Remove a few redundant language.h includes
Also remove language.h include from cmdqueue.h to prevent including language.h unnecessarily
Fix missing message.h includes in a few files
* Sync PEC `FINDA_DIDNT_GO_OFF` to `FINDA_FILAMENT_STUCK`
* Sync PEC `FSENSOR_DIDNT_GO_OFF` to `FSENSOR_FILAMENT_STUCK`
* Sync PEC `PULLEY_STALLED` to `PULLEY_CANNOT_MOVE`
* Sync PEC `SELECTOR_CANNOT_MOVE` update text
* Sync PEC `IDLER_CANNOT_MOVE` update text
* Sync PEC `PULLEY_WARNING_TMC_TOO_HOT` to `WARNING_TMC_PULLEY_TOO_HOT`
* Snyc PEC `RestartMMU` to `ResetMMU`
Also related text
* Sync PEC `SELECTOR_WARNING_TMC_TOO_HOT` to `WARNING_TMC_SELECTOR_TOO_HOT`
* Sync PEC `IDLER_WARNING_TMC_TOO_HOT` to `WARNING_TMC_IDLER_TOO_HOT`
* Sync PEC `PULLEY_TMC_OVERHEAT_ERROR` to `TMC_PULLEY_OVERHEAT_ERROR`
* Sync PEC `SELECTOR_TMC_OVERHEAT_ERROR` to `TMC_SELECTOR_OVERHEAT_ERROR`
* Sync PEC `IDLER_TMC_OVERHEAT_ERROR` to `TMC_IDLER_OVERHEAT_ERROR`
* Sync PEC `PULLEY_TMC_DRIVER_ERROR` to `TMC_PULLEY_DRIVER_ERROR`
Also releated text
* Sync PEC `SELECTOR_TMC_DRIVER_ERROR` to `TMC_SELECTOR_DRIVER_ERROR`
Also related text
* Sync PEC `IDLER_TMC_DRIVER_ERROR` to `TMC_IDLER_DRIVER_ERROR`
Also related text
* Sync PEC `PULLEY_TMC_DRIVER_RESET` to `TMC_PULLEY_DRIVER_RESET`
* Sync PEC `SELECTOR_TMC_DRIVER_RESET` to `TMC_SELECTOR_DRIVER_RESET`
* Sync PEC `IDLER_TMC_DRIVER_RESET` to `TMC_IDLER_DRIVER_RESET`
* Sync PEC `PULLEY_TMC_UNDERVOLTAGE_ERROR` to `TMC_PULLEY_UNDERVOLTAGE_ERROR`
* Sync PEC `SELECTOR_TMC_UNDERVOLTAGE_ERROR` to `TMC_SELECTOR_UNDERVOLTAGE_ERROR`
* Sync PEC `IDLER_TMC_UNDERVOLTAGE_ERROR` to `TMC_IDLER_UNDERVOLTAGE_ERROR`
* Sync PEC `PULLEY_TMC_DRIVER_SHORTED` to `TMC_PULLEY_DRIVER_SHORTED`
Also related text
* Sync PEC `SELECTOR_TMC_DRIVER_SHORTED` to `TMC_SELECTOR_DRIVER_SHORTED`
Also related text
* Sync PEC `IDLER_TMC_DRIVER_SHORTED` to `TMC_IDLER_DRIVER_SHORTED`
Also related text
* Sync PEC `PULLEY_SELFTEST_FAILED` to `MMU_PULLEY_SELFTEST_FAILED`
Also related text
* Sync PEC `SELECTOR_SELFTEST_FAILED` to `MMU_SELECTOR_SELFTEST_FAILED`
Also releated text
* Sync PEC `IDLER_SELFTEST_FAILED` to `MMU_IDLER_SELFTEST_FAILED`
Also related text
* Sync PEC fix MMU_MMU
Update MMU MCU UNDERPOWER
* Sync PEC `FIL_ALREADY_LOADED` to `FILAMENT_ALREADY_LOADED`
Also related text
* Add Prusa Error Codes check script
* Remove `:` at FINDA and FSENSOR as it is in other tiles
* Sync
FSENSOR_DIDNT_TRIGGER
MSG_DESC_SELECTOR_CANNOT_MOVE
MSG_DESC_IDLER_CANNOT_MOVE
MSG_DESC_FW_UPDATE_NEEDED
FILAMENT_ALREADY_LOADED
* Add MMU UNKOWN_ERROR PEC
bFilamentAction variable is never reset, even after
disabling the heaters.
Steps to reproduce:
1. Boot-up printer
2. Select Load to Nozzle.
3. Select PLA (215°C) target
4. Select Filament 1
5. Wait for load to be successful
6. Go to Preheat submenu and select Cooldown (last menu item)
7. Observe target temperature on the status screen is now 0°C
8. Select Load to Nozzle again.
9. Select Filament 2.
* Expected behavior target temperature IS NOT 0°C
* Actual behavior target temperature IS 0°C
Change in memory:
Flash: -26 bytes
SRAM: 0 bytes
Sync with the 32-bit side.
The ReportingRAII does not handle recursion.
Fixes an issue with the multiple calls to
BeginReport() and EndReport()
Change in memory:
Flash: +14 bytes
SRAM: 0 bytes
If the protocol reports and error and give errorCode
a value. When the error is resolved, errorCode is not reset to OK.
If the MMU is not in an error state I would expect errorCode to reflect that.
This fixes MMUCurrentErrorCode()
Change in memory:
Flash: +12 bytes
SRAM: 0 bytes
Guðni Már Gilbert
Alex Voinea
3d-gussner