Set a menu block for fatal thermal errors instead of abusing
lcd_return_to_status() to kick the user out of the menus.
This now allows a thermal model error to be recoverable through menu
access.
We allow resuming from the LCD via start print and resume print,
it makes sense to clear the error on stop too.
For this reason distinguish whether the action is performed
automatically or manually (ie: interactively).
The error is only cleared when the command is run interactively.
In M600 and M702, the Z-lift is taken care of outside this function
so it makes no sense to have a Z-lift within unload_filament()
Only exception to this is in the wizard, there I moved the Z-lift to
happen before we start heating the nozzle.
Change in memory:
Flash: -12 bytes
SRAM: 0 bytes
This prevents the ability to run gcode from the SD card.
In a thermal error with faulty values, and without serial access, this
is the only way to process an M310 instruction and recover.
It's only used when MESH_BED_LEVELING is not defined. According to
the configuration files, all printers supported use MESH_BED_LEVELING.
So I think we are safe in removing this dead code.
The firmware saves the current fanspeed before parking,
and the fanspeed is restored after unparking. The problem is the fan
was never actually paused.
Fixes#3670
This code was introduced with v3.8.0 but was always disabled.
I propose the code be removed since it has not been enabled
for 3 years since its introduction.
- Work-around SOURCE flags being reset for each project when setting the
random-seed property by calling a support function.
- Likewise, set correct flags for reproducibility when creating archives.
- Strip source prefix paths from debug info
This should set the EPOCH using the last git commit date when available,
but it's not currently implemented. Just set the EPOCH to be 0 for now.
We want to move the Z-axis after the XY move is done.
raise_z cannot be used here because it relies
on current_position[] for all axis.
It is actually 10 bytes cheaper to use the previous method
because syncing current_position with lastpos is surprisingly expensive
Don't render full screen for Loading Filament X
this is already done in load_filament_to_nozzle
so no need to do it twice
Change in memory:
Flash: -54 bytes
SRAM: 0 bytes
This fixes an issue where the assumed slot to use is unknown and
the printer will hang on loading filament 100.
Another good thing is this is an old user feature request which
we have in our 3.12 milestone.
Change in memory:
Flash: +14 bytes
SRAM: -1 bytes
If the endstops kick in, then st_get_position_mm shows the actual travel distance. current_position[Z-AXIS] does not get updated correctly thus we cannot use it when unhomed.
current_position[Z-AXIS] is later set to Z_MAX_POS,
we cannot use that either to calculate the travel distance
Removed the "plan" parameter.
We were incorrectly returning from the function if the printer was homed,
but plan = false. This would leave current_position with an incorrect value
If the printer is homed => finish the move and return the travel distance
If the printer is not homed => rely on end stop to prevent damage,
return travel distance even if the endstop stopped the move.
* Created a new function raise_z() which will move the Z axis by some
X millimeters. If plan = false, the function will return the
actual travel distance since the move is blocking.
* raise_z_above() is refactored to call raise_z()
Now the M701 and M702 will move the Z-axis relatively, and also
when done, revert the Z axis position when done.
This is a similar behavior as in Marlin 2.
It is only used when the MMU is disabled. With the MMU we use a defined ramming sequence.
When the MMU is disabled I borrowed the usages from Marlin 2.
The L parameter only defines the length for the "fast" load length.
Default value is 70mm, same as M600
Fix the unload procedure when the user has paused a print
then stopped the print after the temperature has reached below 175°C
Now the E-motor will move as expected
The following situation is now fixed, steps:
1. Load filament through LCD
2. Load to nozzle through LCD
3. Before filament reaches Fsensor => turn off the printer
4. Wait a few seconds and then turn the printer on again
5. Start a print through the SD card
6. Printer will unload and then re-load the filament
Previously in step 6, the printer would start a print without any
filament loaded.
Guðni Már Gilbert
Yuri D'Elia
Alex Voinea
Alex Voinea
3d-gussner
D.R.racer
DRracer
Yuri D'Elia
VintagePC