bb1e438f00
Do not scan for GMTD commands
...
Expect these to be always at the start of the line.
2022-12-30 14:06:48 +01:00
f46be49f7d
Tighten parsing of M0/M1/M117/PRUSA
...
Expect these to be always at the start of the command (which is now
stripped of the extra line number), reducing the number of corner cases
due to these not following the g-code spec.
2022-12-30 14:06:48 +01:00
7c896a87a4
Remove '*' (checksum) handling in process_commands
...
The checksum is already removed from the command queue so there's no
need to reprocess it in the main loop.
2022-12-30 14:06:48 +01:00
6651f5ce8b
Strip the line number from the command queue
...
This increases the number of commands that can be queued and at the same
time it avoids a considerable amount of rescanning in a critical path.
2022-12-30 14:06:48 +01:00
797513d3c5
Remove T parameter from M221
...
Fixes #3852
2022-12-30 13:07:56 +01:00
4219beed71
Remove initial cursor setting
...
The cursor position is controlled by
the for-loop
Change in memory:
Flash: -8 bytes
SRAM: 0 bytes
2022-12-30 12:57:07 +01:00
1186b36bfa
Remove whitespace at start of new row
2022-12-30 12:57:07 +01:00
7529eaec44
Remove duplicate code
...
msg_next is NULL, then the end of the message has been reached.
Change in memory:
Flash: -24 bytes
SRAM: 0 bytes
2022-12-30 12:57:07 +01:00
5037d1edbc
delay_keep_alive calls manage_heater and manage_inactivity
...
No need to call them again, the for-loop is very quick
Change in memory:
Flash: -10 bytes
SRAM: 0 bytes
2022-12-30 12:57:07 +01:00
1a9b7d79e6
Don't handle whitespace in a special way
...
Instead of reading and checking if a character is a whitespace
just print it out onto the LCD. This makes the code a bit less
complex. Whether there is a whitespace character, we always end
up reading from program space, so I doubt this has much performance
impact.
Change in memory:
Flash: -38 bytes
SRAM: 0 bytes
2022-12-30 12:57:07 +01:00
7925df6aa0
Default check action is continuing
2022-12-30 12:49:57 +01:00
96707aadcb
Fix timeout making UI freeze
2022-12-30 12:49:57 +01:00
92cf8da45e
Remove unused defines
2022-12-30 12:49:57 +01:00
df65212449
Add yes-no choice to M862 warning
...
Fixes #3421
Change in memory:
Flash: -98 bytes
SRAM: 0 bytes
2022-12-30 12:49:57 +01:00
cc3d36c78f
Replace labs with fabs
...
Both degHotend and degTargetHotend return a float
In this case it is better to use fabs()
Change in memory:
Flash: -14 bytes
SRAM: 0 bytes
2022-12-29 08:54:50 +01:00
03511a5a7c
Remove redundant ultralcd includes in Marlin_main
...
This also removes two definitions
- ULTRALCD
- LCD_USE_I2C_BUZZER
Neither of them are defined anywhere
2022-12-27 12:03:56 +00:00
9757502abc
Remove pins_arduino.h include
...
This header is already included with Arduino.h which
is included in Marlin.h header.
2022-12-27 12:03:14 +00:00
72857c902c
drop conv2str dependency in Marlin_main
2022-12-27 11:59:22 +00:00
fea608c8c4
A few more meassuring typos
2022-12-22 12:54:42 +01:00
b3790f4094
Typo: meassure -> measure
2022-12-22 12:54:42 +01:00
52941b1111
Rename xyzcal_meassure_center back to xyzcal_meassure_enter
...
Keep the enter/leave pairs
2022-12-22 12:54:42 +01:00
515a625180
Typo: hysterezis -> hysteresis
2022-12-22 12:54:42 +01:00
8414c272bf
Merge pull request #3787 from gudnimg/PFW-1439
...
PFW-1448 Fix underextrusion + compensate load to nozzle extruder sequence for Extra Loading Distance
2022-12-22 11:07:28 +01:00
9ca7760c2e
Merge pull request #3830 from 3d-gussner/MK3_XYZ_cal_fix
...
MK3: XYZ cal change message and add LCD ouput
2022-12-20 14:16:49 +01:00
0bcb4ab59d
Merge pull request #3822 from wavexx/tm_partial_lock
...
MK3: TM: Prevent lockout on invalid model values
2022-12-20 14:13:56 +01:00
7fef570d1b
Change xyz cal message `up to 24 min.` instead `approx. 12 min.`
2022-12-20 10:30:53 +01:00
355b670cd4
Remove SWSPI which is not used/implemented
2022-12-20 10:10:45 +01:00
2b38080c7e
Merge pull request #3833 from leptun/MK3_fix_MK2.5_softReset
2022-12-20 10:02:14 +01:00
ea6450f072
Add LCD output during xyz calibration
2022-12-20 08:36:19 +01:00
65f5b9e53d
Merge pull request #3818 from wavexx/tm_default_state
...
TM: Provide full defaults for model data and enable it by default
2022-12-20 07:08:25 +01:00
62ea78d46e
Handle configurable distance past gears
2022-12-19 23:49:12 +01:00
70356b71df
Handle filament sensor position that is not 0
2022-12-19 23:41:43 +01:00
c72ae8a2f3
PFW-1439 Remove parameters from execute_load_to_nozzle_sequence
2022-12-19 21:12:12 +00:00
6ee5f08505
PFW-1439 Compensate load to nozzle extruder sequence for Extra Loading Distance
...
The Extra Loading Distance is configurable by the user.
We need to compensate the hardcoded sequence
such that it does not extrude too much or
too little. Currently the firmware
extrudes too little.
2022-12-19 21:12:11 +00:00
97ddcc66bb
Merge pull request #3839 from leptun/MMU2_split_variant_config
...
MMU2 split variant config
2022-12-19 20:31:01 +01:00
c0f96e062b
TM: Force initialization after reset
2022-12-19 18:08:01 +01:00
ba0f051f72
Revert accidental removal of check
2022-12-18 15:55:48 +01:00
4c32e8b403
PFW-1457 make CHECK_FSENSOR into a function
2022-12-18 12:23:20 +00:00
5c1c6d9f3b
Adjust MMU2 specific distances
2022-12-18 10:30:43 +01:00
8623d9ff55
Split the mmu2 config into MMU2 and MMU2S
2022-12-18 09:58:20 +01:00
fee68b0f0d
PFW-1457 Do not unload at start of First Layer Cal
...
Fixes issue where First Layer Cal. triggers an unload before any
filament is loaded
The purpose of this if() statement is to handle the case where
a user or developer is sending T-codes to the printer directly
via Serial. Such as when one first sends T0 and then T4.
And unload must be triggered in-between, we can do this automatically
if FINDA detect filament.
Change in memory:
Flash: -10 bytes
SRAM: 0 bytes
2022-12-18 05:51:21 +00:00
dba3428ef2
Improve MSG_ACK_ERROR message
2022-12-17 20:25:47 +01:00
80c7790e87
Also prevent longpress when Stopped
2022-12-17 17:30:44 +01:00
271523ad45
TM: Disallow preheat/filament actions when stopped
...
Require acknowledgement first
2022-12-17 17:00:33 +01:00
f8290f25cd
TM: Allow to resume without a running print
...
If there is no running print, and the printer is Stopped, add a new
"Acknowledge error" menu entry to unlock the printer.
This simply calls lcd_print_stop(), which is identical in behavior to a
thermal error with a running print.
2022-12-17 16:48:39 +01:00
0972ef70d0
Use menu_set_block() in ThermalStop()
...
Set a menu block for fatal thermal errors instead of abusing
lcd_return_to_status() to kick the user out of the menus.
This now allows a thermal model error to be recoverable through menu
access.
2022-12-17 16:42:22 +01:00
8d719efa79
Do not show/call LCD status updates when unchanged
...
This mostly prevents useless serial noise
2022-12-17 16:35:26 +01:00
365f845c99
TM: correctly mark repeated anomalies
2022-12-17 16:33:42 +01:00
6e2f016655
TM: Clear the Stopped state when stopping the current print
...
We allow resuming from the LCD via start print and resume print,
it makes sense to clear the error on stop too.
For this reason distinguish whether the action is performed
automatically or manually (ie: interactively).
The error is only cleared when the command is run interactively.
2022-12-17 16:11:31 +01:00
119dc10b8f
Rename print_stop() to lcd_print_stop_finish() for clarity
2022-12-17 16:03:03 +01:00
Yuri D'Elia
Guðni Már Gilbert
Alex Voinea
3d-gussner