ed9f56a9d8
look-ahead: move jerk definitions into config.h templates.
2014-03-04 19:29:28 +01:00
01f7c99881
config.h: introduce PS_MOSFET_PIN for Sanguish support.
2013-10-27 20:01:51 +01:00
ea59e634a7
Bring LOOKAHEAD into the config templates.
2013-07-11 22:02:23 +02:00
3c5d9d8950
Replace #define HOST by #define MOTHERBOARD.
...
Apparently, HOST conflicts with some AVR headers for the
USB-equipped ATmegas.
Patch by DaveX, thank you Dave. See also:
http://forums.reprap.org/read.php?147,33082,182021#msg-182021
2013-03-24 16:17:14 +01:00
64560eda45
config templates: bring in EECONFIG.
...
Recently EEPROM storage was wrapped in #ifdefs, so, to get it back
by default, we have to enable it.
2013-02-05 14:11:04 +01:00
6f2ec09837
Make temperature sensor type TT_NONE obsolete.
...
The requirement was simply neither obvious nor intuitive. Drawback
is, the indices of temperature sensors can now differ from these
of the heaters. That's easier to recognize for newbies, though.
2013-01-03 15:34:41 +01:00
ba05d6a0cd
Give up on REPRAP_HOST_COMPATIBILITY.
...
Was never really accepted and these days, hosts usually adjust
to the firmware instead of the other way around.
2012-12-03 19:50:14 +01:00
9b018b7433
Make USB_SERIAL fit for the Arduino IDE.
...
This also includes renaming of USE_USB to USB_SERIAL for more
consistency.
2012-12-03 19:49:58 +01:00
7c3920a552
Distribute on/off on PWM pins to all config templates.
2012-11-08 16:37:31 +01:00
8e27595a5f
temp.c: allow smoothing temperature readings.
...
This is done by an Exponentially Weighted Moving Average (EWMA)
formula. Contribution by DaveX, see
http://forums.reprap.org/read.php?147,33082,157978#msg-157978
Thanks a lot, Dave.
2012-11-08 16:22:31 +01:00
a054d4c6cd
Remove all remaining evidence of M109.
...
M109 went away a few commits ago in favour of only M116.
2012-10-14 22:57:22 +02:00
fd9985ac49
config templates: fix directly numbered/unused pins.
2012-09-29 22:59:22 +02:00
bfe5e6f2fc
Fixed ADC channel handling.
...
ADC pin is not the same as ADC channel in atmega1280/2560.
2012-09-29 22:57:55 +02:00
5811b49b02
Config templates: comment out FAST_PWM by default.
...
Also, start to limit comments in the config templates to 80 chars,
to ease reading them in the Arduino IDE.
2012-08-17 16:02:02 +02:00
0ba62800eb
config template: adjust the comments for the heaters.
...
For example, heaters currently don't work on non-PWM pins. Also,
mention special names.
2012-08-04 22:08:43 +02:00
8c6e6a1027
Fix comment on STEPS_PER_M_x in config.h templates.
2012-08-04 22:08:35 +02:00
1657fb2731
Align heater definitions in config.h templates.
...
Purely cosmetical, no functional change.
2012-05-13 20:44:09 +02:00
eaf6c453be
Introduce gcode_init() and honor E_ABSOLUTE as the default.
2012-05-11 13:50:51 +02:00
7b909fcf82
Fix thermistor tables, which also fixes a build failure.
...
Now we don't have tables for default or gen7 electronics, but
two default tables for a single vs. two different thermistors.
This seems to be more logical.
2012-03-25 16:16:48 +02:00
86e20580f8
Make fast PWM optional.
...
In some cases the heater switching MOSFETs overheat and using a lower
PWM frequency is advised. See also:
http://reprap.org/wiki/Gen7_Research#Heat_vs._PWM_Frequency
2012-03-03 16:56:36 +01:00
56258a3908
Configuration samples: don't use preprocessor math for STEPS_PER_M.
...
Since the introduction of STEPS_PER_M instead of STEPS_PER_MM
it's no longer allowed. Unfortunately.
2011-12-13 03:30:03 +01:00
71fb5d6f47
configs: make F_CPU UL instead of L.
2011-12-04 18:36:15 +01:00
4e5f51f01e
Store distances in the TARGET strucure in micrometers for all axes.
...
This extends the previous commit from X to Y, Z and E.
2011-11-17 13:48:36 +01:00
c96ea0c773
Store distances in the TARGET structure always in micrometers.
...
This is a intrusive patch and for now, it's done for the X axis only.
To make comparison with the former approach easier ...
The advantages of this change:
- Converting from mm to steps in gcode_parse.c and back in dda.c
wastes cycles and accuracy.
- In dda.c, UM_PER_STEP simply goes away, so distance calculations
work now with STEPS_PER_MM > 500 just fine. 1/16 microstepping
on threaded rods (Z axis) becomes possible.
- Distance calculations (feedrate, acceleration, ...) become much
simpler.
- A wide range of STEPS_PER_M can now be handled at reasonable
(4 decimal digit) accuracy with a simple macro. Formerly,
we were limited to 500 steps/mm, now we can do 4'096 steps/mm
and could easily raise this another digit.
Disadvantages:
- STEPS_PER_MM is gone in config.h, using STEPS_PER_M is required,
because the preprocessor refuses to compare numbers with decimal
points in them.
- The DDA has to store the position in steps anyways to avoid
rounding errors.
2011-11-17 13:48:26 +01:00
b80c736004
Add the missing E_INVERT_ENABLE to the config templates.
...
Catch by brnrd, thanks.
2011-10-28 13:22:15 +02:00
eabf3d8e4c
config.ramps-1.2.h: invert X/Y/Z enable pins by default.
...
Suggestion by brnrd, thanks.
2011-10-28 13:22:14 +02:00
129bdc64bc
home.c: introduce SLOW_HOMING
2011-10-23 19:51:48 +02:00
df693c0113
config.h/dda.c: make endstop debouncing steps configurable.
2011-10-23 19:51:46 +02:00
448df5d1c3
config.*.h: raise default acceleration values.
...
Recommendation by Sublime, see
http://forums.reprap.org/read.php?147,99780,99912#msg-99912
2011-10-05 14:13:44 +02:00
e88becbad9
Config: don't enable soft axis limits by default.
...
This is confusing for newbies when their host of choice tries
to move into negative space.
You know ...
"Just installed Teacup and it's trash, because motors don't move!"
2011-10-05 14:13:32 +02:00
f9a4495aa1
Introduce TEMP_NONE, a "sensor" just storing the target temperature.
...
This is useful when operation a milling spindle. In this case,
set the spindle speed with M104 Sxxx, where xxx is 1..255.
M104 S0 turns the spindle off.
2011-09-01 19:03:33 +02:00
58f4678253
Catch by RobertFach: compatibility option for RepRap Host 20110509.
2011-08-30 12:01:48 +02:00
b1d8fd4a1f
Renamed old RAMPS config file because another version was created.
2011-08-16 14:05:41 +02:00
Markus Hitter
Mikko Sivulainen
Bas Laarhoven