414972c876
Unbreak build with !PINDA_THERMISTOR
2022-12-30 14:14:01 +01:00
7828788e5c
Handle CALIBRATION_STATUS_TEMP_MODEL
2022-12-30 14:14:01 +01:00
2a13ce4c62
Handle CALIBRATION_STATUS_SELFTEST
2022-12-30 14:14:01 +01:00
b41ece175b
Handle CALIBRATION_STATUS_LIVE_ADJUST
2022-12-30 14:14:01 +01:00
22c0e15047
wizard: Rewrite the wizard handling loop
...
Simplify status tracking:
- S::Restore to continue to the next logical wizard item
- S::Finish for a successful failure
- S::Failed to exit while showing a failure
2022-12-30 14:14:01 +01:00
4219beed71
Remove initial cursor setting
...
The cursor position is controlled by
the for-loop
Change in memory:
Flash: -8 bytes
SRAM: 0 bytes
2022-12-30 12:57:07 +01:00
1186b36bfa
Remove whitespace at start of new row
2022-12-30 12:57:07 +01:00
7529eaec44
Remove duplicate code
...
msg_next is NULL, then the end of the message has been reached.
Change in memory:
Flash: -24 bytes
SRAM: 0 bytes
2022-12-30 12:57:07 +01:00
5037d1edbc
delay_keep_alive calls manage_heater and manage_inactivity
...
No need to call them again, the for-loop is very quick
Change in memory:
Flash: -10 bytes
SRAM: 0 bytes
2022-12-30 12:57:07 +01:00
1a9b7d79e6
Don't handle whitespace in a special way
...
Instead of reading and checking if a character is a whitespace
just print it out onto the LCD. This makes the code a bit less
complex. Whether there is a whitespace character, we always end
up reading from program space, so I doubt this has much performance
impact.
Change in memory:
Flash: -38 bytes
SRAM: 0 bytes
2022-12-30 12:57:07 +01:00
96707aadcb
Fix timeout making UI freeze
2022-12-30 12:49:57 +01:00
b3790f4094
Typo: meassure -> measure
2022-12-22 12:54:42 +01:00
9ca7760c2e
Merge pull request #3830 from 3d-gussner/MK3_XYZ_cal_fix
...
MK3: XYZ cal change message and add LCD ouput
2022-12-20 14:16:49 +01:00
0bcb4ab59d
Merge pull request #3822 from wavexx/tm_partial_lock
...
MK3: TM: Prevent lockout on invalid model values
2022-12-20 14:13:56 +01:00
7fef570d1b
Change xyz cal message `up to 24 min.` instead `approx. 12 min.`
2022-12-20 10:30:53 +01:00
65f5b9e53d
Merge pull request #3818 from wavexx/tm_default_state
...
TM: Provide full defaults for model data and enable it by default
2022-12-20 07:08:25 +01:00
dba3428ef2
Improve MSG_ACK_ERROR message
2022-12-17 20:25:47 +01:00
80c7790e87
Also prevent longpress when Stopped
2022-12-17 17:30:44 +01:00
271523ad45
TM: Disallow preheat/filament actions when stopped
...
Require acknowledgement first
2022-12-17 17:00:33 +01:00
f8290f25cd
TM: Allow to resume without a running print
...
If there is no running print, and the printer is Stopped, add a new
"Acknowledge error" menu entry to unlock the printer.
This simply calls lcd_print_stop(), which is identical in behavior to a
thermal error with a running print.
2022-12-17 16:48:39 +01:00
8d719efa79
Do not show/call LCD status updates when unchanged
...
This mostly prevents useless serial noise
2022-12-17 16:35:26 +01:00
6e2f016655
TM: Clear the Stopped state when stopping the current print
...
We allow resuming from the LCD via start print and resume print,
it makes sense to clear the error on stop too.
For this reason distinguish whether the action is performed
automatically or manually (ie: interactively).
The error is only cleared when the command is run interactively.
2022-12-17 16:11:31 +01:00
119dc10b8f
Rename print_stop() to lcd_print_stop_finish() for clarity
2022-12-17 16:03:03 +01:00
2e7c237a17
Cleanup: remove automatic parameter from unload_filament()
...
In M600 and M702, the Z-lift is taken care of outside this function
so it makes no sense to have a Z-lift within unload_filament()
Only exception to this is in the wizard, there I moved the Z-lift to
happen before we start heating the nozzle.
Change in memory:
Flash: -12 bytes
SRAM: 0 bytes
2022-12-16 16:20:09 +01:00
090c72367d
Minor Fix for PR2235
...
Shorten message to c=12 as some translation of `Yes/No` are 4 chars long
2022-12-16 16:10:15 +01:00
74545e2133
Fix `µ` character shown on translations
2022-12-16 15:59:37 +01:00
36575a4f83
Restore the previous model state when performing a nozzle change
...
Do not force-enable the model if it was previously disabled.
2022-12-12 20:17:56 +01:00
c5ec77a1ce
wizard: Allow finishing the calibration through menus
...
If the wizard is interrupted during model calibration, allow the
menu to mark "temperature model" calibration as complete.
2022-12-12 18:25:17 +01:00
118b39da39
wizard: Rework the thermal model calibration logic
...
- Correctly sequence the enqueued commands in order to check for the
real calibration result.
- Perform autocalibration with self-check enabled.
- Only save/continue the wizard if autocalibration succeeds.
2022-12-12 18:25:07 +01:00
38d893589f
selftest: Handle thermal errors in lcd_selfcheck_check_heater
...
- Simplify lcd_selfcheck_check_heater loop
- Check for/abort on Stopped (indicating a thermal failure).
2022-12-12 18:24:58 +01:00
613ea290f5
Add a comment
2022-12-10 10:04:17 +00:00
9ed46df97f
Don't show full screen message meant for single color setup
...
load_filament_to_nozzle will show a more precise full screen message when an MMU is used.
2022-12-10 10:00:58 +00:00
1e39012953
Merge pull request #3793 from gudnimg/PFW-1453
...
PFW-1453 Stop Print: Don't unload if FINDA is not triggered
2022-12-09 12:54:16 +00:00
68c5cdce1c
Merge pull request #3780 from gudnimg/stop-print-optimisations
...
optimisation: Improve Stop Print menu
2022-12-08 19:41:52 +01:00
92f2281b1a
Merge pull request #2335 from Panayiotis-git/MK3_NoBedHeating_onLoadUnload
...
@Panayiotis-git Thanks a lot!
Finally after 3 years 21 days your PR gets merged 🦕
2022-12-08 18:45:12 +01:00
1c9a3a6b25
Add Nozzle change menu to FARM mode under Settings
2022-12-05 18:22:18 +01:00
a8fe71df8c
PFW-1453 Stop Print: Don't unload if FINDA is not triggered
2022-12-05 16:45:57 +01:00
c75c81ce4f
Do not heat the bed, on load/unload
...
If during a paused print, the preheat is canceled, keep the bed target temperature
Display bed temperatures only if bed is also heated
Remove not needed variables nTargetOld and nTargetBedOld from the mFilamentItem function
Define new Setting "HeatBedOnLoad" [Yes/No]
2022-12-04 19:26:34 +02:00
3e976e04ca
Merge pull request #3777 from 3d-gussner/PFW-1431
...
PFW-1431: Add "PA Preheat"
2022-12-02 13:34:18 +01:00
54ef2a6c28
Merge pull request #3769 from 3d-gussner/MK3_Temp_model_cal_wizard
...
PFW-1434: MK3 Temp model calibration during wizard
2022-11-30 15:33:38 +01:00
0a6388cc56
Update internal translations
...
Fix G28 W
2022-11-30 15:01:24 +01:00
500131d51d
fullscreen message: use \n to force the next word on the next line
...
Useful for printing short URLs since those contain punctuation characters, which get treated at the end of a word under usual circumstances
2022-11-30 10:17:28 +01:00
8f44d1102c
Add PA preheat menu
2022-11-30 06:42:32 +01:00
23613c7eb1
optimisation: Stop print menu
...
There is no need to manually track the cursor position.
We can use the menu API:
MENU_BEGIN()
...
// menu items in between here
...
MENU_END()
Change in memory:
Flash: -116 bytes
SRAM: 0 bytes
2022-11-26 10:18:47 +00:00
83c9e946e4
Fix recursion
2022-11-24 16:15:51 +01:00
32673e1681
Nozzle change menu
2022-11-23 11:39:26 +01:00
2cd42f8433
Fix typo
...
Add Norwegian translations thanks to @OS-kar
2022-11-22 08:26:20 +01:00
aaebaf163f
Cleanup MSG_MMU_POWER_FAILS
2022-11-20 17:27:36 +01:00
4eaabbf092
Revive MMU stats + LCD screens
2022-11-20 17:27:36 +01:00
603faddd25
Fix bug where toolchange counter is not rendered
2022-11-20 15:42:29 +00:00
Yuri D'Elia
Guðni Már Gilbert
Alex Voinea
3d-gussner
Yuri D'Elia
Panayiotis-git
Jakub Dolezal
D.R.racer