bc27b71729
Pull one common G1 gcode into PROGMEM
...
Change in memory:
Flash: -32 bytes
SRAM: 0 bytes
2023-03-18 17:37:27 +00:00
f296b3f826
G21 is not implemented, don't queue it
...
It's just a single 'break', will likely not be implemented
Change in memory:
Flash: -6 bytes
SRAM: 0 bytes
2023-03-18 17:23:01 +00:00
6edd8b0719
Add M220 into PROGMEM
...
Change in memory:
Flash: -10 bytes
SRAM: 0 bytes
2023-03-18 17:09:43 +00:00
00515a975d
Add M107 into PROGMEM
...
Change in memory:
Flash: -4 bytes
SRAM: 0 bytes
2023-03-18 17:05:35 +00:00
5ade1716bf
Add M500 into PROGMEM
...
Change in memory:
Flash: -6 bytes
SRAM: 0 bytes
2023-03-18 17:01:59 +00:00
733bc874fb
Move G28W0 to messages
...
No change in memory
2023-03-18 16:48:30 +00:00
466a6a8fc3
Add M600 into PROGMEM
...
Change in memory:
Flash: -10 bytes
SRAM: 0 bytes
2023-03-18 16:33:13 +00:00
129cc18cbf
Add M23 %s into PROGMEM
...
Change in memory:
Flash: -14 bytes
SRAM: 0 bytes
2023-03-18 16:18:05 +00:00
7c0ead7bc2
Add M24 into PROGMEM
...
Change in memory:
Flash: -8 bytes
SRAM: 0 bytes
2023-03-18 16:15:10 +00:00
5f8fc64a32
Restore previous Z-lift in M701/M702
...
Previously when the firmware called M701/M702 manually
there was no Z lift. But after we added support for the Z
parameter we set the default to 50mm.
Change strings "M701" to "M701 Z0" and "M702" to "M702 Z0"
to restore the previous behavior from before 3.13.
Also pulled the gcodes into PROGMEM in message.cpp
along with M83 and M84 to save memory.
Change in memory:
Flash: -34 bytes
SRAM: 0 bytes
2023-03-18 15:34:47 +00:00
c3235386a1
Bump up commit number
2023-03-15 07:52:01 +01:00
8b49d241d2
revert BTN_MORE non-translated
2023-03-15 07:03:41 +01:00
00309f42c3
Bump up fw version
...
6508 from t3.13.0-BETA1
+50 commits
+1 for this commit
+1 for merge
2023-03-14 15:18:13 +01:00
3fe2f25c9f
Disable reading MMU register 0x21
...
It has proven to be too unreliable and may confuse end users.
2023-03-14 15:12:50 +01:00
68b4a8a6cb
Last minute changes need a revert of the fw bump up
2023-03-14 11:22:43 +01:00
e87e1630e2
Bump up version
...
t3.13.0-BETA1 commit nr 6508
+46 commits between
+1 commit for this PR
+1 commit for the merge
=6556
2023-03-14 09:09:38 +01:00
e951a106d6
Messages fit to pages
2023-03-14 08:56:46 +01:00
8604c93ccc
Shorten messages as users will contact support anyway
2023-03-14 08:32:16 +01:00
616cf61583
Revert
2023-03-14 08:31:21 +01:00
22e70faa71
Remove `MMU2` and `MMU unit` messages
...
Saves 26byte of flash
Saves -368 byte in trasnlations
2023-03-14 08:30:15 +01:00
7676df88a4
Rename forgotten `MMU2` message to `MMU`
2023-03-14 08:30:03 +01:00
235c4ae943
Do not `MSG_BTN_MORE` translate
2023-03-14 08:26:39 +01:00
9721a87ef2
Raname `MMU2` message to `MMU` as everywhere
2023-03-14 08:24:50 +01:00
03778226ca
Remove `Select Extruder:` message
...
Post fix PR4064 for update.po*.py scripts
2023-03-14 08:24:12 +01:00
93598ef00d
Change some messages to be max three rows instead of two
...
Yes|No are now located at the 4th row and so messages can
use three rows. This should allow improvement in some translations.
2023-03-14 08:23:40 +01:00
ebf94c572f
PFW-1504 Minor optimisation
...
Change in memory:
Flash: -4 bytes
SRAM: 0 bytes
2023-03-13 06:47:08 +01:00
42878341af
PFW-1504 More correct solution to the pixel count issue
...
The fact that the relationship between
machine position and pixel index is not linear
means we cannot simply rely on comparing
the previous position to the next machine position. i.e derivative of E_AXIS
Because around the max amplitude of the triangle wave
the slope will suddenly change sign and will create a deadzone
which has width 2*mm_per_pixel.
For MMU2S this is ~10mm (or two pixels).
Instead we should split the moves.
And only plan the 2nd move once we're
at the top of the triangle wave. That way we don't really care about the position delta.
Now we just calculate the current y(x)
position relative to current position and divide by mm_per_pixel.
If there is a delta measured with unit 'pixel' then that means
its time to render the next pixel.
This solution seems to work well so far on my end.
Change in memory:
Flash: +2 bytes
SRAM: 0 bytes
2023-03-13 06:47:08 +01:00
b5e323e67c
PFW-1504 rename length_step_mm to mm_per_pixel
...
Its more descriptive
2023-03-13 06:47:08 +01:00
9865d4a38a
PFW-1504 Add precision error
...
This fixes an issue where sometimes
not all 20 pixels are rendered.
It is better to render 1 too many pixels (sometimes), rather than rendering too few.
Change in memory:
Flash: +18 bytes
SRAM: 0 bytes
2023-03-13 06:47:08 +01:00
f2157c6f1d
Fixup
...
We're always setting the cursor position when rendering now
Saves 8 bytes of flash
2023-03-13 06:47:08 +01:00
c518bfdb73
PFW-1504 Set cursor position each time to be safe
...
Change in memory:
Flash: +18 bytes
SRAM: 0 bytes
2023-03-13 06:47:08 +01:00
59e1ac0396
PFW-1504 implement stepper_get_machine_position_E_mm()
...
This function should be used when reading the current machine
position while a move is ongoing
No change in memory
2023-03-13 06:47:08 +01:00
690d83a94a
fixup
2023-03-13 06:47:08 +01:00
9145c8f59f
PFW-1504 too much?
...
I'm not happy with the current solution, I think we can improve it
by using the fact that this is a triangle wave. Need to think about it.
2023-03-13 06:47:08 +01:00
73c76579af
PFW-1504 Add init for progress bar
...
In case we are running a retry, the firmware
should clear the old rendering before
starting on a new one
Change in memory:
Flash: +6 bytes
SRAM: 0 bytes
2023-03-13 06:47:08 +01:00
51f1aa14a5
PFW-1504 Update last position as quickly as possible
...
0.1mm extrusion may happen while updating the LCD
No change in memory
2023-03-13 06:47:08 +01:00
bbfc4b9f78
PFW-1504 initial commit
...
Change in memory:
Flash: +162 bytes
SRAM: 0 bytes
2023-03-13 06:47:08 +01:00
04d440a9c8
Fix AutoLoad filament menu not shown when FSensor is [Off] ( #4072 )
...
Fix AutoLoad filament menu not shown when FSensor if [Off]
2023-03-10 14:23:56 +01:00
ba41b2bb0b
Fix M706 lcd message stuck
2023-03-09 07:00:40 +01:00
e787111922
Add MMU error code: MCU_UNDERVOLTAGE_VCC ( #4069 )
...
+ read bandgap voltage periodically
+ correct wording of ERR_ELECTRICAL_MCU_UNDERVOLTAGE_VCC (as requested in Prusa-Error-Codes PR#81)
2023-03-08 15:42:25 +01:00
a20a7232a8
Change "Extruder N" to "Filament N"
...
Change in memory:
Flash: -52 bytes
SRAM: 0 bytes
2023-03-06 10:26:12 +01:00
03280c48d5
Merge pull request #4059 from gudnimg/planner-opt-subtraction
...
planner: calculate step difference once
2023-03-03 14:42:47 +01:00
474d489c39
Merge pull request #4033 from gudnimg/improve-preheat-target
...
preheat: improve target temperature threshold
2023-03-03 14:41:58 +01:00
bc818636b0
Increase MMU FW version to 2.1.8
...
in relation to MMU-218
2023-03-02 19:58:00 +01:00
d487254806
planner: calculate step difference once
...
Change in memory:
Flash:-158 bytes
SRAM: 0 bytes
2023-03-01 22:28:08 +00:00
051054b0db
Bump up FW version and build number
2023-02-24 16:42:36 +01:00
303a67cd6f
Introduce MMU EEPROM reset feature
...
This new feature requires MMU FW v 2.1.7 (which brings some more small changes)
2023-02-24 15:26:07 +01:00
31bfbb4ed0
Merge pull request #4023 from DRracer/rename-eject-mmu
...
PFW-1497 Change Eject filament -> Eject from MMU
2023-02-23 10:48:35 +01:00
afc866e756
Merge pull request #4010 from gudnimg/improve-backlight-control
...
backlight: always allow backlight to dim/wake
2023-02-21 10:00:03 +01:00
8a926fad10
backlight: set rotation flag when certain amount of pulses are detected
...
We don't want to trigger a backlight wakeup randomly, for example
due to background noise.
2023-02-20 18:26:43 +00:00
Guðni Már Gilbert
3d-gussner
D.R.racer
DRracer