b2b7990cfc
Allow tweaking try-unload feedrates
...
It looks like MMU2_VERIFY_LOAD_TO_NOZZLE_FEED_RATE can get much higher that the original 20mm/s.
50mm/s is the default now, can be tweaked further.
2022-12-30 14:23:44 +01:00
c5d2aedfe4
wizard: Ask about the sheet before doing Z calibration
...
Ask to install the sheet immediately after removing the test print.
This makes further messages less confusing.
2022-12-30 14:14:01 +01:00
66071c0b5b
wizard: Resume the wizard for missing calibrations during upgrades
...
Instead of checking for explicit versions, resume the wizard if some
(new) wizard is missing.
This handles both the old SELFTEST check, the new thermal model
and any future check in the same fashion.
2022-12-30 14:14:01 +01:00
2a1511f7b1
Read version data from progmem in eeprom_fw_version_older_than
2022-12-30 14:14:01 +01:00
dd99b1ab32
wizard: Disable temperature model during hotend testing
...
This avoids confusing error messages if the hotend is defective and
caught by selftest itself.
Rearrange Stopped state checks (saves 2 bytes)
2022-12-30 14:14:01 +01:00
8fa0a22b8d
wizard: Allow partial resuming after reset
...
Update the eeprom FW version as soon as migration is complete, to avoid
resetting the CALIBRATION_V2 variable at each reset.
Do not implicitly reset the calibration steps for WizState::Run: do this
only for the menu action.
2022-12-30 14:14:01 +01:00
414972c876
Unbreak build with !PINDA_THERMISTOR
2022-12-30 14:14:01 +01:00
7828788e5c
Handle CALIBRATION_STATUS_TEMP_MODEL
2022-12-30 14:14:01 +01:00
2a13ce4c62
Handle CALIBRATION_STATUS_SELFTEST
2022-12-30 14:14:01 +01:00
b8c1f34e31
Handle CALIBRATION_STATUS_{Z,XYZ}
2022-12-30 14:14:01 +01:00
b41ece175b
Handle CALIBRATION_STATUS_LIVE_ADJUST
2022-12-30 14:14:01 +01:00
5ec627c12c
wizard: Rewrite the fw upgrade check logic
...
- Handle the conversion from the V1 calibration status to the V2 bitmap
for all past FW versions.
- Allow to run the wizard in "Restore" mode (for example during upgrade
or service prep) to complete any missing steps.
- Fix service prep to use the above feature by clearing the appropriate
calibration bits.
- Remove exceptions for FW 3.2.0.4 which can now be handled cleanly.
2022-12-30 14:14:01 +01:00
22c0e15047
wizard: Rewrite the wizard handling loop
...
Simplify status tracking:
- S::Restore to continue to the next logical wizard item
- S::Finish for a successful failure
- S::Failed to exit while showing a failure
2022-12-30 14:14:01 +01:00
a712546269
wizard: Remove unused wizard stages
...
Remove PreheatPla/IsPla, as we currently always explicitly ask for the
material type.
2022-12-30 14:14:01 +01:00
da6e56a17e
Simplify altfan override initialization
2022-12-30 14:14:01 +01:00
9a018230ce
Replace calibration state with a new calibration bitmap
...
- Move calibration status/declarations to util.h
- Allows to query the status of each step independently without assuming
any order
- Allows to extend the calibration with new steps transparently
2022-12-30 14:14:01 +01:00
2552fee4c7
eeprom: Fix EEPROM_HEAT_BED_ON_LOAD_FILAMENT debug offset in docs
2022-12-30 14:14:01 +01:00
0e2c2d9eea
Simplify FW eeprom version checks
...
- Generalize force_selftest_if_fw_version() so we can check when upgrading
between arbitrary FW versions.
- Do not call update_current_firmware_version_to_eeprom() prematurely
when forcing self-test (if a reset happens before self-test completes,
the check would be incorrectly skipped on the next run).
2022-12-30 14:14:01 +01:00
74609009ca
Fix M117 string offset
2022-12-30 14:06:48 +01:00
9105573ac9
Handle/strip leading whitespace in gcode stream
2022-12-30 14:06:48 +01:00
a4d427adf2
De-specialize M0/M1/M117
...
Since we no longer scan for the first command these exceptions can be
removed.
2022-12-30 14:06:48 +01:00
bb1e438f00
Do not scan for GMTD commands
...
Expect these to be always at the start of the line.
2022-12-30 14:06:48 +01:00
f46be49f7d
Tighten parsing of M0/M1/M117/PRUSA
...
Expect these to be always at the start of the command (which is now
stripped of the extra line number), reducing the number of corner cases
due to these not following the g-code spec.
2022-12-30 14:06:48 +01:00
7c896a87a4
Remove '*' (checksum) handling in process_commands
...
The checksum is already removed from the command queue so there's no
need to reprocess it in the main loop.
2022-12-30 14:06:48 +01:00
6651f5ce8b
Strip the line number from the command queue
...
This increases the number of commands that can be queued and at the same
time it avoids a considerable amount of rescanning in a critical path.
2022-12-30 14:06:48 +01:00
797513d3c5
Remove T parameter from M221
...
Fixes #3852
2022-12-30 13:07:56 +01:00
4219beed71
Remove initial cursor setting
...
The cursor position is controlled by
the for-loop
Change in memory:
Flash: -8 bytes
SRAM: 0 bytes
2022-12-30 12:57:07 +01:00
1186b36bfa
Remove whitespace at start of new row
2022-12-30 12:57:07 +01:00
7529eaec44
Remove duplicate code
...
msg_next is NULL, then the end of the message has been reached.
Change in memory:
Flash: -24 bytes
SRAM: 0 bytes
2022-12-30 12:57:07 +01:00
5037d1edbc
delay_keep_alive calls manage_heater and manage_inactivity
...
No need to call them again, the for-loop is very quick
Change in memory:
Flash: -10 bytes
SRAM: 0 bytes
2022-12-30 12:57:07 +01:00
1a9b7d79e6
Don't handle whitespace in a special way
...
Instead of reading and checking if a character is a whitespace
just print it out onto the LCD. This makes the code a bit less
complex. Whether there is a whitespace character, we always end
up reading from program space, so I doubt this has much performance
impact.
Change in memory:
Flash: -38 bytes
SRAM: 0 bytes
2022-12-30 12:57:07 +01:00
7925df6aa0
Default check action is continuing
2022-12-30 12:49:57 +01:00
96707aadcb
Fix timeout making UI freeze
2022-12-30 12:49:57 +01:00
92cf8da45e
Remove unused defines
2022-12-30 12:49:57 +01:00
df65212449
Add yes-no choice to M862 warning
...
Fixes #3421
Change in memory:
Flash: -98 bytes
SRAM: 0 bytes
2022-12-30 12:49:57 +01:00
cc3d36c78f
Replace labs with fabs
...
Both degHotend and degTargetHotend return a float
In this case it is better to use fabs()
Change in memory:
Flash: -14 bytes
SRAM: 0 bytes
2022-12-29 08:54:50 +01:00
03511a5a7c
Remove redundant ultralcd includes in Marlin_main
...
This also removes two definitions
- ULTRALCD
- LCD_USE_I2C_BUZZER
Neither of them are defined anywhere
2022-12-27 12:03:56 +00:00
9757502abc
Remove pins_arduino.h include
...
This header is already included with Arduino.h which
is included in Marlin.h header.
2022-12-27 12:03:14 +00:00
72857c902c
drop conv2str dependency in Marlin_main
2022-12-27 11:59:22 +00:00
fea608c8c4
A few more meassuring typos
2022-12-22 12:54:42 +01:00
b3790f4094
Typo: meassure -> measure
2022-12-22 12:54:42 +01:00
52941b1111
Rename xyzcal_meassure_center back to xyzcal_meassure_enter
...
Keep the enter/leave pairs
2022-12-22 12:54:42 +01:00
515a625180
Typo: hysterezis -> hysteresis
2022-12-22 12:54:42 +01:00
8414c272bf
Merge pull request #3787 from gudnimg/PFW-1439
...
PFW-1448 Fix underextrusion + compensate load to nozzle extruder sequence for Extra Loading Distance
2022-12-22 11:07:28 +01:00
9ca7760c2e
Merge pull request #3830 from 3d-gussner/MK3_XYZ_cal_fix
...
MK3: XYZ cal change message and add LCD ouput
2022-12-20 14:16:49 +01:00
0bcb4ab59d
Merge pull request #3822 from wavexx/tm_partial_lock
...
MK3: TM: Prevent lockout on invalid model values
2022-12-20 14:13:56 +01:00
7fef570d1b
Change xyz cal message `up to 24 min.` instead `approx. 12 min.`
2022-12-20 10:30:53 +01:00
355b670cd4
Remove SWSPI which is not used/implemented
2022-12-20 10:10:45 +01:00
2b38080c7e
Merge pull request #3833 from leptun/MK3_fix_MK2.5_softReset
2022-12-20 10:02:14 +01:00
ea6450f072
Add LCD output during xyz calibration
2022-12-20 08:36:19 +01:00
D.R.racer
Yuri D'Elia
Guðni Már Gilbert
Alex Voinea
3d-gussner