Previously when the firmware called M701/M702 manually
there was no Z lift. But after we added support for the Z
parameter we set the default to 50mm.
Change strings "M701" to "M701 Z0" and "M702" to "M702 Z0"
to restore the previous behavior from before 3.13.
Also pulled the gcodes into PROGMEM in message.cpp
along with M83 and M84 to save memory.
Change in memory:
Flash: -34 bytes
SRAM: 0 bytes
* M600 used 1°C threshold, which may increase the waiting time a bit
* Wizard used 3°C
Sync both to use TEMP_HYSTERESIS for consistancy
No change in memory footprint
Use 5°C threshold to be consistant with other parts
of the firmware.
Relying on 95% of the target temperature creates
a dependency on the temperature:
PLA: Target = 215°C, threshold = 10.75°C
PETG: Target = 230°C, threshold = 11.5°C
ABS: Target = 255°C, threshold = 12.75°C
ASA: Target =260°C, threshold = 13.0°C
PC: Target = 275°C, threshold = 13.75°C
My proposal is we instead use a constant
TEMP_HYSTERESIS = 5, which is consistent with
M109, and behavior when restoring print from RAM
and some of the MMU code (like unload function)
Change in memory:
Flash: +2 bytes
SRAM: 0 bytes
This commit adds the ability for the firmware to dim and wake the
backlight when LCD updates are disabled. Such as in the MMU error screen
or when rendering full screen messages which typically
disable the LCD updates to prevent the status screen from rendering.
Fixes#2777
Change in memory:
Flash: -26 bytes
SRAM: +1 byte
Main changes:
* setAllTargetHotends() is removed
* setTargetHotendSafe() is removed
* Extruder parameter on setTargetHotend() is dropped
Change in memory:
Flash: -192 bytes
SRAM: 0 bytes
During calibration model warnings are possible/normal. This is
apparently leading some into thinking the hotend might be faulty
and abort the calibration with a hard reset.
Disable warnings/beeps during calibration.
Rely on the error threshold only.
During thermal errors all fans are set to full speed.
When the print is resumed or stopped *and* the thermal error is gone,
also restore the autofan state.
Fixes#3893
Running `M310 A` should set the TM calibration bit status if the
autotune procedure was successful.
Partially addresses #3891 and #3890, since running `M310 A F0` should
*still* count as valid calibration data and is not something that can be
replicated by using the LCD (which enforces self-test).
Alert messages are intended to persist above "info" messages, thus
preventing further calibration status updates to be shown (such as
thermal model calibration).
Just set the message as a regular status message.
Fixes#3892
This PR tries to address the 3 different startup scenarios for 1st layer calibration with the MMU:
- 1st lay cal started with correct filament already loaded in the nozzle - we should continue, but skip the first 58mm (first 2 g-codes in the hard coded sequence) of purge line extrusion
- 1st lay cal started with other filament already loaded in the nozzle - we should unload and then issue a toolchange with no extra unload
- 1st lay cal started without loaded filament - we should just do a toolchange with no extra unload
PFW-1457
Update the eeprom FW version as soon as migration is complete, to avoid
resetting the CALIBRATION_V2 variable at each reset.
Do not implicitly reset the calibration steps for WizState::Run: do this
only for the menu action.
Guðni Már Gilbert
3d-gussner
D.R.racer
Giles Bathgate
Yuri D'Elia
Alex Voinea