01f7c99881
config.h: introduce PS_MOSFET_PIN for Sanguish support.
2013-10-27 20:01:51 +01:00
ea59e634a7
Bring LOOKAHEAD into the config templates.
2013-07-11 22:02:23 +02:00
3c5d9d8950
Replace #define HOST by #define MOTHERBOARD.
...
Apparently, HOST conflicts with some AVR headers for the
USB-equipped ATmegas.
Patch by DaveX, thank you Dave. See also:
http://forums.reprap.org/read.php?147,33082,182021#msg-182021
2013-03-24 16:17:14 +01:00
64560eda45
config templates: bring in EECONFIG.
...
Recently EEPROM storage was wrapped in #ifdefs, so, to get it back
by default, we have to enable it.
2013-02-05 14:11:04 +01:00
6f2ec09837
Make temperature sensor type TT_NONE obsolete.
...
The requirement was simply neither obvious nor intuitive. Drawback
is, the indices of temperature sensors can now differ from these
of the heaters. That's easier to recognize for newbies, though.
2013-01-03 15:34:41 +01:00
ba05d6a0cd
Give up on REPRAP_HOST_COMPATIBILITY.
...
Was never really accepted and these days, hosts usually adjust
to the firmware instead of the other way around.
2012-12-03 19:50:14 +01:00
9b018b7433
Make USB_SERIAL fit for the Arduino IDE.
...
This also includes renaming of USE_USB to USB_SERIAL for more
consistency.
2012-12-03 19:49:58 +01:00
7c3920a552
Distribute on/off on PWM pins to all config templates.
2012-11-08 16:37:31 +01:00
8e27595a5f
temp.c: allow smoothing temperature readings.
...
This is done by an Exponentially Weighted Moving Average (EWMA)
formula. Contribution by DaveX, see
http://forums.reprap.org/read.php?147,33082,157978#msg-157978
Thanks a lot, Dave.
2012-11-08 16:22:31 +01:00
a054d4c6cd
Remove all remaining evidence of M109.
...
M109 went away a few commits ago in favour of only M116.
2012-10-14 22:57:22 +02:00
fd9985ac49
config templates: fix directly numbered/unused pins.
2012-09-29 22:59:22 +02:00
bfe5e6f2fc
Fixed ADC channel handling.
...
ADC pin is not the same as ADC channel in atmega1280/2560.
2012-09-29 22:57:55 +02:00
d967ad10c0
config.gen7-1.4.h: swap thermistor pins to match v1.4.1.
...
This works for v1.4, too, as the mapping was arbitrary, there.
2012-09-29 22:57:41 +02:00
5811b49b02
Config templates: comment out FAST_PWM by default.
...
Also, start to limit comments in the config templates to 80 chars,
to ease reading them in the Arduino IDE.
2012-08-17 16:02:02 +02:00
0ba62800eb
config template: adjust the comments for the heaters.
...
For example, heaters currently don't work on non-PWM pins. Also,
mention special names.
2012-08-04 22:08:43 +02:00
8c6e6a1027
Fix comment on STEPS_PER_M_x in config.h templates.
2012-08-04 22:08:35 +02:00
1657fb2731
Align heater definitions in config.h templates.
...
Purely cosmetical, no functional change.
2012-05-13 20:44:09 +02:00
9c126e3387
Adjust config.gen7-v1.4.h for Gen7 v1.4.
...
This means:
- Max endstops are gone.
- Min endstops are now PB0 / PB1 / PB2.
- Order of the steppers is inverted (X Y Z E instead of E Z Y X).
- All pins on port A one to the left (pin number - 1).
2012-05-13 20:40:22 +02:00
e8518f9e34
Allow the ATmega1284P on Gen7's.
2012-05-13 20:15:55 +02:00
99dec3189a
Split up config.h templates for the new Gen7 v1.4.
2012-05-13 20:14:58 +02:00
Markus Hitter
Mikko Sivulainen