bb0bbfb45f
PFW-1386 Minor correction to M707 and M708 useage example
2022-09-16 10:22:39 +02:00
d78c575399
PFW-1386 Address should accept hexidecimal values
...
Now these are equal:
M707 A255 C1
M707 A0xFF C1
Both address inputs are interpreted as FF
2022-09-16 10:22:39 +02:00
ba7dae5c79
PFW-1386 I don't see a reason for these lines
...
So I'm removing them
2022-09-16 10:22:39 +02:00
3192a95e78
PFW-1386 Optimise default value assign z_target
2022-09-16 10:22:39 +02:00
20c865c2d4
PFW-1386 Implement 'U' parameter for M702
...
Similar to 'L' in M701, this does not apply to the MMU
The U parameter controls how much mm the extruder will unload
Default value is 80mm
2022-09-16 10:22:39 +02:00
7e9166976f
PFW-1386 Implement 'L' parameter for M701
...
It is only used when the MMU is disabled. With the MMU we use a defined ramming sequence.
When the MMU is disabled I borrowed the usages from Marlin 2.
The L parameter only defines the length for the "fast" load length.
Default value is 70mm, same as M600
2022-09-16 10:22:39 +02:00
94dd4aec73
PFW-1386 M701 now loads to nozzle with MMU
2022-09-16 10:22:39 +02:00
8462b38446
PFW-1386 Create a common function for M704 to M706
...
Saves 36 bytes of flash
2022-09-16 10:22:38 +02:00
d6564d3617
PFW-1386 if automatic = false, raising Z-axis is done via gcode
2022-09-16 10:22:38 +02:00
32ec1587b9
PFW-1386 Implement changes to M702
2022-09-16 10:22:38 +02:00
9b0d89213b
PFW-1386 Raising Z-axis during M701 is now done via Gcode
...
If the Z-parameter is not issued, then default behavior will raise
the Z-axis by MIN_Z_FOR_LOAD
2022-09-16 10:22:38 +02:00
5bb36546b4
PFW-1386 Implement changes to M701
2022-09-16 10:22:38 +02:00
fb087fc535
PFW-1386 Add M707 and M708
...
WriteRegister and ReadRegister function will create new compiler
warnings due to unused parameters, we can ignore it for now.
2022-09-16 10:22:38 +02:00
3664d29b21
PFW-1386 Add M709
2022-09-16 10:22:38 +02:00
de0539b630
PFW-1386 Implement M704, M705, and M706
2022-09-16 10:22:38 +02:00
70532333dc
Optimize filament sensor implementation
...
- remove virtual methods (we only have one fsensor implementation at a time)
- comment out some of the debugging texts
- remove volatile and replace them with proper synchronized access to relevant variables
2022-09-16 10:22:38 +02:00
2662e09f1e
Another message remove from RAM
2022-09-16 10:22:38 +02:00
0e036b9d8a
Save some more RAM in protocol_logic
2022-09-16 10:22:38 +02:00
022aa53b2d
Remove active_extruder completely
...
we only use 1 extruder + saves ~800B
2022-09-16 10:22:38 +02:00
0889109760
Fix corrupted chars in "Engaging Idler" message
2022-09-16 10:22:38 +02:00
bac3168ca4
Optimise power_on and power_off
...
eeprom_update_byte only updates the EEPROM if the value is different
Saves 40 bytes of flash memory
2022-09-16 10:22:38 +02:00
0d64cfa2e5
extruder variable should be one byte
...
Saves 1 byte of SRAM and 132 bytes of flash
2022-09-16 10:22:38 +02:00
87a4f58e66
PFW-1363 Change MMU Error parking position
2022-09-16 10:22:38 +02:00
703c463a49
Optimize unload
...
Toolchange during print is now much quieter.
Excessive E-motor movement during print is now gone
2022-09-16 10:22:38 +02:00
47e57646ea
Optimize load
...
Don't start moving the E-motor immediately
Instead of starting the E-motor move when the load to extruder starts,
we can start when we are loading to the fsensor. At that stage
the MMU has changed from a fast load to a slow load.
2022-09-16 10:22:38 +02:00
2f0ceabce5
Upgrade protocol to v2.1 - read/write registers + CRC
2022-09-16 10:22:38 +02:00
f18721bee3
Fix unintentional typo
2022-09-16 10:22:38 +02:00
6d6f9583ea
Initialize retryAttempts in constructor
2022-09-16 10:22:38 +02:00
485ed4a213
Fix issue where logs show two corrupted chars
...
Issue only appears when LANG_MODE = 1
2022-09-16 10:22:38 +02:00
938fac4058
Remove old comment, button is acknowledged now
2022-09-16 10:22:38 +02:00
f717aa161c
Remove TODO in ActivatePlannedRequest
2022-09-16 10:22:38 +02:00
b9d9308f9f
Support 3x Retry in Idle state machine
2022-09-16 10:22:38 +02:00
ab32769487
Send button from current state machine
2022-09-16 10:22:38 +02:00
4f30cf0ba3
Add missing ProtocolError
2022-09-16 10:22:38 +02:00
bc85a41059
Fix xflash flashing
2022-09-16 10:22:38 +02:00
53e2d68183
Retry up to 6x in case of incorrect MMU FW version
...
Because it looks like the communication drop outs are caused by some electrical issues and we can loose even a byte from the version response, which is deadly for future operation.
2022-09-16 10:22:38 +02:00
6e5fcb5838
Tune a few MMU progress codes' texts to fit on the LCD
2022-09-16 10:22:38 +02:00
14b2befb7d
Switch from Start Seq into Idle immediately + disable FS autoload on MMU
2022-09-16 10:22:38 +02:00
400fec5d9f
Reset CustomMsg when Command in progress is None
...
When a Progress report is started, we set the CustomMsg to MMUProgress.
But there was an issue where, once the reported "Progress" action was done.
We did not reset the CustomMsg to Status. So if we are printing from the
SD card, the file name is not displayed on the LCD.
2022-09-16 10:22:38 +02:00
5b184d885c
Add LCD_BUTTON_TIMEOUT to enum
2022-09-16 10:22:38 +02:00
e59651a279
Remove description in header file
...
The description are more detailed in the ultralcd.cpp file
No need to document the function in two places :)
2022-09-16 10:22:38 +02:00
2fc8b50f11
Fix lcd_show_multiscreen_message_yes_no_and_wait_P after rebase
2022-09-16 10:22:38 +02:00
be3f9376ba
Add missing break
2022-09-16 10:22:38 +02:00
09cb9c6ecd
Fixup after rebase + discussion
2022-09-16 10:22:38 +02:00
1d2acb5bd6
Bump MMU FW version to 2.0.19 to match/enforce the necessary compatibility level
2022-09-16 10:22:38 +02:00
fa176c69db
Fix protocol error recovery
...
Communication timeout and Protocol Errors are now distinguished.
In case of a Protocol Error, the printer waits for heartBeatTimeout to allow filling up the input UART buffer (we expect the MMU still produces some bytes).
Once the timeout elapsed, the input UART buffer is cleared and a new Start Sequence is initiated.
2022-09-16 10:22:38 +02:00
6bf2aebf04
Fix typo
2022-09-16 10:22:38 +02:00
80c640deb9
PFW-1373
...
Fix the unload procedure when the user has paused a print
then stopped the print after the temperature has reached below 175°C
Now the E-motor will move as expected
2022-09-16 10:22:38 +02:00
ba52430e1d
Magic numbers are bad...
2022-09-16 10:22:38 +02:00
69c39e2281
An attempt at fixing the retry. Discussion needed.
2022-09-16 10:22:38 +02:00
Guðni Már Gilbert
D.R.racer
Alex Voinea
VintagePC