ARM: add a board configuration for Gen7-ARM.
Wohoo, this is the first ARM board in Configtool. Let's see how Configtool deals with it :-)
This commit is contained in:
Markus Hitter
parent
2dd35e6529
commit
5a8dcf8e97
|
|
@ -0,0 +1,257 @@
|
||||||
|
|
||||||
|
/***************************************************************************\
|
||||||
|
* *
|
||||||
|
* 1. CPU *
|
||||||
|
* *
|
||||||
|
\***************************************************************************/
|
||||||
|
|
||||||
|
/** \def CPU_TYPE
|
||||||
|
CPU types a user should be able to choose from in configtool. All
|
||||||
|
commented out.
|
||||||
|
*/
|
||||||
|
//#define CPU_TYPE lpc1114
|
||||||
|
|
||||||
|
/** \def CPU
|
||||||
|
CPU actually present on the board.
|
||||||
|
*/
|
||||||
|
#define CPU lpc1114
|
||||||
|
|
||||||
|
/** \def F_CPU_OPT
|
||||||
|
CPU clock frequencies a user should be able to choose from in configtool.
|
||||||
|
All commented out.
|
||||||
|
*/
|
||||||
|
//#define F_CPU_OPT 12000000UL
|
||||||
|
|
||||||
|
/** \def F_CPU
|
||||||
|
Actual CPU clock rate. #ifndef required for Arduino compatibility.
|
||||||
|
*/
|
||||||
|
#ifndef F_CPU
|
||||||
|
#define F_CPU 12000000UL
|
||||||
|
#endif
|
||||||
|
|
||||||
|
/** \def MOTHERBOARD
|
||||||
|
This is the motherboard, as opposed to the extruder. See extruder/ directory
|
||||||
|
for GEN3 extruder firmware.
|
||||||
|
*/
|
||||||
|
#define MOTHERBOARD
|
||||||
|
|
||||||
|
|
||||||
|
/***************************************************************************\
|
||||||
|
* *
|
||||||
|
* 2. PINOUTS *
|
||||||
|
* *
|
||||||
|
\***************************************************************************/
|
||||||
|
|
||||||
|
//#define TX_ENABLE_PIN xxxx
|
||||||
|
//#define RX_ENABLE_PIN xxxx
|
||||||
|
|
||||||
|
#define X_STEP_PIN PIO1_5
|
||||||
|
#define X_DIR_PIN PIO1_4
|
||||||
|
#define X_MIN_PIN PIO1_8
|
||||||
|
//#define X_MAX_PIN PIO1_8
|
||||||
|
//#define X_ENABLE_PIN xxxx
|
||||||
|
//#define X_INVERT_DIR
|
||||||
|
//#define X_INVERT_MIN
|
||||||
|
//#define X_INVERT_MAX
|
||||||
|
//#define X_INVERT_ENABLE
|
||||||
|
|
||||||
|
#define Y_STEP_PIN PIO1_3
|
||||||
|
#define Y_DIR_PIN PIO1_2
|
||||||
|
#define Y_MIN_PIN PIO1_8
|
||||||
|
//#define Y_MAX_PIN PIO1_8
|
||||||
|
//#define Y_ENABLE_PIN xxxx
|
||||||
|
//#define Y_INVERT_DIR
|
||||||
|
//#define Y_INVERT_MIN
|
||||||
|
//#define Y_INVERT_MAX
|
||||||
|
//#define Y_INVERT_ENABLE
|
||||||
|
|
||||||
|
#define Z_STEP_PIN PIO0_1
|
||||||
|
#define Z_DIR_PIN PIO0_2
|
||||||
|
#define Z_MIN_PIN PIO1_8
|
||||||
|
//#define Z_MAX_PIN PIO1_8
|
||||||
|
//#define Z_ENABLE_PIN xxxx
|
||||||
|
//#define Z_INVERT_DIR
|
||||||
|
//#define Z_INVERT_MIN
|
||||||
|
//#define Z_INVERT_MAX
|
||||||
|
//#define Z_INVERT_ENABLE
|
||||||
|
|
||||||
|
#define E_STEP_PIN PIO0_4
|
||||||
|
#define E_DIR_PIN PIO0_7
|
||||||
|
//#define E_ENABLE_PIN xxxx
|
||||||
|
//#define E_INVERT_DIR
|
||||||
|
//#define E_INVERT_ENABLE
|
||||||
|
|
||||||
|
#define PS_ON_PIN PIO0_3
|
||||||
|
//#define PS_MOSFET_PIN xxxx
|
||||||
|
#define STEPPER_ENABLE_PIN PIO0_3
|
||||||
|
#define STEPPER_INVERT_ENABLE
|
||||||
|
|
||||||
|
/** \def DEBUG_LED_PIN
|
||||||
|
|
||||||
|
Enable flashing of a LED during motor stepping.
|
||||||
|
|
||||||
|
Disabled by default. Uncommenting this makes the binary a few bytes larger
|
||||||
|
and adds a few cycles to the step timing interrrupt in timer.c. Also used
|
||||||
|
for precision profiling (profiling works even without actually having such
|
||||||
|
a LED in hardware), see
|
||||||
|
http://reprap.org/wiki/Teacup_Firmware#Doing_precision_profiling
|
||||||
|
*/
|
||||||
|
//#define DEBUG_LED_PIN xxxx
|
||||||
|
|
||||||
|
/** \def SD_CARD_SELECT_PIN
|
||||||
|
|
||||||
|
Chip Select pin of the SD card.
|
||||||
|
|
||||||
|
SD cards work over SPI and have a Chip Select or Slave Select (SS) pin.
|
||||||
|
Choose this pin according to where on the board your SD card adapter is
|
||||||
|
connected. Disabling this pin also disables SD card support and makes the
|
||||||
|
firmware binary about 4.5 kB smaller.
|
||||||
|
|
||||||
|
Connecting a device to SPI actually uses 4 signal lines, the other three
|
||||||
|
pins are choosen by Teacup automatically.
|
||||||
|
*/
|
||||||
|
//#define SD_CARD_SELECT_PIN xxxx
|
||||||
|
|
||||||
|
|
||||||
|
/***************************************************************************\
|
||||||
|
* *
|
||||||
|
* 3. TEMPERATURE SENSORS *
|
||||||
|
* *
|
||||||
|
\***************************************************************************/
|
||||||
|
|
||||||
|
#ifndef DEFINE_TEMP_SENSOR
|
||||||
|
#define DEFINE_TEMP_SENSOR(...)
|
||||||
|
#endif
|
||||||
|
|
||||||
|
/** \def TEMP_MAX6675 TEMP_THERMISTOR TEMP_AD595 TEMP_PT100 TEMP_INTERCOM
|
||||||
|
Which temperature sensor types are you using? Leave all used ones
|
||||||
|
uncommented, comment out all others to save binary size and enhance
|
||||||
|
performance.
|
||||||
|
*/
|
||||||
|
//#define TEMP_MAX6675
|
||||||
|
#define TEMP_THERMISTOR
|
||||||
|
//#define TEMP_AD595
|
||||||
|
//#define TEMP_PT100
|
||||||
|
//#define TEMP_INTERCOM
|
||||||
|
|
||||||
|
/** \def TEMP_SENSOR_PIN
|
||||||
|
Temperature sensor pins a user should be able to choose from in configtool.
|
||||||
|
All commented out.
|
||||||
|
*/
|
||||||
|
//#define TEMP_SENSOR_PIN PIO1_0
|
||||||
|
//#define TEMP_SENSOR_PIN PIO1_1
|
||||||
|
|
||||||
|
/** \def DEFINE_TEMP_SENSOR
|
||||||
|
Define your temperature sensors here. One line for each sensor, only
|
||||||
|
limited by the number of available ATmega pins.
|
||||||
|
|
||||||
|
Name must match the name of the corresponding heater. If a heater "extruder"
|
||||||
|
exists, a temperature sensor of that name has to exist as well. Same for
|
||||||
|
heater "bed". There can be one sensor without corresponding heater, name it
|
||||||
|
"noheater".
|
||||||
|
|
||||||
|
Types are same as TEMP_ list above - TT_MAX6675, TT_THERMISTOR, TT_AD595,
|
||||||
|
TT_PT100, TT_INTERCOM. See list in temp.c.
|
||||||
|
|
||||||
|
The "additional" field is used for TT_THERMISTOR only. It defines the
|
||||||
|
name of the table(s) in thermistortable.h to use. This name is arbitrary,
|
||||||
|
often used names include THERMISTOR_EXTRUDER and THERMISTOR_BED. Also,
|
||||||
|
several sensors can share the same table, which saves binary size.
|
||||||
|
|
||||||
|
For a GEN3 set temp_type to TT_INTERCOM and temp_pin to AIO0. The pin
|
||||||
|
won't be used in this case.
|
||||||
|
*/
|
||||||
|
//DEFINE_TEMP_SENSORS_START
|
||||||
|
// name type pin additional
|
||||||
|
DEFINE_TEMP_SENSOR(extruder, TT_THERMISTOR, PIO1_1,THERMISTOR_EXTRUDER)
|
||||||
|
DEFINE_TEMP_SENSOR(bed, TT_THERMISTOR, PIO1_0,THERMISTOR_BED)
|
||||||
|
|
||||||
|
// Beta algorithm r0 beta r2 vadc
|
||||||
|
// Steinhart-Hart rp t0 r0 t1 r1 t2 r2
|
||||||
|
//TEMP_TABLE EXTRUDER (100000, 4092, 4700, 5.0)
|
||||||
|
//TEMP_TABLE BED (100000, 4092, 4700, 5.0)
|
||||||
|
//DEFINE_TEMP_SENSORS_END
|
||||||
|
|
||||||
|
|
||||||
|
/***************************************************************************\
|
||||||
|
* *
|
||||||
|
* 4. HEATERS *
|
||||||
|
* *
|
||||||
|
\***************************************************************************/
|
||||||
|
|
||||||
|
#ifndef DEFINE_HEATER
|
||||||
|
#define DEFINE_HEATER(...)
|
||||||
|
#endif
|
||||||
|
|
||||||
|
/** \def HEATER_PIN
|
||||||
|
Heater pins a user should be able to choose from in configtool. All
|
||||||
|
commented out.
|
||||||
|
*/
|
||||||
|
//#define HEATER_PIN PIO0_10
|
||||||
|
//#define HEATER_PIN PIO0_11
|
||||||
|
|
||||||
|
/** \def DEFINE_HEATER
|
||||||
|
Define your heaters and devices here.
|
||||||
|
|
||||||
|
To attach a heater to a temp sensor above, simply use exactly the same
|
||||||
|
name - copy+paste is your friend. Some common names are 'extruder',
|
||||||
|
'bed', 'fan', 'motor', ... names with special meaning can be found
|
||||||
|
in gcode_process.c. Currently, these are:
|
||||||
|
HEATER_extruder (M104)
|
||||||
|
HEATER_bed (M140)
|
||||||
|
HEATER_fan (M106)
|
||||||
|
|
||||||
|
Devices don't neccessarily have a temperature sensor, e.g. fans or
|
||||||
|
milling spindles. Operate such devices by setting their power (M106),
|
||||||
|
instead of setting their temperature (M104).
|
||||||
|
|
||||||
|
Also note, the index of a heater (M106 P#) can differ from the index of
|
||||||
|
its attached temperature sensor (M104 P#) in case sensor-less devices
|
||||||
|
are defined or the order of the definitions differs. The first defined
|
||||||
|
device has the index 0 (zero).
|
||||||
|
|
||||||
|
Set 'pwm' to ...
|
||||||
|
1 for using PWM on a PWM-able pin and on/off on other pins.
|
||||||
|
0 for using on/off on a PWM-able pin, too.
|
||||||
|
|
||||||
|
Using PWM usually gives smoother temperature control but can conflict
|
||||||
|
with slow switches, like solid state relays. PWM frequency can be
|
||||||
|
influenced globally with FAST_PWM, see below.
|
||||||
|
*/
|
||||||
|
//DEFINE_HEATERS_START
|
||||||
|
// name port pwm
|
||||||
|
DEFINE_HEATER(extruder, PIO0_11, 1)
|
||||||
|
DEFINE_HEATER(bed, PIO0_10, 1)
|
||||||
|
|
||||||
|
#define HEATER_EXTRUDER HEATER_extruder
|
||||||
|
#define HEATER_BED HEATER_bed
|
||||||
|
//DEFINE_HEATERS_END
|
||||||
|
|
||||||
|
|
||||||
|
/***************************************************************************\
|
||||||
|
* *
|
||||||
|
* 5. COMMUNICATION OPTIONS *
|
||||||
|
* *
|
||||||
|
\***************************************************************************/
|
||||||
|
|
||||||
|
/** \def BAUD
|
||||||
|
Baud rate for the serial RS232 protocol connection to the host. Usually
|
||||||
|
115200, other common values are 19200, 38400 or 57600. Ignored when USB_SERIAL
|
||||||
|
is defined.
|
||||||
|
*/
|
||||||
|
#define BAUD 115200
|
||||||
|
|
||||||
|
/** \def XONXOFF
|
||||||
|
Xon/Xoff flow control.
|
||||||
|
|
||||||
|
Redundant when using RepRap Host for sending G-code, but mandatory when
|
||||||
|
sending G-code files with a plain terminal emulator, like GtkTerm (Linux),
|
||||||
|
CoolTerm (Mac) or HyperTerminal (Windows).
|
||||||
|
*/
|
||||||
|
//#define XONXOFF
|
||||||
|
|
||||||
|
/** \def USB_SERIAL
|
||||||
|
Define this for using USB instead of the serial RS232 protocol. Works on
|
||||||
|
USB-equipped ATmegas, like the ATmega32U4, only.
|
||||||
|
*/
|
||||||
|
//#define USB_SERIAL
|
||||||
|
|
@ -3,6 +3,7 @@ protectedFiles = [
|
||||||
"board.3drag.h",
|
"board.3drag.h",
|
||||||
"board.gen3.h",
|
"board.gen3.h",
|
||||||
"board.gen6.h",
|
"board.gen6.h",
|
||||||
|
"board.gen7-arm.h",
|
||||||
"board.gen7-v1.1-v1.3.h",
|
"board.gen7-v1.1-v1.3.h",
|
||||||
"board.gen7-v1.4.h",
|
"board.gen7-v1.4.h",
|
||||||
"board.nanoheart-v1.0.h",
|
"board.nanoheart-v1.0.h",
|
||||||
|
|
|
||||||
3
mendel.c
3
mendel.c
|
|
@ -28,10 +28,7 @@
|
||||||
#include <avr/interrupt.h>
|
#include <avr/interrupt.h>
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#ifndef __ARMEL_NOTYET__
|
|
||||||
#include "config_wrapper.h"
|
#include "config_wrapper.h"
|
||||||
#endif /* __ARMEL_NOTYET__ */
|
|
||||||
|
|
||||||
#include "cpu.h"
|
#include "cpu.h"
|
||||||
#include "serial.h"
|
#include "serial.h"
|
||||||
#ifndef __ARMEL_NOTYET__
|
#ifndef __ARMEL_NOTYET__
|
||||||
|
|
|
||||||
Loading…
Reference in New Issue