This code was accidentally removed long ago in a botched merge. This
patch recovers it and makes it build again. I've done minimal testing
and some necessary cleanup. It compiles and runs, but it probably still
has a few dust bunnies here and there.
I added registers and pin definitions to simulator.h and
simulator/simulator.c which I needed to match my Gen7-based config.
Other configs or non-AVR ports will need to define more or different
registers. Some registers are 16-bits, some are 8-bit, and some are just
constant values (enums). A more clever solution would read in the
chip-specific header and produce saner definitions which covered all
GPIOs. But this commit just takes the quick and easy path to support my
own hardware.
Most of this code originated in these commits:
commit cbf41dd4ad
Author: Stephan Walter <stephan@walter.name>
Date: Mon Oct 18 20:28:08 2010 +0200
document simulation
commit 3028b297f3
Author: Stephan Walter <stephan@walter.name>
Date: Mon Oct 18 20:15:59 2010 +0200
Add simulation code: use "make sim"
Additional tweaks:
Revert va_args processing for AVR, but keep 'int' generalization
for simulation. gcc wasn't lying. The sim really aborts without this.
Remove delay(us) from simulator (obsolete).
Improve the README.sim to demonstrate working pronterface connection
to sim. Also fix the build instructions.
Appease all stock configs.
Stub out intercom and shush usb_serial when building simulator.
Pretend to be all chip-types for config appeasement.
Replace sim_timer with AVR-simulator timer:
The original sim_timer and sim_clock provided direct replacements
for timer/clock.c in the main code. But when the main code changed,
simcode did not. The main clock.c was dropped and merged into timer.c.
Also, the timer.c now has movement calculation code in it in some
cases (ACCELERATION_TEMPORAL) and it would be wrong to teach the
simulator to do the same thing. Instead, teach the simulator to
emulate the AVR Timer1 functionality, reacting to values written to
OCR1A and OCR1B timer comparison registers.
Whenever OCR1A/B are changed, the sim_setTimer function needs to be
called. It is called automatically after a timer event, so changes
within the timer ISRs do not need to bother with this.
A C++ class could make this requirement go away by noticing the
assignment. On the other hand, a chip-agnostic timer.c would help
make the main code more portable. The latter cleanup is probably
better for us in the long run.
The binary size impact is moderate, like 18 bytes plus
4 bytes per endstop defined.
The story is a follows:
The endstop logic can be used to use a touch probe with PCB
milling. Connect the (conductive) PCB surface to GND, the
spindle/mill bit to the signal line, turn the internal pullups
on and there you go.
However, doing so with pullups always enabled and while milling
under (conductive) water showed polished mill and drill bits to
become matte after a few hours of usage. Obviously, this small
0.5 mA current from the pullup resistors going through the
rotating mill bit is sufficient to get some spark erosion going.
That's bad, as spark erosion happening also means tools become
dull faster than neccessary.
With this patch, pullups are turned on while being used, only,
so this sparc erosion should go away.
This enhances encapsulation.
An attempt to initialise only the timers in use was abandoned.
This isn't only unneccessary, as pins are still in normal
operation mode unless their bits in TCCR0A/TCCR2A/... are set,
even with the timer behind the pins running, it's also at least
tricky to sort pins and their timer bits at compile time. Doing
the sorting at runtime would cause additional binary size.
- ATmega32U timer 4 register handling differs from other AVRs:
Change heater.c and mendel.c.
- LUFA USB recognition expanded in Makefile.
- Add section for __AVR_ATmega32U4__ in arduino.h.
Instead of converting them to absolute first, then back to
relative and having all the fuzz with working on the queue's
start vs. working at the queue's end, mark a movement as relative
and use this directly.
This includes:
- Initialize them in mendel.c.
- While running, switch the pin only.
- Sort mendel.c the same order as in pinio.h.
- Remove the requirement of a parameter for this flag, like
it's with all other flags.
This required to also introduce dda_init() and re-adjust the
number of accelerating steps a bit.
Goal of this is to make look-ahead possible by just reducing
the number of deceleration steps and acceleration steps of
the next move. dda->c and dda->n no longer go down to their
initial values, then.
Also, quite a number of variables in the dda struct are used only when
the dda is live, so there is no need to store that for each
movement of the queue.
This costs 2 bytes of ram, but saves 60 bytes of flash. Doing so
also eliminates the need to disable interrupts while clearing flags
in the ifclock macro.
Conflicts:
clock.c
timer.c
timer.h
All other firmwares set them to zero -> no internal pullup resistor,
as they counter-work to the design of the electronic endstops.
However, in conjunction with mechanical endstops, they're very practical.
Phil Hord
Markus Hitter
David Forrest
Jim McGee
Michael Moon
Ben Jackson
Stephan Walter
Markus Amsler