340aea89c8
Config templates: publish ENABLE_PINs in _all_ templates.
...
No functional change, as the new ones are commented out.
2011-02-27 12:00:45 +01:00
7087587f19
Config templates: add MAX_PINS consistently.
...
No functional changes, since all the new ones are commented out.
2011-02-27 11:55:27 +01:00
5c31bc01c1
gcode_process.c: make special moves non-public.
...
This adds some 30 bytes program size for whatever reason.
2011-02-27 11:55:01 +01:00
1a33cfddf6
gcode_parse.h: grant mantissa full 32 bits.
...
This saves 280 bytes of binary size and probably quite a bit of
processing time. Cost: 1 byte of RAM.
2011-02-27 11:53:08 +01:00
bdeb4827fc
gcode_parse.c: replace some ints by uints to double the range.
...
This is without accuracy or other losses and should finally make
decfloat_to_int() free of variable overflow within the decribed
ranges. Surprisingly, this costs 14 bytes program size.
2011-02-27 11:51:19 +01:00
694e3c4298
Revert "Config templates: protect config.h against multiple inclusion."
...
Teacup uses preprocessor magic which actually requires including
config.h twice.
This reverts commit c61191d86d
2011-02-27 11:11:37 +01:00
8acb072e0b
Actually set extruder enable pin if defined
2011-02-27 00:55:14 +11:00
f985de8a54
gcode_parse.c: make decfloat_to_int handle all uints.
...
This saves 10 bytes of binary size and possible headaches (negative factors).
2011-02-25 11:54:22 +01:00
c61191d86d
Config templates: protect config.h against multiple inclusion.
...
This is a small compile time saver and also mandatory for
patches later in the queue.
2011-02-25 11:53:21 +01:00
758893c275
gcode_parse.c: ditch ASTERISK_IN_CHECKSUM_INCLUDED.
2011-02-25 11:49:51 +01:00
d705f46899
more cleanup after name change
2011-02-24 23:48:15 +11:00
4aefda6f17
added integer square root algorithm for future use
2011-02-24 18:49:28 +11:00
4ca9e470a5
Move timer macros from config.h.dist and derivates to timer.c.
...
This sould confuse users less and neither value is subject to change
per configuration. Reviewed also by Markus Amsler.
2011-02-23 12:37:15 +01:00
2c53dbe2a8
gcode_parse: limit decimal ranges by decfloat_to_int()'s demands.
...
Formerly, it was limited by variable bit ranges, which allowed
more than decfloat_to_int() can swallow.
2011-02-23 02:52:51 +01:00
0dc623d4eb
gcode_parse.c: added comments, which show possible variable overflows.
...
Stay tuned, the fix is just around the corner.
2011-02-23 02:52:27 +01:00
dfc4674012
dda.h: re-add a check against multiple acceleration types.
...
This was previously in config.h(.dist), but better belongs
to dda.h.
2011-02-23 02:51:43 +01:00
780dea1186
avr-libc's math is smaller than gcc's, use it
2011-02-21 19:09:08 +11:00
b8e6400a2d
more README updates
2011-02-21 16:47:00 +11:00
af36737e3b
update README
2011-02-21 16:24:21 +11:00
8188ff3593
merge intercom-protocol into master
2011-02-21 16:01:27 +11:00
bfae6ff97f
intercom: Reduce sections with disabled interrupts.
2011-02-21 15:52:17 +11:00
52c2788997
intercom: updating the extruder in 250ms intervals should be fast enough.
2011-02-21 15:52:17 +11:00
fa2a4389fc
intercom: Transmit/receive from/to temporary packets.
...
Fixes that the packet could be changed during transmit. And only values from packets with correct checksum are used.
2011-02-21 15:52:16 +11:00
5e56784ac1
extruder: Set/get bed temperature.
2011-02-21 15:52:16 +11:00
6d83bdb067
extruder: add fan definitions
2011-02-21 15:52:15 +11:00
e032cf5dab
extruder: Use pull up resistors for step/dir pin to avoid noise.
2011-02-21 15:52:15 +11:00
d0cbe86a2d
extruder: Half-step on every step signal.
...
No idea why only every 4th step signal would actually step, but this generates a lot of noise for nothing.
2011-02-21 15:52:15 +11:00
e3672da1cf
extruder: Check the step pin directly.
...
Flag could get out of sync, with undefined results.
2011-02-21 15:52:15 +11:00
5cf550733d
arduino_168: define AIO6/7
2011-02-21 15:52:14 +11:00
7aff5623ef
home: delay is in micro seconds
2011-02-21 15:52:14 +11:00
eecf3af9f1
analog mask calculated automagically
2011-02-21 13:57:51 +11:00
31634c6a8f
Add M136 (DEBUG) to read back PID values, add heater_print function
2011-02-20 17:30:07 +11:00
8540be950a
use CRC16 to verify heater PID settings in eeprom
2011-02-20 17:13:09 +11:00
9dc4d54133
fix compile error around new homing logic
2011-02-20 16:35:22 +11:00
c6122eda74
add G161/G162 commands, upgrade home.c to provide negative/positive homing calls for G161/G162
2011-02-20 14:10:53 +11:00
4426c69274
individual functions to home each axis
2011-02-20 13:39:07 +11:00
18d47056f5
print queue with every G command if debug is enabled
2011-02-20 11:37:13 +11:00
da9bfc9f6f
print_queue no longer adds a newline
2011-02-20 11:37:12 +11:00
65a1846955
bang-bang heater toggle is wrong way around
...
Signed-off-by: Michael Moon <triffid.hunter@gmail.com>
2011-02-20 11:02:18 +11:00
72adba5a58
apparently repg expects N preceding line numbers in resend requests
2011-02-19 13:09:21 +11:00
83fa3f7d09
disable greycode by default in arduino IDE
2011-02-17 21:52:15 +11:00
d06a365f54
G4 uses millisecond units now apparently, instead of seconds
2011-02-17 14:05:13 +11:00
f78a0483d7
make URLs in README easier to find
2011-02-17 11:22:57 +11:00
afe58621a2
M140: S value is a temperature
2011-02-15 13:24:54 +11:00
b0d1ba0e60
Fix analog reading of channel 0 if another channel is active.
2011-02-15 13:24:53 +11:00
bcd47e90b0
Fix analog reading of channel 0 if another channel is active.
2011-02-15 13:21:45 +11:00
3aa7fc83e4
M140: S value is a temperature
2011-02-15 13:21:45 +11:00
664337fa25
use proper feedrate for Y
2011-02-15 13:21:45 +11:00
940d474c6c
home to max should now return to zero after homing
2011-02-15 10:10:29 +11:00
c810875755
Fix PWM timer and steps/mm for extruder
2011-02-15 10:03:12 +11:00
Markus Hitter
Stephan Walter
Michael Moon
Markus Amsler
Architect