80cb13003e
Show filename after SD print finished
2024-12-30 13:57:58 +01:00
901f63e90f
remove incomplete dual stepper configuration
...
If either Y_DUAL_STEPPER_DRIVERS or Z_DUAL_STEPPER_DRIVERS is defined
the compilation will fail with an error message. This configuration will likely
never be fully implemented unless someone from the community steps up.
2024-12-30 13:57:08 +01:00
3ea620c27a
Eject translations in German and Dutch not shorten as it fits now the multiple choice.
2024-12-24 07:52:50 +01:00
a704b99d81
Fix multiple choice
...
Fixes #4819
2024-12-24 07:52:50 +01:00
d3f95592c1
Convert uart2.c to a C++ file
2024-11-27 09:16:41 +01:00
6b01929382
Trim empty lines
2024-11-27 09:16:41 +01:00
4a0973941f
Mark uart2_putchar and uart2_getchar as static
2024-11-27 09:16:41 +01:00
51e81217dd
Remove unhelpful comments and constants
2024-11-27 09:16:41 +01:00
18bda84876
remove unused function uart2_rx_str_P
2024-11-27 09:16:41 +01:00
b67554eb01
Switch back from `%g` to `.4f`
...
Set short length so the square is printed in the middle of the bed
Both purge lines with and without MMU end at X=202.5 to get the square in the middle of the bed
2024-11-20 12:10:33 +01:00
7a47bf30be
Fix end of meander overextrusion with new pattern
2024-11-20 09:28:21 +01:00
24ce71eded
Optimize meander moves
2024-11-20 09:11:18 +01:00
519724b53d
Ensure all meander moves are done using relative mode
...
Without this the first vertical move of the new meander would be slightly longer than expected due to using absolute moves from a negative Y starting position
2024-11-20 08:57:36 +01:00
81d124affd
Minor nitpicks
2024-11-20 08:52:12 +01:00
13d12c0ffa
Get rid of float casts
2024-11-20 08:38:19 +01:00
e84ade3542
optimisation: combine a few functions calls into one
...
Change in memory:
Flash: -34 bytes
SRAM: 0 bytes
2024-11-19 19:50:12 +01:00
658df9d04d
Extract G91 to messages.h/cpp
2024-11-18 10:12:05 +01:00
1319af8a12
Ensure that a correct feedrate is used at all times
2024-11-18 10:09:10 +01:00
44f9b953c5
remove unused step parameter in lay1cal sqaure
2024-11-18 09:51:02 +01:00
0b5afa3092
Unload the filament at parked position
...
We don't want to unload while the nozzle is still smudged against the bed.
2024-11-18 09:45:51 +01:00
a0278b2844
Fix an issue where MMU unloads filament while its cooling down
...
Change in memory:
Flash: -6 bytes
SRAM: 0 bytes
2024-11-18 09:45:51 +01:00
d1470d8abc
New first layer calibration
...
- changed to relative mode to save buffer and code size
- added NEW_FIRST_LAYER_CAL to perform 1st layer cal from front to back
2024-11-14 14:45:25 +01:00
d8d058a63b
Add Set parameter in M78 Statistics gcode ( #4809 )
...
* Add Set Statistics
* EEPROM_FILAMENTUSED is in centimeter and not meter
Fix few things
* Fix typo
2024-11-14 08:20:39 +01:00
cdb6635eac
Remove hardcoded MMU tool count
...
- Preload to MMU -> All
- Loading Test -> All
- SpoolJoin
2024-10-29 15:50:01 +01:00
f12683f3ff
Further relax the MBL tight threshold
2024-09-24 10:33:23 +02:00
402b9ed93a
Add `#ifdef FANCHECK` thanks @gudnimg
2024-09-23 07:00:17 +02:00
65a26e882b
Enable Tune menu during fan check issues, user can then disable the fan check if needed.
...
Send //action:cancel when LCD Stop print is selected.
2024-09-18 16:09:46 +02:00
29c920c801
Fix MMU unload issue after a fan check issue has been solved
2024-09-18 16:09:46 +02:00
de092b35d5
PFW-1562 Fix an issue where safety timer is not handled correctly in mFilamentPrompt menu
2024-09-15 10:28:10 +00:00
7d3032c001
Bump up version to FW3.14.1-RC1-8225
2024-09-04 09:33:47 +02:00
6ea47967da
Merge pull request #4765 from leptun/MBL_fixes
...
Region MBL fixes
2024-09-04 07:42:48 +02:00
4e9e20c67f
Merge pull request #4766 from gudnimg/remove-sm4_line_xyze_ui
...
Remove sm4 line xyze UI
2024-09-03 15:22:56 +02:00
3facdb4576
Add new message and translations
2024-09-03 09:34:18 +02:00
b614b9c43d
Do not prompt for steel sheet on bed during XYZ calibration
...
Thanks @3d-gussner
2024-09-03 09:28:16 +02:00
b58d2ecccb
Prompt user for Z calibration after failed MBL with yes-no screen
2024-09-03 09:28:15 +02:00
357b68cf76
Ask for steel sheet on bed during Z calibration
2024-09-03 09:28:15 +02:00
d2119c24e1
Prompt Z calibration when 7x7 MBL is enabled
2024-09-03 09:28:15 +02:00
8196e48684
Reduce number of Z realignments before Z calibration is requested
2024-09-03 09:28:15 +02:00
d8e3c2b481
Relax 3x3 MBL threshold
2024-09-03 09:28:15 +02:00
b3a682d330
Always re-init the TMC drivers after leaving linearity correction menu
...
Change in memory:
Flash: -22 bytes
SRAM: 0 bytes
2024-09-01 22:14:25 +00:00
312f79c5f5
optimisation: Simplify saving linearity correction
...
Keep in mind that the EEPROM addresses are in descending order. This means we
can't use eeprom_read_block() or eeprom_update_block()
Address --> Axis
3831 --> X-axis
3830 --> Y-axis
3829 --> Z-axis
3828 --> E-axis
Change in memory:
Flash: -118 bytes
SRAM: 0 bytes
2024-09-01 12:34:00 +00:00
aa8569600c
Fix build and make sm4 a C++ file
2024-09-01 12:12:24 +00:00
a2d45e5d11
cleanup: remove unused global sm4_cpu_time
2024-09-01 12:11:56 +00:00
f115adf894
cleanup: remove unused function sm4_get_dir
2024-09-01 12:11:56 +00:00
5a5c68f563
cleanup: remove unused function sm4_get_dir_bits
2024-09-01 12:11:56 +00:00
7d3c416d04
cleanup: remove unused function sm4_line_xyze_ui
...
No change in code size. Reason for removing this function
is just to reduce lines of code that is maintained.
2024-09-01 12:11:22 +00:00
6c99a4463e
Merge pull request #4755 from sarusani/AddLoadIfAutoloadDisabled
...
Add "load filament" if autoload is disabled
2024-08-30 17:11:37 +02:00
a259482b6b
Add load option if autoload is disabled
2024-08-30 14:48:45 +02:00
923f926223
Merge pull request #4749 from gudnimg/remove-auto-bed-leveling
...
Remove legacy Auto Bed Leveling code
2024-08-30 10:44:50 +02:00
b353f1f008
Add missing translations
...
Used `trans -b :cs+de+es+fr+hr+hu+it+nl+no+pl+ro+sk+sv "<text>"` to translate
Looked at pre-translated text to reuse as much as possible.
2024-08-26 10:02:56 +02:00
3d-gussner
gudnimg
Alexandra Voinea
sarusani