52ac95f082
Merge pull request #4600 from sarusani/ChangeRevoNozzleChangeMenu
...
Adjust Nozzle Change Menu For Quick Change Nozzles
2024-04-11 19:19:01 +02:00
bc04f16906
Adjust Nozzle Change Menu For Quick Change Nozzles
...
- Show warning if extruder temp is > 40 degrees
- Use fan to speed up cooldown
- Show confirmation msg
- Show nozzle diameter setting after nozzle change
2024-04-09 16:12:46 +02:00
bd935db31e
Add Eject Option To Filament Load Message
2024-04-09 15:50:17 +02:00
a93cd93756
Move `MK3 firmware detected on MK3S printer` and `MK3S firmware detected on MK3 printer` to `messages.cpp/.h`
...
Update pot and po files
2024-04-04 08:58:46 +02:00
97584d571e
Update all `_i("` to `messages.cpp/.h`
...
Update `lang/po/*.po*` files
2024-04-04 08:23:40 +02:00
52ba1b534d
Add HOST power panic auto recovery option
...
Change `PRINT_TYPE_USB` to `PRINT_TYPE_HOST`
Fix more rebase issues
Fix rebase issue again
2024-01-29 13:07:48 +01:00
c9aba688e3
Saving few bytes by removing spaces in `//action:` host commands. Thanks to @sarusani pointing out inconsistent documentation.
...
Renaming `MSG_OCTOPRINT_*` to `MSG_HOST_ACTION_*` as it is used also with PrusaLink and other host printing solutions
Fix rebase issues
2024-01-29 13:07:48 +01:00
59093107fd
Add #ifdef HOST_SHUTDOWN
2024-01-06 00:45:06 +01:00
49f9d7abdc
Add Shutdown host to LCD Menu
...
Add "Shutdown host" entry to LCD menu if printer is not active and host is connected.
2024-01-06 00:45:06 +01:00
18daa5a62e
Merge pull request #2423 from Panayiotis-git/MK3_M600_Issue-2415
...
LCD option to unload new filament on M600 (issue #2415 )
2023-12-04 17:03:38 +01:00
e2aafc882c
Fix MSG_PRINT_PAUSED
...
MSG_PRINT_PAUSED used the lang declaration MSG_PAUSE_PRINT instead of MSG_PRINT_PAUSED
2023-12-03 10:16:16 +01:00
3da4407e4f
Repeat the M600 unload/load filament sequence - Fix translations
2023-12-01 21:13:24 +02:00
4d9dc11510
power panic: pause the print, and wait for M79
...
"PRUSA uvlo" is the last g-code to be processed after the power panic
recovery. For host prints, we want to finish processing all these
g-codes and put the print in a paused state.
Currently I am using lcd_pause_print() but this may be simplified
later.
A new PrinterState is introduced PowerPanicWaitingForHost to
differentiate this paused state from the typical paused state.
In this new paused state the printer is waiting for the host to boot up
and send M79.
Once M79 is seen a new action is sent "// action:uvlo_recovery_ready"
It is up to the host software to then resume the print correctly. All
the needed information to resume the print is in EEPROM and can
be read by using the D3 g-code.
Change in memory:
Flash: +82 bytes
SRAM: 0 bytes
2023-12-01 16:16:39 +01:00
096a1c9fe0
Change Reprint action message to comply to OctoPrint actions
2023-11-30 15:08:48 +01:00
7130504fcf
Apply the reprint_pr_changes_diff2.txt provided by @3d-gussner
2023-11-22 12:18:59 +01:00
532a5b3e2f
- Serial message --> /// action:reprint done
...
- Yes/no question --> Need to fix the bug related with the filename print --> if (lcd_show_fullscreen_message_yes_no_and_wait_P(altfilename, false, LCD_LEFT_BUTTON_CHOICE)==LCD_LEFT_BUTTON_CHOICE)
2023-11-22 12:14:00 +01:00
e8a2d4c7e1
Reprint function integrated on 3.13v
2023-11-22 12:11:39 +01:00
880d2f28bd
LCD menu only sends `// action:ready` or `// action:not_ready` via serial
...
Host has to send back state with `M72 S1|0` to keep printer and host in sync
Changed LCD menu messages to `Set ready` and `Set not ready`
Updated translations
2023-11-22 07:58:17 +01:00
d276695ce7
Set Ready
2023-11-22 07:58:13 +01:00
45880c252b
Fix filament change behavior when print is paused
...
Reimplementing PR 2390
https://github.com/prusa3d/Prusa-Firmware/pull/2390
from @wavexx
2023-11-11 16:51:35 +00:00
1c637f8082
Fix " 🔃 Refresh" translation
2023-10-03 08:19:48 +02:00
47775e158b
Reuse messages
2023-08-21 19:00:22 +02:00
0bbec5626c
Update and fix translations
2023-08-21 16:28:36 +02:00
44ae8033eb
Rename upper case `TEMP_MODEL` to `THERMAL_MODEL`
2023-07-25 17:13:07 +02:00
f43451f80b
Update `MSG_EJECT_FILAMENT` and `MSG_CUT_FILAMENT` to `c=16`
...
Had to shorten SK translation
2023-05-23 09:50:27 +02:00
a37bcbfd8c
Fix `Load filament` to c=16
2023-05-23 09:45:07 +02:00
9d5453a41e
PFW-1520 Rename Load Filament menu to Preload to MMU
...
Change in memory:
Flash: +18 bytes
SRAM: 0 bytes
2023-05-22 07:53:26 +02:00
26369ac540
Restore old M701/M702 behavior
...
If the new Z parameter is not given,
assume that the old Z-lift behavior is desired.
Change in memory:
Flash: -28 bytes
SRAM: 0 bytes
2023-04-29 16:22:28 +00:00
7f921b4071
Limit some of the float formatting to fit 30 bytes buffer in enquecommandf_P
2023-04-05 09:10:39 +02:00
7e0bf88431
Use `G28 W` only
2023-03-22 12:30:16 +01:00
bc27b71729
Pull one common G1 gcode into PROGMEM
...
Change in memory:
Flash: -32 bytes
SRAM: 0 bytes
2023-03-18 17:37:27 +00:00
6edd8b0719
Add M220 into PROGMEM
...
Change in memory:
Flash: -10 bytes
SRAM: 0 bytes
2023-03-18 17:09:43 +00:00
00515a975d
Add M107 into PROGMEM
...
Change in memory:
Flash: -4 bytes
SRAM: 0 bytes
2023-03-18 17:05:35 +00:00
5ade1716bf
Add M500 into PROGMEM
...
Change in memory:
Flash: -6 bytes
SRAM: 0 bytes
2023-03-18 17:01:59 +00:00
733bc874fb
Move G28W0 to messages
...
No change in memory
2023-03-18 16:48:30 +00:00
466a6a8fc3
Add M600 into PROGMEM
...
Change in memory:
Flash: -10 bytes
SRAM: 0 bytes
2023-03-18 16:33:13 +00:00
129cc18cbf
Add M23 %s into PROGMEM
...
Change in memory:
Flash: -14 bytes
SRAM: 0 bytes
2023-03-18 16:18:05 +00:00
7c0ead7bc2
Add M24 into PROGMEM
...
Change in memory:
Flash: -8 bytes
SRAM: 0 bytes
2023-03-18 16:15:10 +00:00
5f8fc64a32
Restore previous Z-lift in M701/M702
...
Previously when the firmware called M701/M702 manually
there was no Z lift. But after we added support for the Z
parameter we set the default to 50mm.
Change strings "M701" to "M701 Z0" and "M702" to "M702 Z0"
to restore the previous behavior from before 3.13.
Also pulled the gcodes into PROGMEM in message.cpp
along with M83 and M84 to save memory.
Change in memory:
Flash: -34 bytes
SRAM: 0 bytes
2023-03-18 15:34:47 +00:00
e951a106d6
Messages fit to pages
2023-03-14 08:56:46 +01:00
03778226ca
Remove `Select Extruder:` message
...
Post fix PR4064 for update.po*.py scripts
2023-03-14 08:24:12 +01:00
93598ef00d
Change some messages to be max three rows instead of two
...
Yes|No are now located at the 4th row and so messages can
use three rows. This should allow improvement in some translations.
2023-03-14 08:23:40 +01:00
5cd60636f9
Add missing translations + shorten to 16 chars
2023-02-18 17:39:30 +01:00
98e7c15928
Change Eject filament -> Eject from MMU
...
PFW-1497
2023-02-18 17:39:30 +01:00
05662a5c0a
optimsation: reduce code size in LCD rendering
...
Change in memory (MK3S+ Multilang):
Flash: -62 bytes
SRAM: -6 bytes
2023-02-18 16:32:08 +01:00
8b1b632164
Fix copy/paste typo thanks to @gudnimg
2023-02-10 14:35:36 +01:00
4f8dbb19fd
Fix `M862.x` LCD messages
...
As the new menue adds a Yes/No option the messages
need to be limited to c=20 r=3
Updated/shortened all translations
2023-02-10 14:35:36 +01:00
ca978080c4
Change to Thermal model
...
Add prusa.io/tm-cal link
and update all TM related translations
2023-02-08 15:36:59 +01:00
b28aa6f42a
PFW-1471 Rename 'Toolchange count' to 'Material changes'
...
Added the string to our message so it can be translated
Change in memory:
Flash: -10 bytes
SRAM: 0 bytes
2023-02-06 08:33:40 +01:00
dba3428ef2
Improve MSG_ACK_ERROR message
2022-12-17 20:25:47 +01:00
3d-gussner
sarusani
sarusani
Panayiotis-git
gudnimg
Juan Francisco Estrada
Alex Voinea
D.R.racer
Yuri D'Elia