-[X] Bumped up build number to 7080 (pre build was 7078 + 1 commit + 1 merge)
-[X] Updated .pot and .po files code lines using `update-pot.py` and `update-po.py --all`
-[X] Verifed pot and po files changes
While waiting for the nozzle to reach a certain temperature, a fan error
should disable the hotend heater. If printing, it will simply pause the print.
Previously the printer would wait for the nozzle to heat up before pausing the print
and turning off the hotend heater.
We rely on LcdCommands::LongPause and must return to the top level loop to process it.
Waiting in the while loop e.g. in M190 does not make sense.
lcd_calibration_menu: Remove redundant if (!isPrintPaused). The menu
is never called unless this condition is true.
eeprom_switch_to_next_sheet: Don't show this menu if the printer
is busy doing work!
Do not allow these menus to run while a print is paused or
when we're recovering a print:
- Preload to MMU
- Load to Nozzle
- Unload filament
- Eject from MMU
- Cut filament
- Autoload filament
- Settings
- Calibration
There is a bug where if the printer is recovering a print, it run a
blocking loop to restore the extruder and bed temperatures.
But if a Fan error is triggered in this loop, then the user can't
abort the print via LCD.
If the fan error resolves on its own the 'Resume print' menu will
appear in a few seconds. But if not, then the user can't resume the print
(which is normal). But with the bug above the user can't abort the print either!
The problem is essentially isPrintPaused variable is cleared too early.
We should wait until the print is completely restored first.
Steps to reproduce:
1. Start a print
2. Pause the print
3. Wait for extruder temperature to fall at lest 180°C
4. Click 'Resume' print
5. While heating, stop the hotend fan and wait for a few seconds until an error is raised
6. Observe issue => 'Stop print' menu item is gone!
PFW-1542
This fixes the undefined _T(label) reference, at the expense of a few
extra bytes.
I would argue this is worth the cost for the ability to check
translation references for the future. The warning happens because
`lang-check` cannot check a reference which is not _directly_ a catalog
entry.
We could introduce a method to suppress this warning (either a new macro
or some ///IGNORE comment), but that would mean that the additional
translation check is completely bypassed, defeating the purpose.
We can't clear eFilamentAction in every case in mFilamentItem()
mFilamentItem() can trigger a call to M701 and M702 e.g. for Autoloading
and eFilamentAction must be cleared by the gcode to prevent
the user from triggering another Autoload (which will crashe the FW)
The same applies to submenus. Now the MMU submenus clear eFilamentAction
only when the action is done.
For MMU Unload Filament item, eFilamentAction is only cleared after
the unload_filament() call is done running. This fixes an issue where
the menu item can be selected again while the first unload is still
running.
Allow to set the source epoch of the build with
PROJECT_VERSION_TIMESTAMP.
When unset fetch the commit timestamp of the current HEAD automatically
instead of leaving the source as 0. This fixes the firmware DATE
information in the support menu.
If for some reason a user added a extrusion move in the firmware. Prevent FINDA runout
from triggering.
Change in memory:
Flash: +16 bytes
SRAM: 0 bytes
temp_compensation_start() is only called when
PINDA_THERMISTOR is not defined.
Additionally make sure the retraction or unretraction cannot happen
twice in case MBL fails.
For MK3S users with MMU this extrusion move could
cause a FINDA runout event.
Change in memory:
Flash: -130 bytes
SRAM: 0 bytes
An example is when Unloading filament with MMU.
After the unload completes successfully, some menu items disappeared.
Because mFilamentBack() was not called
Change in memory:
Flash: -56 bytes
SRAM: 0 bytes
Kudos to @3d-gussner for finding the issue
Steps to reproduce:
1. reset printer
2. select Load filament
3. go back to main
4. LCD menu is very limited
5. To get all menus back select 6. Preheat
7. back to main
This commit is my proposed fix.
When eFilamentAction is equal to
FilamentAction::Load we must reset it to FilamentAction::None
when the Back button in Load Filament is selected
Change in memory:
Flash: -26 bytes
SRAM: 0 bytes
3d-gussner
gudnimg
D.R.racer
Yuri D'Elia
vintagepc
sarusani