL[] PROGMEM = "Uitschakelen";
|
||||
const char * const MSG_SWITCH_PS_OFF_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_SWITCH_PS_OFF_EN,
|
||||
|
|
@ -3278,7 +3279,7 @@ const char * const MSG_SWITCH_PS_OFF_LANG_TABLE[LANG_NUM] PROGMEM = {
|
|||
const char MSG_SWITCH_PS_ON_EN[] PROGMEM = "Switch power on";
|
||||
const char MSG_SWITCH_PS_ON_CZ[] PROGMEM = "Vypnout zdroj";
|
||||
const char MSG_SWITCH_PS_ON_PL[] PROGMEM = "Vypnout zdroj";
|
||||
const char MSG_SWITCH_PS_ON_DE[] PROGMEM = "Netzteil ein";
|
||||
const char MSG_SWITCH_PS_ON_DE[] PROGMEM = "Netzteil EIN";
|
||||
const char MSG_SWITCH_PS_ON_NL[] PROGMEM = "Opstarten";
|
||||
const char * const MSG_SWITCH_PS_ON_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_SWITCH_PS_ON_EN,
|
||||
|
|
@ -3424,7 +3425,7 @@ const char MSG_TUNE_IT[] PROGMEM = "Regola";
|
|||
const char MSG_TUNE_ES[] PROGMEM = "Ajustar";
|
||||
const char MSG_TUNE_PL[] PROGMEM = "Nastroic";
|
||||
const char MSG_TUNE_DE[] PROGMEM = "Feineinstellung";
|
||||
const char MSG_TUNE_NL[] PROGMEM = "Aanpassen";
|
||||
const char MSG_TUNE_NL[] PROGMEM = "Fijninstellingen";
|
||||
const char * const MSG_TUNE_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_TUNE_EN,
|
||||
MSG_TUNE_CZ,
|
||||
|
|
@ -3462,8 +3463,8 @@ const char MSG_UNLOAD_ALL_CZ[] PROGMEM = "Vyjmout vse";
|
|||
const char MSG_UNLOAD_ALL_IT[] PROGMEM = "Rilasciare tutti";
|
||||
const char MSG_UNLOAD_ALL_ES[] PROGMEM = "Soltar todos fil.";
|
||||
const char MSG_UNLOAD_ALL_PL[] PROGMEM = "Wyjac wszystkie";
|
||||
const char MSG_UNLOAD_ALL_DE[] PROGMEM = "Entnehme alle";
|
||||
const char MSG_UNLOAD_ALL_NL[] PROGMEM = "Haal alle uit";
|
||||
const char MSG_UNLOAD_ALL_DE[] PROGMEM = "Alle entnehmen";
|
||||
const char MSG_UNLOAD_ALL_NL[] PROGMEM = "Alle uithalen";
|
||||
const char * const MSG_UNLOAD_ALL_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_UNLOAD_ALL_EN,
|
||||
MSG_UNLOAD_ALL_CZ,
|
||||
|
|
@ -3479,8 +3480,8 @@ const char MSG_UNLOAD_FILAMENT_CZ[] PROGMEM = "Vyjmout filament";
|
|||
const char MSG_UNLOAD_FILAMENT_IT[] PROGMEM = "Scarica filamento";
|
||||
const char MSG_UNLOAD_FILAMENT_ES[] PROGMEM = "Soltar filamento";
|
||||
const char MSG_UNLOAD_FILAMENT_PL[] PROGMEM = "Wyjac filament";
|
||||
const char MSG_UNLOAD_FILAMENT_DE[] PROGMEM = "Entnehme Filament";
|
||||
const char MSG_UNLOAD_FILAMENT_NL[] PROGMEM = "Haal Filament uit";
|
||||
const char MSG_UNLOAD_FILAMENT_DE[] PROGMEM = "Filament entnehmen";
|
||||
const char MSG_UNLOAD_FILAMENT_NL[] PROGMEM = "Filament uithalen";
|
||||
const char * const MSG_UNLOAD_FILAMENT_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_UNLOAD_FILAMENT_EN,
|
||||
MSG_UNLOAD_FILAMENT_CZ,
|
||||
|
|
@ -3496,8 +3497,8 @@ const char MSG_UNLOAD_FILAMENT_1_CZ[] PROGMEM = "Vyjmout filam. 1";
|
|||
const char MSG_UNLOAD_FILAMENT_1_IT[] PROGMEM = "Rilasciare fil. 1";
|
||||
const char MSG_UNLOAD_FILAMENT_1_ES[] PROGMEM = "Soltar fil. 1";
|
||||
const char MSG_UNLOAD_FILAMENT_1_PL[] PROGMEM = "Wyjac filament 1";
|
||||
const char MSG_UNLOAD_FILAMENT_1_DE[] PROGMEM = "Entnehme filament 1";
|
||||
const char MSG_UNLOAD_FILAMENT_1_NL[] PROGMEM = "Haal filament 1 uit";
|
||||
const char MSG_UNLOAD_FILAMENT_1_DE[] PROGMEM = "Filament 1 entnehmen";
|
||||
const char MSG_UNLOAD_FILAMENT_1_NL[] PROGMEM = "Filament 1 uithalen";
|
||||
const char * const MSG_UNLOAD_FILAMENT_1_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_UNLOAD_FILAMENT_1_EN,
|
||||
MSG_UNLOAD_FILAMENT_1_CZ,
|
||||
|
|
@ -3513,8 +3514,8 @@ const char MSG_UNLOAD_FILAMENT_2_CZ[] PROGMEM = "Vyjmout filam. 2";
|
|||
const char MSG_UNLOAD_FILAMENT_2_IT[] PROGMEM = "Rilasciare fil. 1";
|
||||
const char MSG_UNLOAD_FILAMENT_2_ES[] PROGMEM = "Soltar fil. 2";
|
||||
const char MSG_UNLOAD_FILAMENT_2_PL[] PROGMEM = "Wyjac filament 2";
|
||||
const char MSG_UNLOAD_FILAMENT_2_DE[] PROGMEM = "Entnehme filament 2";
|
||||
const char MSG_UNLOAD_FILAMENT_2_NL[] PROGMEM = "Haal filament 2 uit";
|
||||
const char MSG_UNLOAD_FILAMENT_2_DE[] PROGMEM = "Filament 2 entnehmen";
|
||||
const char MSG_UNLOAD_FILAMENT_2_NL[] PROGMEM = "Filament 2 uithalen";
|
||||
const char * const MSG_UNLOAD_FILAMENT_2_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_UNLOAD_FILAMENT_2_EN,
|
||||
MSG_UNLOAD_FILAMENT_2_CZ,
|
||||
|
|
@ -3530,8 +3531,8 @@ const char MSG_UNLOAD_FILAMENT_3_CZ[] PROGMEM = "Vyjmout filam. 3";
|
|||
const char MSG_UNLOAD_FILAMENT_3_IT[] PROGMEM = "Rilasciare fil. 1";
|
||||
const char MSG_UNLOAD_FILAMENT_3_ES[] PROGMEM = "Soltar fil. 3";
|
||||
const char MSG_UNLOAD_FILAMENT_3_PL[] PROGMEM = "Wyjac filament 3";
|
||||
const char MSG_UNLOAD_FILAMENT_3_DE[] PROGMEM = "Entnehme filament 3";
|
||||
const char MSG_UNLOAD_FILAMENT_3_NL[] PROGMEM = "Haal filament 3 uit";
|
||||
const char MSG_UNLOAD_FILAMENT_3_DE[] PROGMEM = "Filament 3 entnehmen";
|
||||
const char MSG_UNLOAD_FILAMENT_3_NL[] PROGMEM = "Filament 3 uithalen";
|
||||
const char * const MSG_UNLOAD_FILAMENT_3_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_UNLOAD_FILAMENT_3_EN,
|
||||
MSG_UNLOAD_FILAMENT_3_CZ,
|
||||
|
|
@ -3547,8 +3548,8 @@ const char MSG_UNLOAD_FILAMENT_4_CZ[] PROGMEM = "Vyjmout filam. 4";
|
|||
const char MSG_UNLOAD_FILAMENT_4_IT[] PROGMEM = "Rilasciare fil. 1";
|
||||
const char MSG_UNLOAD_FILAMENT_4_ES[] PROGMEM = "Soltar fil. 4";
|
||||
const char MSG_UNLOAD_FILAMENT_4_PL[] PROGMEM = "Wyjac filament 4";
|
||||
const char MSG_UNLOAD_FILAMENT_4_DE[] PROGMEM = "Entnehme filament 4";
|
||||
const char MSG_UNLOAD_FILAMENT_4_NL[] PROGMEM = "Haal filament 4 uit";
|
||||
const char MSG_UNLOAD_FILAMENT_4_DE[] PROGMEM = "Filament 4 entnehmen";
|
||||
const char MSG_UNLOAD_FILAMENT_4_NL[] PROGMEM = "Filament 4 uithalen";
|
||||
const char * const MSG_UNLOAD_FILAMENT_4_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_UNLOAD_FILAMENT_4_EN,
|
||||
MSG_UNLOAD_FILAMENT_4_CZ,
|
||||
|
|
@ -3615,7 +3616,7 @@ const char MSG_WAITING_TEMP_CZ[] PROGMEM = "Cekani na zchladnuti trysky a podloz
|
|||
const char MSG_WAITING_TEMP_IT[] PROGMEM = "In attesa del raffreddamento della testina e del piatto";
|
||||
const char MSG_WAITING_TEMP_ES[] PROGMEM = "Esperando enfriamiento de la cama y del extrusor.";
|
||||
const char MSG_WAITING_TEMP_PL[] PROGMEM = "Oczekiwanie na wychlodzenie dyszy i podkladki.";
|
||||
const char MSG_WAITING_TEMP_DE[] PROGMEM = "Warten auf Abkuehlung von Heater und Bett.";
|
||||
const char MSG_WAITING_TEMP_DE[] PROGMEM = "Warten auf Abkuehlung von Duese und Bett.";
|
||||
const char MSG_WAITING_TEMP_NL[] PROGMEM = "Wachten op afkoelen van heater en bed.";
|
||||
const char * const MSG_WAITING_TEMP_LANG_TABLE[LANG_NUM] PROGMEM = {
|
||||
MSG_WAITING_TEMP_EN,
|
||||
|
|
|
|||
|
|
@ -7,22 +7,22 @@
|
|||
*/
|
||||
|
||||
#define(length=20) WELCOME_MSG CUSTOM_MENDEL_NAME " bereit."
|
||||
#define MSG_SD_INSERTED "SD-Karte erkannt"
|
||||
#define MSG_SD_REMOVED "SD-Karte entfernt"
|
||||
#define MSG_SD_INSERTED "SD Karte eingesetzt"
|
||||
#define MSG_SD_REMOVED "SD Karte entfernt"
|
||||
#define MSG_MAIN "Hauptmenue"
|
||||
#define(length=20) MSG_DISABLE_STEPPERS "Motoren deaktivieren"
|
||||
#define(length=20) MSG_DISABLE_STEPPERS "Motoren aus"
|
||||
#define MSG_AUTO_HOME "Startposition"
|
||||
#define MSG_SET_HOME_OFFSETS "Setze Homeversatz"
|
||||
#define MSG_SET_ORIGIN "Setze Nullpunkt"
|
||||
#define MSG_COOLDOWN "Abkuehlen"
|
||||
#define MSG_SWITCH_PS_ON "Netzteil ein"
|
||||
#define MSG_SWITCH_PS_OFF "Netzteil aus"
|
||||
#define MSG_SWITCH_PS_ON "Netzteil EIN"
|
||||
#define MSG_SWITCH_PS_OFF "Netzteil AUS"
|
||||
#define MSG_MOVE_AXIS "Bewege Achse"
|
||||
#define MSG_MOVE_X "Bewege X"
|
||||
#define MSG_MOVE_Y "Bewege Y"
|
||||
#define MSG_MOVE_Z "Bewege Z"
|
||||
#define MSG_MOVE_E "Extruder"
|
||||
#define MSG_SPEED "Geschw."
|
||||
#define MSG_SPEED "Geschwindigkeit"
|
||||
#define MSG_NOZZLE "Duese"
|
||||
#define MSG_NOZZLE1 "Duese2"
|
||||
#define MSG_NOZZLE2 "Duese3"
|
||||
|
|
@ -49,8 +49,8 @@
|
|||
#define MSG_PAUSE_PRINT "Pause"
|
||||
#define MSG_RESUME_PRINT "Fortsetzen"
|
||||
#define MSG_STOP_PRINT "Druck abbrechen"
|
||||
#define MSG_CARD_MENU "Druck von SD"
|
||||
#define MSG_NO_CARD "Keine SD-Karte"
|
||||
#define MSG_CARD_MENU "Drucken von SD"
|
||||
#define MSG_NO_CARD "Keine SD Karte"
|
||||
#define MSG_DWELL "Warten..."
|
||||
#define(length=20) MSG_USERWAIT "Warte auf Nutzer..."
|
||||
#define(length=20) MSG_RESUMING "Druck fortgesetzt"
|
||||
|
|
@ -60,7 +60,7 @@
|
|||
#define MSG_STOPPED "GESTOPPT. "
|
||||
#define MSG_FILAMENTCHANGE "Filament-Wechsel"
|
||||
#define MSG_INIT_SDCARD "SD erkennen"
|
||||
#define MSG_CNG_SDCARD "SD-Karte wechsel"
|
||||
#define MSG_CNG_SDCARD "SD Karte wechsel"
|
||||
#define MSG_BABYSTEP_X "Babystep X"
|
||||
#define MSG_BABYSTEP_Y "Babystep Y"
|
||||
#define MSG_BABYSTEP_Z "Live Z einstellen"
|
||||
|
|
@ -69,18 +69,18 @@
|
|||
|
||||
#define MSG_SETTINGS "Einstellungen"
|
||||
#define MSG_PREHEAT "Vorheizen"
|
||||
#define MSG_UNLOAD_FILAMENT "Entnehme Filament"
|
||||
#define MSG_UNLOAD_FILAMENT "Filament entnehmen"
|
||||
#define MSG_LOAD_FILAMENT "Filament laden"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_1 "Lade filament 1"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_2 "Lade filament 2"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_3 "Lade filament 3"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_4 "Lade filament 4"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_1 "Entnehme filament 1"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_2 "Entnehme filament 2"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_3 "Entnehme filament 3"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_4 "Entnehme filament 4"
|
||||
#define MSG_UNLOAD_ALL "Entnehme alle"
|
||||
#define MSG_LOAD_ALL "Lade alle"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_1 "Filament 1 laden"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_2 "Filament 2 laden"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_3 "Filament 3 laden"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_4 "Filament 4 laden"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_1 "Filament 1 entnehmen"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_2 "Filament 2 entnehmen"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_3 "Filament 3 entnehmen"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_4 "Filament 4 entnehmen"
|
||||
#define(length=20) MSG_UNLOAD_ALL "Alle entnehmen"
|
||||
#define(length=20) MSG_LOAD_ALL "Alle laden"
|
||||
|
||||
#define MSG_RECTRACT "Rectract"
|
||||
#define MSG_ERROR "FEHLER:"
|
||||
|
|
@ -101,7 +101,7 @@
|
|||
|
||||
|
||||
#define MSG_SILENT_MODE_ON "Mode [leise]"
|
||||
#define MSG_SILENT_MODE_OFF "Mode [high power]"
|
||||
#define MSG_SILENT_MODE_OFF "Mode [Hohe Leist]"
|
||||
#define(length=20) MSG_REBOOT "Reboot den Drucker"
|
||||
#define(length=20, lines=2) MSG_TAKE_EFFECT " um wirksam zu werden"
|
||||
|
||||
|
|
@ -184,12 +184,12 @@
|
|||
#define(length=20) MSG_SELFTEST_FAN_NO "Dreht nicht";
|
||||
|
||||
#define(length=20) MSG_STATS_TOTALFILAMENT "Filament Gesamt:"
|
||||
#define(length=20) MSG_STATS_TOTALPRINTTIME "Totale druck Zeit:"
|
||||
#define(length=20) MSG_STATS_TOTALPRINTTIME "Totale Druckzeit:"
|
||||
#define(length=20) MSG_STATS_FILAMENTUSED "Filamentverbrauch:"
|
||||
#define(length=20) MSG_STATS_PRINTTIME "Druck Zeit: "
|
||||
#define(length=20) MSG_STATS_PRINTTIME "Druckzeit: "
|
||||
#define(length=20) MSG_SELFTEST_START "Selbsttest start "
|
||||
#define(length=20) MSG_SELFTEST_CHECK_ENDSTOPS "Pruefe Endschalter "
|
||||
#define(length=20) MSG_SELFTEST_CHECK_HOTEND "Pruefe hotend "
|
||||
#define(length=20) MSG_SELFTEST_CHECK_HOTEND "Pruefe Hotend "
|
||||
#define(length=20) MSG_SELFTEST_CHECK_X "Pruefe X Achse "
|
||||
#define(length=20) MSG_SELFTEST_CHECK_Y "Pruefe Y Achse "
|
||||
#define(length=20) MSG_SELFTEST_CHECK_Z "Pruefe Z Achse "
|
||||
|
|
@ -210,10 +210,10 @@
|
|||
#define(length=20, lines=8) MSG_MOVE_CARRIAGE_TO_THE_TOP "Kalibrieren von XYZ. Drehen Sie den Knopf, bis beide Z-Schlitten obere Anschaege erreichen. Klicken wenn beide ganz oben sind."
|
||||
#define(length=20, lines=8) MSG_MOVE_CARRIAGE_TO_THE_TOP_Z "Kalibrieren von Z. Drehen Sie den Knopf, bis beide Z-Schlitten obere Anschaege erreichen. Klicken wenn beide ganz oben sind."
|
||||
|
||||
#define(length=20, lines=8) MSG_CONFIRM_NOZZLE_CLEAN "Bitte reinigen Sie die Duese zur Kalibrierung. Klicken wenn fertig."
|
||||
#define(length=20, lines=8) MSG_CONFIRM_NOZZLE_CLEAN "Bitte reinigen Sie die Duese zur Kalibrierung. Klicken wenn sauber."
|
||||
#define(length=20, lines=8) MSG_CONFIRM_CARRIAGE_AT_THE_TOP "Sind beide Z Schlitten ganz oben?"
|
||||
|
||||
#define(length=60) MSG_FIND_BED_OFFSET_AND_SKEW_LINE1 "Suche Bett Kalibrierungspunkt"
|
||||
#define(length=60) MSG_FIND_BED_OFFSET_AND_SKEW_LINE1 "Suche Bett Kalibrierpunkt"
|
||||
#define(length=14) MSG_FIND_BED_OFFSET_AND_SKEW_LINE2 " von 4"
|
||||
#define(length=60) MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE1 "Genauigkeit verbessern bei Kalibrierpunkt"
|
||||
#define(length=14) MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE2 " von 9"
|
||||
|
|
@ -224,16 +224,16 @@
|
|||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_POINT_NOT_FOUND "XYZ-Kalibrierung fehlgeschlagen. Bett-Kalibrierpunkt nicht gefunden."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_FITTING_FAILED "XYZ-Kalibrierung fehlgeschlagen. Bitte schauen Sie in das Handbuch."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_PERFECT "XYZ-Kalibrierung ok. X/Y-Achsen sind senkrecht zueinander. Glueckwunsch!"
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD "XYZ Kalibrierung in Ordnung. X/Y Achsen sind etwas schief."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME "X/Y sehr schief. Schiefheit wird automatisch korrigiert."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD "XYZ-Kalibrierung ok. X/Y-Achsen sind etwas schief. Schiefheit wird automatisch korrigiert. Gut gemacht!"
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME "XYZ-Kalibrierung ok. X/Y-Achsen sind sehr schief. Schiefheit wird automatisch korrigiert."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_LEFT_FAR "XYZ-Kalibrierung fehlgeschlagen. Linker voderer Kalibrierpunkt nicht erreichbar."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_RIGHT_FAR "XYZ-Kalibrierung fehlgeschlagen. Rechter voderer Kalibrierpunkt nicht erreichbar."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_BOTH_FAR "XYZ-Kalibrierung fehlgeschlagen. Vodere Kalibrierpunkte nicht erreichbar."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_RIGHT_FAR "XYZ-Kalibrierung fehlgeschlagen. Rechter vorderer Kalibrierpunkt nicht erreichbar."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_BOTH_FAR "XYZ-Kalibrierung fehlgeschlagen. Vordere Kalibrierpunkte nicht erreichbar."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_LEFT_FAR "XYZ-Kalibrierung ungenau. Linker vorderer Kalibrierpunkt nicht erreichbar."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR "XYZ-Kalibrierung ungenau. Rechter vorderer Kalibrierpunkt nicht erreichbar."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR "XYZ-Kalibrierung ungenau. Vordere Kalibrierpunkte nicht erreichbar."
|
||||
|
||||
#define(length=20, lines=6) MSG_BED_LEVELING_FAILED_POINT_LOW "Bett-Nivellierung fehlgeschlagen. Sensor wurde nicht ausgeloest. Schmutz auf der Duese? Warte auf Reset."
|
||||
#define(length=20, lines=6) MSG_BED_LEVELING_FAILED_POINT_LOW "Bett-Nivellierung fehlgeschlagen. Sensor wurde nicht ausgeloest. Schmutzige Duese? Warte auf Reset."
|
||||
#define(length=20, lines=5) MSG_BED_LEVELING_FAILED_POINT_HIGH "Bett-Nivellierung fehlgeschlagen. Sensor wurde zu hoch ausgeloest. Warte auf Reset."
|
||||
#define(length=20, lines=6) MSG_BED_LEVELING_FAILED_PROBE_DISCONNECTED "Bett-Nivellierung fehlgeschlagen. Sensor nicht angeschlossen oder Kabel defekt. Warte auf Reset."
|
||||
|
||||
|
|
@ -252,16 +252,16 @@
|
|||
#define(length=20, lines=2) MSG_FIL_LOADED_CHECK "Ist Filament eingelegt?"
|
||||
#define(length=20, lines=3) MSG_FIL_TUNING "Knopf drehen um Filament einzustellen."
|
||||
#define(length=20, lines=4) MSG_FIL_ADJUSTING "Einstellen Filament. Bitte warten."
|
||||
#define(length=20, lines=8) MSG_CONFIRM_NOZZLE_CLEAN_FIL_ADJ "Filamente sind jetzt eingestellt. Bitte reinigen Sie die Duese zur Kalibrierung. Klicken wenn fertig."
|
||||
#define(length=20, lines=8) MSG_CONFIRM_NOZZLE_CLEAN_FIL_ADJ "Filamente sind jetzt eingestellt. Bitte reinigen Sie die Duese zur Kalibrierung. Klicken wenn sauber."
|
||||
#define(length=20, lines=4) MSG_STACK_ERROR "Error - static memory has been overwritten"
|
||||
#define(length=20, lines=1) MSG_CALIBRATE_E "Kalibrierung E"
|
||||
#define(length=20, lines=1) MSG_CALIBRATE_E "Kalibriere E"
|
||||
//#define(length=20, lines=1) MSG_RESET_CALIBRATE_E "Reset E Cal."
|
||||
#define(length=20, lines=8) MSG_E_CAL_KNOB "Knopf drehen bis die Filamentmarkierung erreicht ist. Klicken wenn fertig."
|
||||
|
||||
//#define(length=20, lines=1) MSG_FARM_CARD_MENU "Farm mode print"
|
||||
#define(length=20, lines=8) MSG_MARK_FIL "Filament 100mm vom Extrudergehaeuse markieren. Klicken wenn Fertig."
|
||||
#define(length=20, lines=8) MSG_CLEAN_NOZZLE_E "E-Kalibrierung beendet. Bitte reinigen Sie die Duese. Klicken wenn fertig"
|
||||
#define(length=20, lines=3) MSG_WAITING_TEMP "Warten auf Abkuehlung von Heater und Bett."
|
||||
#define(length=20, lines=8) MSG_CLEAN_NOZZLE_E "E-Kalibrierung beendet. Bitte reinigen Sie die Duese. Klicken wenn fertig."
|
||||
#define(length=20, lines=3) MSG_WAITING_TEMP "Warten auf Abkuehlung von Duese und Bett."
|
||||
#define(length=20, lines=2) MSG_FILAMENT_CLEAN "Ist Farbe rein?"
|
||||
#define(length=20) MSG_UNLOADING_FILAMENT "Filament auswerfen"
|
||||
#define(length=20, lines=10) MSG_PAPER "Lege waehrend der Kalibrierung der ersten 4 Punkte ein Blatt Papier unter die Duese. Wenn die Duese das Papier bewegt, Drucker sofort ausschalten!"
|
||||
|
|
@ -292,7 +292,7 @@
|
|||
#define MSG_CALIBRATE_PINDA "PINDA Temp. Kal."
|
||||
#define MSG_CALIBRATION_PINDA_MENU "PINDA Temp. Kal."
|
||||
#define(length=20, lines=3) MSG_PINDA_NOT_CALIBRATED "PINDA Temperatur Kalibrierung wurde noch nicht ausgefuehrt"
|
||||
#define MSG_PINDA_PREHEAT "PINDA heizt auf"
|
||||
#define MSG_PINDA_PREHEAT "PINDA aufwaremen"
|
||||
#define(length=20) MSG_TEMP_CALIBRATION "PINDA Temp.Kal. "
|
||||
#define(length=20, lines=3) MSG_TEMP_CALIBRATION_DONE "Die PINDA Temperaturkalibrierung ist beendet. Klicke um fortzufahren."
|
||||
#define(length=20) MSG_TEMP_CALIBRATION_ON "PINDA T.Kal. [ON]"
|
||||
|
|
|
|||
|
|
@ -7,7 +7,7 @@
|
|||
*/
|
||||
|
||||
#define(length=20) WELCOME_MSG CUSTOM_MENDEL_NAME " ready."
|
||||
#define MSG_SD_INSERTED "Card inserted"
|
||||
#define(length=20) MSG_SD_INSERTED "Card inserted"
|
||||
#define MSG_SD_REMOVED "Card removed"
|
||||
#define MSG_MAIN "Main"
|
||||
#define(length=20) MSG_DISABLE_STEPPERS "Disable steppers"
|
||||
|
|
@ -79,8 +79,8 @@
|
|||
#define(length=20) MSG_UNLOAD_FILAMENT_2 "Unload filament 2"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_3 "Unload filament 3"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_4 "Unload filament 4"
|
||||
#define MSG_UNLOAD_ALL "Unload all"
|
||||
#define MSG_LOAD_ALL "Load all"
|
||||
#define(length=20) MSG_UNLOAD_ALL "Unload all"
|
||||
#define(length=20) MSG_LOAD_ALL "Load all"
|
||||
|
||||
|
||||
#define MSG_RECTRACT "Rectract"
|
||||
|
|
@ -282,8 +282,8 @@
|
|||
#define(length=20, lines=1) MSG_RESUMING_PRINT "Resuming print"
|
||||
#define(length=20, lines=1) MSG_PID_EXTRUDER "PID calibration"
|
||||
#define(length=20, lines=1) MSG_SET_TEMPERATURE "Set temperature:"
|
||||
#define(length=20, lines=1) MSG_PID_FINISHED "PID cal. finished"
|
||||
#define(length=20, lines=1) MSG_PID_RUNNING "PID cal. "
|
||||
#define(length=20, lines=1) MSG_PID_FINISHED "PID cal. finished "
|
||||
#define(length=20, lines=1) MSG_PID_RUNNING "PID cal. "
|
||||
#define(length=20, lines=1) MSG_PID_BED "PID bed cal. "
|
||||
#define(length=20, lines=1) MSG_PID_BED_FINISHED "PID bed cal. done "
|
||||
#define(length=20, lines=1) MSG_PID_BED_RUNNING "PID bed cal. "
|
||||
|
|
|
|||
|
|
@ -45,7 +45,7 @@
|
|||
#define MSG_RESTORE_FAILSAFE "Backup terugzetten"
|
||||
#define MSG_REFRESH "\xF8" "Herladen"
|
||||
#define MSG_WATCH "Info scherm"
|
||||
#define MSG_TUNE "Aanpassen"
|
||||
#define MSG_TUNE "Fijninstellingen"
|
||||
#define MSG_PAUSE_PRINT "Print pauzeren"
|
||||
#define MSG_RESUME_PRINT "Print hervatten"
|
||||
#define MSG_STOP_PRINT "Print stoppen"
|
||||
|
|
@ -69,18 +69,18 @@
|
|||
|
||||
#define MSG_SETTINGS "Instellingen"
|
||||
#define MSG_PREHEAT "Voorverwarmen"
|
||||
#define MSG_UNLOAD_FILAMENT "Haal Filament uit"
|
||||
#define MSG_LOAD_FILAMENT "Laad Filament"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_1 "Laad filament 1"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_2 "Laad filament 2"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_3 "Laad filament 3"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_4 "Laad filament 4"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_1 "Haal filament 1 uit"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_2 "Haal filament 2 uit"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_3 "Haal filament 3 uit"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_4 "Haal filament 4 uit"
|
||||
#define MSG_UNLOAD_ALL "Haal alle uit"
|
||||
#define MSG_LOAD_ALL "Laad alle"
|
||||
#define MSG_UNLOAD_FILAMENT "Filament uithalen"
|
||||
#define MSG_LOAD_FILAMENT "Filament laden"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_1 "Filament 1 laden"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_2 "Filament 2 laden"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_3 "Filament 3 laden"
|
||||
#define(length=20) MSG_LOAD_FILAMENT_4 "Filament 4 laden"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_1 "Filament 1 uithalen"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_2 "Filament 2 uithalen"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_3 "Filament 3 uithalen"
|
||||
#define(length=20) MSG_UNLOAD_FILAMENT_4 "Filament 4 uithalen"
|
||||
#define(length=20) MSG_UNLOAD_ALL "Alle uithalen"
|
||||
#define(length=20) MSG_LOAD_ALL "Alle laden"
|
||||
|
||||
#define MSG_RECTRACT "Rectract"
|
||||
#define MSG_ERROR "FOUT:"
|
||||
|
|
@ -177,15 +177,15 @@
|
|||
#define(length=20) MSG_LOOSE_PULLEY "Loose pulley"
|
||||
|
||||
#define MSG_SELFTEST_FAN "Fan test";
|
||||
#define(length=20) MSG_SELFTEST_COOLING_FAN "Frontprint fan?";
|
||||
#define(length=20) MSG_SELFTEST_EXTRUDER_FAN "Linke Hotend fan?";
|
||||
#define(length=20) MSG_SELFTEST_COOLING_FAN "Voordere fan?";
|
||||
#define(length=20) MSG_SELFTEST_EXTRUDER_FAN "Linke fan?";
|
||||
#define MSG_SELFTEST_FAN_YES "Roteert";
|
||||
#define(length=20) MSG_SELFTEST_FAN_NO "Roteert niet";
|
||||
|
||||
#define(length=20) MSG_STATS_TOTALFILAMENT "Filament total: "
|
||||
#define(length=20) MSG_STATS_TOTALPRINTTIME "Total print tijd:"
|
||||
#define(length=20) MSG_STATS_TOTALPRINTTIME "Total printtijd:"
|
||||
#define(length=20) MSG_STATS_FILAMENTUSED "Filamentverbruik:"
|
||||
#define(length=20) MSG_STATS_PRINTTIME "Print tijd: "
|
||||
#define(length=20) MSG_STATS_PRINTTIME "Printtijd: "
|
||||
#define(length=20) MSG_SELFTEST_START "Zelftest start "
|
||||
#define(length=20) MSG_SELFTEST_CHECK_ENDSTOPS "Controleer endstops"
|
||||
#define(length=20) MSG_SELFTEST_CHECK_HOTEND "Controleer hotend "
|
||||
|
|
@ -223,8 +223,8 @@
|
|||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_POINT_NOT_FOUND "XYZ kalibratie mislukt. Bed kalibratiepunt niet gevonden."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_FITTING_FAILED "XYZ kalibratie mislukt. Raadpleeg de handleiding."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_PERFECT "XYZ kalibratie ok. X/Y-assen staan perpendiculair. Gefeliciteerd!"
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD "XYZ kalibratie in orde. X/Y-assen zijn iets scheef. Good Job!"
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME "X/Y heel scheef. Scheefheid wordt automatisch gecorrigeerd."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD "XYZ kalibratie ok. X/Y-assen zijn iets scheef. Scheefheid wordt automatisch gecorrigeerd. Goed gedaan!"
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME "XYZ kalibratie ok. X/Y-assen zijn heel scheef. Scheefheid wordt automatisch gecorrigeerd."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_LEFT_FAR "XYZ kalibratie mislukt. Linksvoor kalibratiepunt niet bereikbaar."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_RIGHT_FAR "XYZ kalibratie mislukt. Rechtsvoor kalibratiepunt niet bereikbaar."
|
||||
#define(length=20, lines=8) MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_BOTH_FAR "XYZ kalibratie mislukt. Voorzijde kalibratiepunten niet bereikbaar."
|
||||
|
|
@ -266,10 +266,10 @@
|
|||
#define(length=20, lines=10) MSG_PAPER "Leg een vel papier onder het tuit tijdens de kalibratie van de eerste 4 punten. Als het tuit het papier vangt, Printer onmiddellijk uitschakelen."
|
||||
|
||||
#define(length=20) MSG_BED_CORRECTION_MENU "Bed juist"
|
||||
#define MSG_BED_CORRECTION_LEFT "Links [um]"
|
||||
#define MSG_BED_CORRECTION_RIGHT "Rechts [um]"
|
||||
#define MSG_BED_CORRECTION_FRONT "Vooruit[um]"
|
||||
#define MSG_BED_CORRECTION_REAR "Achter [um]"
|
||||
#define MSG_BED_CORRECTION_LEFT "Links [um]"
|
||||
#define MSG_BED_CORRECTION_RIGHT "Rechts [um]"
|
||||
#define MSG_BED_CORRECTION_FRONT "Voorruit [um]"
|
||||
#define MSG_BED_CORRECTION_REAR "Achter [um]"
|
||||
#define MSG_BED_CORRECTION_RESET "Reset"
|
||||
|
||||
#define MSG_MESH_BED_LEVELING "Mesh Bed Leveling"
|
||||
|
|
|
|||
Loading…
Reference in New Issue