188116cb7e
Preheat temperatures update
2018-01-22 16:03:43 +01:00
a94e266cf1
Documented CPU load and frequency of the following interrupts:
...
9. ISR(INT7_vect) - Fan signal interrupt
26. ISR(M_USARTx_RX_vect) - USB to serial RX
37. ISR(USART1_RX_vect) - R-PI serial RX
2018-01-20 16:20:51 +01:00
815dfcb14b
Implemented a stepper timer reset after a long blocking cli()
...
or DISABLE_STEPPER_DRIVER_INTERRUPT().
If this is not done, the stepper interrupt would likely overflow,
leading to a maximum 32ms delay before the stepper interrupt wakes up.
In addition, the stepper timer overflow error would be reported
by the debug builds.
2018-01-20 15:39:21 +01:00
17a8e2db01
Documented the interrupt blocking by a main thread by its maximum time.
...
Added a debug output to serial line on stepper timer overflow.
2018-01-20 14:58:30 +01:00
9e534c1990
Minimize risk of stepper routine interrupt blocking by reorganizing
...
the routine to move the G-code line length from the command queue
to the planner queue.
2018-01-20 14:37:22 +01:00
7edce0b890
Only show the debug menu in the DEBUG_BUILD.
2018-01-18 16:43:40 +01:00
330f1576fc
Support for debug builds:
...
A build version and repository is displayed on the welcome screen,
D-codes, stack overflow check and stepper timer overflow check
are enabled in the debug mode.
2018-01-18 16:24:25 +01:00
b5f8b1d97c
Merge pull request #412 from PavelSindler/debug_version
...
initial message for debugging fw version
2018-01-18 13:18:16 +01:00
e60cb2a79e
unload filament sequence same as in M600
2018-01-17 21:54:34 +01:00
4843f2c48e
initial message not shown on release candidate versions
2018-01-17 17:38:34 +01:00
bfa675c1a4
initial message for debugging fw version
2018-01-17 16:00:19 +01:00
b73520bcea
successfull -> successful
2018-01-17 14:40:37 +01:00
36e4e39c85
3.1.1-RC5 build 148
2018-01-16 19:25:09 +01:00
515420ce06
Merge pull request #407 from PavelSindler/MK3_for_merging
...
maiden eeprom: tmc2130_mode is set to normal
2018-01-16 17:10:38 +01:00
c2710fea63
crashdetection limits changed (X=48, Y=64)
2018-01-16 17:04:21 +01:00
fbf947b75c
maiden eeprom: tmc2130_mode is set to normal
2018-01-16 16:56:58 +01:00
6b5f9253d6
build 147
2018-01-16 16:50:05 +01:00
026f68fd6f
Merge pull request #404 from PavelSindler/xyz_fixes
...
xyz homing hotfix, xyz cal. status changed
2018-01-16 01:39:57 +01:00
9efa1d3a03
Merge pull request #403 from PavelSindler/M600_update
...
timeout fix and unload message shortened
2018-01-16 01:39:18 +01:00
f30da4bbca
babystep synchronisation
2018-01-16 01:34:44 +01:00
06c6cc119b
xyz homing hotfix, xyz cal. status changed
2018-01-16 01:00:09 +01:00
d8117eab66
timeout fix and MSG_UNLOAD_SUCCESSFULL message shortened
2018-01-15 17:39:42 +01:00
981a681e52
Temperature ISR synchronization, M600 - faster unload
2018-01-15 17:29:07 +01:00
9d52d017df
Merge pull request #401 from PavelSindler/rx_buffer
...
get command update
2018-01-15 15:28:19 +01:00
87ffb0b193
Merge pull request #400 from PavelSindler/M600_update
...
M600 update
2018-01-15 15:27:41 +01:00
aaf4e0a5e0
fixed bug - fsensor synchronization (b146)
2018-01-15 15:23:06 +01:00
1d3f6e8be5
flush rx buffer in case that it was full
2018-01-15 12:18:21 +01:00
9e7686b77f
unload changes reverted back
2018-01-15 11:35:49 +01:00
c36af887b7
M600 has timeout for nozzle, different procedure for unload
2018-01-15 11:30:28 +01:00
9aedaa8fe7
build 146
...
hard limits
fsensor overflow fix
2018-01-14 23:59:43 +01:00
3201fd1538
removed duplicit comment
2018-01-14 19:36:30 +01:00
552b1f03b1
build 145
...
fixed - finishstatus declaration
2018-01-13 19:16:09 +01:00
78d6088d48
Merge pull request #392 from PavelSindler/fail_stats
...
filament fails counter fix
2018-01-12 22:23:18 +01:00
8bd84ba4fd
Merge pull request #396 from XPila/MK3
...
Mk3
2018-01-12 22:08:50 +01:00
5ed9233abc
Missed a bit with the last commit.
2018-01-12 22:01:53 +01:00
530dfba417
Status message limit (PFW-124)
2018-01-12 21:21:21 +01:00
82304a2268
Slight optimization of the fan speed interrupt routine by accessing
...
the Arduino millis() without locking interrupts.
2018-01-12 21:16:29 +01:00
ebf6d08fae
Crash detection - message on lcd (PFW-115)
2018-01-12 21:02:49 +01:00
135dda1bff
Slight optimization of the stepper timer routine.
...
Use WRITE_NC instead of WRITE for writing into the slow ports.
2018-01-12 21:01:01 +01:00
3e6d853364
Debugging of the stepper timer routine. When enabled through
...
DEBUG_STEPPER_TIMER_MISSED, the printer is halted on stepper timer overflow
and an error message is displayed.
2018-01-12 20:51:14 +01:00
23b78da2f5
filament fails counter fixed
2018-01-12 20:21:07 +01:00
26747d7236
Definition of 8 pins on the Einsy 0.4 board connected to pin headers
...
to be monitored by an 8 channel logic analyzer, for example the Saleae.
2018-01-12 20:18:20 +01:00
db985065ff
WRITE_NC macro for non-critical (non-synchronized) access to
...
slow ports. The WRITE macro stores the CPU bits on the stack first,
then locks the interupts, reads the port, sets a bit, writes the port
and then finally reverts the CPU bits. The WRITE_NC does not lock
the interrupts, therefore it may only be used where it cannot
be interrupted.
2018-01-12 20:15:59 +01:00
1fbed53200
initial
2018-01-12 20:01:22 +01:00
0f46fa0c37
blocking messages in settings/tune menu (PFW104)
...
switch normal/stealth (PFW110)
2018-01-12 19:54:32 +01:00
a4be2af538
commit nr updated
2018-01-11 17:51:30 +01:00
f5ed12817d
Merge pull request #388 from PavelSindler/first_layer_saving
...
Live adjust Z saving using timeout
2018-01-11 17:49:40 +01:00
5c1db284b0
remove setting live adjust status in setup function
2018-01-11 17:48:58 +01:00
97bd56d560
Merge pull request #386 from PavelSindler/selftest_swapped_fans
...
manual check for swapped fans
2018-01-11 17:45:23 +01:00
cfae8f859d
Merge branch 'MK3' into fw_versions
2018-01-11 16:58:47 +01:00
087532085f
development fw versions has initial message for warning
2018-01-11 15:50:26 +01:00
cc20da62a8
whitespace
2018-01-10 23:31:06 +01:00
c185b46eb2
live adjust Z saving using timeout
2018-01-10 23:28:41 +01:00
0d269261e4
PFW-110 - load filament - beep when loading finished.
2018-01-10 18:50:16 +01:00
c79d960cb5
manual check for swapped fans
2018-01-10 16:40:06 +01:00
6ff7641d97
Merge pull request #385 from XPila/MK3
...
Build 143f
2018-01-09 20:01:56 +01:00
43010b30b4
Build 143f
...
Crashdetection improoved, blocking temperature ISR fixed, limits for silent mode adjusted.
2018-01-09 19:54:07 +01:00
858945d949
thermal runaway: reset cmd queue to ensure that heater/bed temp will be always set to zero
2018-01-09 13:35:12 +01:00
75efc71527
temp runaway for heatbed enabled in config
2018-01-08 16:15:50 +01:00
b53197fdd1
Fixed error messages for print fan and extruder fan (were swapped)
2018-01-08 12:07:45 +01:00
0a2087c1cb
build 143e
...
Linear advance disabled
Max feedrate reduced to 200mm/s
Silent max accel reduced to 984mm/s^2
some debug logs removed, tmc_init - log message fixed
2018-01-04 18:08:22 +01:00
8a5ba89a9c
Missing serial characters debuging
...
disabled fan ISR
disabled fsensor ISR
disabled linear advance
build 143b
2018-01-02 20:55:33 +01:00
c6e77f55f6
checkrx in stepper returned back
...
build 143a
2017-12-30 02:55:22 +01:00
568f03c46e
build 143
2017-12-29 23:49:11 +01:00
8d1f2afbf2
build number change
...
just 141r -> 142
2017-12-29 20:22:45 +01:00
0920b62d80
build number change
2017-12-29 20:21:06 +01:00
734639c1da
Unload filament tweak
...
unload filament now has longer and faster slow retract.
2017-12-29 17:53:12 +01:00
7fb1234855
Turn off bed heater after temp calibration
...
After finishing the temperature calibration, turn off the bed heater
right away, before waiting for the user to acknowledge completion.
2017-12-28 23:47:27 -08:00
e3c006dbe9
Serial communication uses port0 or port1, not both, removed some suspected code.
...
build 141
2017-12-29 00:06:47 +01:00
f71f133e80
power panic polished
...
Retraction set correctly to have minimum missing line
Z motor current not lowered that drascialy
Extruder motor turning off instantly
Beeping added to the end
2017-12-28 23:26:06 +01:00
f1c741d027
Filament autoloading improved and minor tweaks
...
Filament autoloading now acts like normal loading (Error message pops out if nozzle too cold, Printer asks if should extrude more when done loading)
Autoloading now unable to turn on when filament sensor is turned off or not responding
Color not right changed to color not correct to avoid slight confusion
2017-12-28 18:59:57 +01:00
26255766f6
Translation fix
...
on -> zap
off -> vyp
2017-12-28 15:55:16 +01:00
5e5588c72c
Text grooming
...
Added language mutations of error messages, menu items.
Synced wording of crash detection in messages.
rPi port -> RPi port.
Minor menu items alignment.
2017-12-28 15:45:52 +01:00
bd58718d9d
dummy "ok" response
...
build 139 (RC4)
2017-12-28 02:45:05 +01:00
e064133a04
Merge remote-tracking branch 'upstream/MK3' into MK3
...
# Please enter a commit message to explain why this merge is necessary,
# especially if it merges an updated upstream into a topic branch.
#
# Lines starting with '#' will be ignored, and an empty message aborts
# the commit.
2017-12-28 01:37:13 +01:00
69d496e157
autoload filament menu (PFW-95, PFW-96)
2017-12-27 21:57:51 +01:00
cbd7f033e8
crashdetection and mode menu (PFW-85, PFW-97)
2017-12-27 21:43:04 +01:00
546314fda7
Removed debug messages from serial comunication (octoprint...).
...
build 137b
2017-12-27 20:29:24 +01:00
f9d5619682
MINTEMP safety for ambient temperature < 18C
...
Silent mode acceleration limit lowered to 1000mm/s^2
2017-12-27 18:20:04 +01:00
a09dee7aea
build 138 (RC3)
2017-12-23 03:44:47 +01:00
23ed33fc21
disable crashdetection while usb printing
2017-12-23 03:42:19 +01:00
8739b4a610
MINTEMP fix
2017-12-23 03:36:08 +01:00
1a69c979bf
Increase Z current (PFW-90).
2017-12-23 01:01:57 +01:00
8f7a50cfcd
Merge pull request #343 from PavelSindler/m110_fix
...
M110 fix
2017-12-23 00:04:11 +01:00
e8477b525c
initial version of M110 fix (port from MK2)
2017-12-22 22:34:57 +01:00
257b8e9f59
Merge pull request #342 from XPila/MK3
...
Mk3 - RC3
2017-12-22 20:35:15 +01:00
c4b045083c
Extrude mintemp increased to 190C
2017-12-22 20:34:24 +01:00
7f05b9fd44
changed menu order (PFW 91)
2017-12-22 20:31:45 +01:00
6abba7bfe9
filament autoload - better detection algorithm, autoload in M600 from menu
...
unload menu always visible
2017-12-22 20:14:26 +01:00
7114772784
whitespace
2017-12-22 19:23:11 +01:00
3aca1271ed
serial resend request always contains OK
2017-12-22 18:54:55 +01:00
6f7a2ba263
Merge pull request #340 from PavelSindler/MK3_for_merging
...
removed some serial line error messages
2017-12-22 13:35:33 +01:00
1917b6a1d7
removed some serial line error messages which caused that octoprint changed status
2017-12-22 13:27:04 +01:00
33d715616f
Merge pull request #339 from PavelSindler/MK3_for_merging
...
setup function
2017-12-21 13:42:22 +01:00
71bb4022dc
setup function
2017-12-21 13:40:16 +01:00
3ddbac6056
LCD_PWM removed (will be solved other way)
2017-12-21 01:00:49 +01:00
f227952c0b
Merge branch 'MK3' into MK3
2017-12-21 00:07:01 +01:00
b8fd058749
selftest fix
2017-12-21 00:03:41 +01:00
17d9bb205a
selftest tests filament sensor, selftest messages have language variants
2017-12-20 23:40:18 +01:00
eba2924fdd
Remove load/unload menu when autoload enabled
2017-12-20 22:55:11 +01:00
PavelSindler
bubnikv
PavelSindler
Robert Pelnar
Michal Průša
Phil Dubach