ba0f051f72
Revert accidental removal of check
2022-12-18 15:55:48 +01:00
8623d9ff55
Split the mmu2 config into MMU2 and MMU2S
2022-12-18 09:58:20 +01:00
c8157919b1
PFW-1440 Fix issue where cooldown timer is not set after a faile retry
2022-11-21 12:54:53 +01:00
37ac33bc32
Fix compiler warning
2022-11-21 12:54:53 +01:00
fe6e3ca2b1
Unload first before retrying
...
Should free the filament if accidentally held by the fsensor.
2022-11-20 19:23:07 +01:00
5639620041
Avoid watchdog while doing VerifyFilamentEnteredPTFE
2022-11-20 17:27:36 +01:00
84d9eee61d
Resume hotend temperature if parked + MMU restarted
...
PFW-1355
2022-11-20 17:27:36 +01:00
01c1f4a8dd
Load test: Monitor unload as well
2022-11-20 17:27:36 +01:00
5c8ea4c90a
fixup
2022-11-20 17:27:36 +01:00
327f0edb17
VerifyFilamentEnteredPTFE must take into account the Extra Loading Distance
2022-11-20 17:27:36 +01:00
c9d9ba0b1a
Add a bracket around subtraction, just in case
2022-11-20 17:27:36 +01:00
ef51b5778d
Fix VerifyFilamentEnteredPTFE
...
Test should push filament first and then retract.
2022-11-20 17:27:36 +01:00
a17153f877
Make TMC mask more readable
2022-11-20 17:27:36 +01:00
f1ed2fc5c7
Fix issue where tool_change_extruder is not reset after retry
2022-11-20 17:27:36 +01:00
46f4f2658d
PFW-1432 Reduce LOC
...
If verification test fails, increment load fail statistic
2022-11-20 17:27:36 +01:00
03235c8aab
PFW-1432 restore toolchange load testing
2022-11-20 17:27:36 +01:00
adb24cd410
Increment errors in ReportError
2022-11-20 17:27:36 +01:00
4eaabbf092
Revive MMU stats + LCD screens
2022-11-20 17:27:36 +01:00
fe11b7a247
Tune Interrupted state based on unit tests
...
Now finally the printer can restart ToolChange if MMU restarted.
2022-11-20 17:27:36 +01:00
ffbd95b482
Unify naming convention (index->slot)
...
in all top level MMU-related functions
2022-11-20 17:27:36 +01:00
e414413b2e
Refactor ToolChange+LoadToNozzle
...
Add basic infrastructure for handling of repeated commands until they finish correctly.
2022-11-20 17:27:36 +01:00
10a9e0f0a0
Recover from MMU restart while performing a command
...
PFW-1427
2022-11-20 17:27:36 +01:00
e11ef11a64
PFW-1425 Rename "Load to Extruder" to "Loading Test"
2022-11-16 06:00:15 +01:00
006fe110cc
Don't raise MMU error screen until retry is done
...
Change in memory:
Flash: +8 bytes
SRAM: 0 bytes
2022-11-12 18:47:10 +01:00
68bd7f9b19
Fix excessive flash usage.
2022-11-12 18:47:10 +01:00
ecef69012a
Fix PFW-1364 & possible comms timeout during reheat
2022-11-12 18:47:10 +01:00
a896dfd4e0
PFW-1397 To reserve EEPROM write cycles, only update toolchange counter when a print finishes or is stopped
2022-11-08 13:49:40 +01:00
3120bf0aa2
PFW-1397 Implement new function increment_tool_change_counter()
...
Reduces flash consumption by 44 bytes
2022-11-08 13:49:40 +01:00
5a60a85467
PFW-1397 Increment toolchange statistic
2022-11-08 13:49:40 +01:00
7bc7f21fa5
mmu: move RetryIfPossible outside the error screen
...
This fixes issue where 'retryAttempts=3' may be spammed in the logs
Change in memory:
Flash: 0 bytes
SRAM: 0 bytes
2022-11-01 06:22:39 +01:00
0aeb74e5b1
Intercept M708 A0xb: set ExtraLoadDistance on the printer side too
2022-10-11 15:51:01 +02:00
b0466ae20f
Add infrastructure for MMU parametrization after comm start
...
For now, only the Extra loading distance is being sent, but the infrastructure can be easily extended for other registers as well.
2022-10-11 15:51:01 +02:00
c7e4c9ce99
Allow backwards compatibility with legacy MMU g-codes
...
This piece just changes the default extra load length on the MK3 side.
The same needs to be done on the MMU side but:
- the MMU exposes its register for this (so we can change the extra load distance by writing into the register via G-code)
- the printer shall probably set this value on its own after line up of MMU communication
2022-10-11 15:51:01 +02:00
d5ca47d1a6
Merge pull request #3646 from gudnimg/fix-mmu-buttons-v2
...
PFW-1403 Fix issue where physical MMU buttons do not dismiss error screen
2022-10-11 13:42:39 +02:00
8882d8f2c8
Only move XY when position is known
...
I had a crash when producing an error screen and printer was unhomed.
Extruder was located at the far right side, and immediately crashed when attempting to park.
2022-10-11 07:16:52 +02:00
d6e0f47739
PFW-1403 Rename ReportErrorSource to ErrorSource for shorter code
2022-10-08 08:51:32 +00:00
33690b927a
PFW-1403 Fix issue where physical MMU buttons do not dismiss error screen
2022-10-08 08:51:32 +00:00
c7b6b9a99b
cleanup: Suppress unused argument warnings
2022-09-30 15:08:11 +02:00
183e21aa0b
Merge pull request #3599 from 3d-gussner/MK3_MMU2_messages
...
PFW-1339 - Update MMU2 translations
2022-09-21 10:27:01 +02:00
28b0ef1acb
PFW-1369 Use same ramming sequence as default settings in Slicer
2022-09-19 07:23:03 +02:00
88b58cdcd5
Update messages missing c= r=
...
Change MMU2 KEEPALIVE_STATE to IN_PROCESS
2022-09-16 19:24:11 +02:00
f4f09e4062
update mmu2 messages c= r= values
2022-09-16 19:18:23 +02:00
50b6044703
Use origin message on serial
2022-09-16 18:17:50 +02:00
edad625cf7
RIP Bondtech long live the Extruder
2022-09-16 16:31:27 +02:00
e9f5a95d4b
PFW-1362 Make sure FINDA runout is impossible with MMU disabled
...
Since mmu_loop() is called in the main loop() function
when the MMU is disabled, we need to utilise the
MMU protocol layer to prevent FINDA runout from happening
if MMU is disabled.
We also need to keep in mind we probably can't trigger
a FINDA runout in the middle of a Q0 query.
So my solution now is to wait for the "Finished" state
and check if the FINDA is off during printing.
When "Finished" state appears, the FINDA value should be up
to date.
2022-09-16 10:23:47 +02:00
63b4abb66d
PFW-1362 SpoolJoin needs to known what the previous slot was
2022-09-16 10:23:47 +02:00
8610636906
PFW-1362 Add a log when FINDA filament runout is triggered
2022-09-16 10:23:47 +02:00
715af8fcc2
Rename files to SpoolJoin
2022-09-16 10:23:47 +02:00
afc67332c7
PFW-1362 Initial commit
2022-09-16 10:23:47 +02:00
4d3a5433ad
Implement read/write registers for M707/M708
2022-09-16 10:23:47 +02:00
Alex Voinea
Guðni Már Gilbert
D.R.racer
VintagePC
3d-gussner
Yuri D'Elia