An example is when Unloading filament with MMU.
After the unload completes successfully, some menu items disappeared.
Because mFilamentBack() was not called
Change in memory:
Flash: -56 bytes
SRAM: 0 bytes
Kudos to @3d-gussner for finding the issue
Steps to reproduce:
1. reset printer
2. select Load filament
3. go back to main
4. LCD menu is very limited
5. To get all menus back select 6. Preheat
7. back to main
This commit is my proposed fix.
When eFilamentAction is equal to
FilamentAction::Load we must reset it to FilamentAction::None
when the Back button in Load Filament is selected
Change in memory:
Flash: -26 bytes
SRAM: 0 bytes
Proposal to fix some of the issues with the initial implementation
it is safer to use the status line code to print the message so
there aren't any conflicts in the LCD cursor position.
Allow inserting a byte into any position in the LCD status message
Also, add a variable to control from which index in the array
should the message start printing. This is very useful for progress
bars and messages which continually update. I think we can save some
memory by applying this to Mesh Bed Leveling later.
Change in memory:
Flash: +106 bytes
SRAM: +1 byte
Remove loading_flag and check for eFilamentAction instead which already
flags both load/unload (in addition to mmu actions).
Correctly transition from AutoLoad to Load as soon as the operation
cannot be cancelled anymore as opposed to resetting it.
Do not blidnly clear the loading_flag, check for it!
Just disallowing the SD menu while loading is being performed is not
sufficient, since the menu can be entered also by inserting card while
loading is taking place.
This is also nicer in behavior, as we allow to navigate the SD card
while loading.
All custom commands are transitory and eventually switch back to Idle
state by themselves.
It doesn't make any sense to explicitly check for Layer1Cal: any
non-idle state is active by design.
Fix this check in the main menu. This is probably incomplete (Layer1Cal
is incorrectly used in several other places).
This is by far the simplest solution to prevent the user from sending
a Load command to the MMU when the FINDA or Filament sensor
is detecting a filament. This may even happen if the sensors are poorly positioned.
Either way a Load in this scenario will make the MMU seem to hang as the
state machine will reject the command.
We could add a full screen message to let the use know
but it would require some memory resources.
For now, just hide the menu item.
Change in memory:
Flash: +16 bytes
SRAM: 0 bytes
bFilamentAction variable is never reset, even after
disabling the heaters.
Steps to reproduce:
1. Boot-up printer
2. Select Load to Nozzle.
3. Select PLA (215°C) target
4. Select Filament 1
5. Wait for load to be successful
6. Go to Preheat submenu and select Cooldown (last menu item)
7. Observe target temperature on the status screen is now 0°C
8. Select Load to Nozzle again.
9. Select Filament 2.
* Expected behavior target temperature IS NOT 0°C
* Actual behavior target temperature IS 0°C
Change in memory:
Flash: -26 bytes
SRAM: 0 bytes
Restores 3.12 sequence which was working well before.
M600 "L" parameter now works like M702 "U" parameter.
Removed a lot of the unused parameters which were copied
from Marlin 2.
Change in memory:
Flash: +96 bytes
Code size increases a bit but keep in mind the PR
that broke the behavior "saved" 182 bytes:
https://github.com/prusa3d/Prusa-Firmware/pull/4063
So I think this code size increase is OK
Change in memory:
Flash: +84 bytes
SRAM: 0 bytes
If the remaining print time is more than 10.9 hours at 100%
then increasing the feedrate multiplier
to 101% or more will yield an unrealistic time due to overflow occuring.
Change in memory:
Flash +2 bytes
SRAM: 0 bytes
Guard the feedmultiply code with
lcd_encoder.
if lcd_encoder = 0, then there is no need to check if
feedmultiply should be updated.
Also set lcd_encoder to zero in one line to consume the rotation event.
Change in memory:
Flash: -40 bytes
SRAM: 0 bytes
Guard the lcd_display_message_fullscreen_P call by blocks_queued(). If there are no planned moves, there is no need to render this message, it creates a weird LCD draw noticable by the user.
Change in memory:
Flash: +10 bytes
SRAM: 0 bytes
Drop the sound feedback in lcd_v2_calibration
when switching to lcd_generic_preheat_menu
If a single filament setup (no MMU) has filament loaded, it will jump
immediately to lcd_generic_preheat_menu
this created double feedback.
Let's just drop the feedback since the transition
between menus is very fast.
Change in memory:
Flash: -8 bytes
For MMU users: This happens when the user
selects a filament to load from 1 to 5
For non-MMU: this happens when clicking
the knob within 2 seconds.
Additionally fixed the code indendation
it was a mix of spaces and tabs
Changes in
lcd_implementation_drawmenu_sdfile
and
lcd_implementation_drawmenu_sddirectory
seem to save the most.
Change in memory:
Flash: -72 bytes
SRAM: 0 bytes
There are only 3 possible values. No need to check for two of them
to rule of the last value. Instead simply check for the last value only.
Change in memory:
Flash: -16 bytes
SRAM: 0 bytes
Guðni Már Gilbert
VintagePC
3d-gussner
Yuri D'Elia
Guðni Már Gilbert
Alex Voinea