be81a13584
make sure timer is initialised properly
...
Reported-by: jv4779 <jv4779@gmail.com>
2011-04-30 11:00:11 +10:00
143398705c
add "functionsbysize" make target
2011-04-29 10:55:42 +10:00
e2cb6aef72
M109 just waits if no temperature provided
2011-04-29 10:15:49 +10:00
61ca4c114e
fixed temperature reading problem where ReplicatorG would freeze because there is no newline before the temperature prints out...
2011-04-29 10:15:40 +10:00
74e03b7df1
allow G92 to work again after 0389289
2011-04-26 18:19:00 +10:00
03892894ed
remove ACCELERATION_TEMPORAL, update current_position from main loop instead of step interrupt
2011-04-26 14:45:32 +10:00
e108ab2548
M114 returns millimeters instead of steps
2011-04-26 14:44:17 +10:00
ee481864fa
gcode_parse.c: get rid of the denominator variable in decfloat_to_int().
...
This allows for better optimisation and saves 100 bytes binary size
accordingly. For denominator = 1, the algorithm is also significantly
simpler.
2011-04-15 02:12:13 +02:00
6896aa5236
gcode_parse.c: join the upper and the lower formula in decfloat_to_int().
...
This also makes rounding more accurate with exponent > 0.
Saves another 40 bytes binary size.
2011-04-15 02:12:10 +02:00
8cf8a8a44a
gcode_parse.c: get rid of rounding[].
...
This saves 8 bytes of flash and, more important, 16 bytes of RAM.
2011-04-15 02:12:07 +02:00
f41dd9c098
gcode_parse.c: make all usages of decfloat_to_int()...
...
... to divide either by 1 or 1000. Accordingly, a flag
can be used instead of the actual value, shrinking code
size by 70 bytes.
2011-04-15 02:12:02 +02:00
26b9a7df54
extruder: Add dummy temp sensor so analog_mask includes trim pot.
2011-04-12 20:38:28 +02:00
15f835320f
Update config.gen3.h to support a heated bed over intercom.
2011-04-12 20:12:20 +02:00
e937b052af
Add support for multiple thermistor tables.
...
DEFINE_TEMP_SENSOR takes one additional argument. For TT_THERMISOR you can specify there which thermistor table to use.
2011-04-12 20:00:18 +02:00
8856dd9908
Only print queue on every G command if DEBUG_POSITION is set.
2011-04-12 01:37:11 +02:00
4b7f8fba48
Fix absolute E positioning.
...
Now also works with M101/M103
2011-04-12 01:36:57 +02:00
1d556e0278
Use HEATER_BED everywhere.
...
For intercom heated bed it may be different from HEATER_bed.
2011-04-11 22:41:50 +02:00
c54c964fc0
initialise heaters on timers 3/4/5
2011-04-11 11:22:09 +10:00
15ed65dbad
No SEARCH_FEEDRATE_E, as E can't be searched.
2011-04-10 15:56:07 +02:00
ae33cb7fa2
start implementing absolute E support
2011-04-09 09:16:05 +10:00
b37a5d435e
home Z to max if possible by default
2011-04-09 09:15:48 +10:00
f4e4788892
wait for queue to empty before homing
2011-04-09 09:15:22 +10:00
d97a4519d3
extruder: Get rid of _CONFIG_H, like on the mainboard config.
2011-04-07 03:29:17 +02:00
ad7f7f0e96
Don't set all axis to home on G92 E0
2011-04-07 03:15:47 +02:00
0a92c13051
extruder: sync heater.c
2011-04-05 02:14:34 +02:00
57a75ecbfb
temp: TEMP_RESIDENCY_TIME is in seconds not in temp_ticks (=10ms)
2011-04-04 09:21:32 +10:00
95e7cda9db
avoid warning: 'SpecialMoveE' defined but not used
2011-04-04 09:16:52 +10:00
be18eb90b8
Convert TEMP_HYSTERESIS to Celsius.
2011-04-04 09:12:54 +10:00
093d20481e
heater: fix residency compare.
...
labs requires a signed int.
2011-04-04 09:12:54 +10:00
9860d2850f
heater: only reset residency if temp really changed
...
Skeinforge generates sometimes multiple calls to M104/M140, which would add a slow delay on the next M101.
2011-04-04 09:12:53 +10:00
3a271ee487
intercom: make sure extruder switches to listen mode
2011-04-04 09:12:53 +10:00
5656c5050c
Implement M116 - Wait
2011-04-04 09:12:53 +10:00
dba60ba1eb
fix error: lvalue required as unary '&' operand when heater pin is not a PWMable pin.
2011-04-04 09:10:25 +10:00
a35c304762
add encoding to createTemperatureLookup.py
...
Signed-off-by: Michael Moon <triffid.hunter@gmail.com>
2011-03-30 12:18:42 +11:00
66415078e5
update extruder to match simplified heater
2011-03-28 21:54:58 +11:00
3c3624542f
simplify heater configuration by using arduino_*.h more effectively with DEFINE_HEATER macro
2011-03-28 18:45:28 +11:00
100b7c6c4a
only check intercom every 250ms as we don't send packets more often
2011-03-27 19:34:16 +11:00
e1ebf74ba0
more gen3 updates courtesy of sliptonic via IRC
2011-03-24 11:48:54 +11:00
d7f5c08174
all defines live in config.h now, remove from Makefile
2011-03-24 11:26:11 +11:00
918e3be84c
include thermistor tables, most users seem to have similar thermistors so we can safely provide a default
2011-03-24 11:06:04 +11:00
0ddb40a844
IDE apparently takes issue with Extruder.pde in extruder directory, altered capitalisation
2011-03-24 10:58:51 +11:00
081b693341
extruder doesn't use serial.c, update watchdog.c to suit
2011-03-24 10:51:57 +11:00
196caff134
Extruder: GEN3 and EXTRUDER defined in config, not Makefile
2011-03-24 10:31:33 +11:00
0dc7d77885
Massive Doxygen documentation addition
...
'make doc' then point your browser at doc/html/
Needs plenty of cleanup and polishing, but the main bulk is here
even documents your configuration! ;)
2011-03-22 01:34:36 +11:00
b03dd87665
config.h.dist: remove the Gen3 sample pinout.
...
As we have a config.gen3.h now, this is obsolete.
2011-03-20 16:09:21 +01:00
8b78c2a498
Make baud rate user-configurable.
2011-03-20 15:47:15 +01:00
1214646ca8
mendel.c: Repsnapper expects a lowercase "start".
2011-03-20 02:09:16 +01:00
f9842d1d90
extruder/config.h.dist: add fallbacks for non-Makefile compilation.
2011-03-19 22:15:22 +01:00
6e9dd81fb7
func.sh: add variable for serial device
2011-03-17 20:38:30 +11:00
851a91306a
timer.c: don't reset next_step_time when doing a step.
...
Doing so adds most of the interrupt execution time to the
step time, see line 126 of the same file:
if (next_step_time == 0) {
// new move, take current time as start value
step_start = TCNT1;
}
2011-03-14 17:34:26 +01:00
Michael Moon
Kieran Levin
Markus Hitter
Markus Amsler
Markus Amsler
Andy Kirby