613ea290f5
Add a comment
2022-12-10 10:04:17 +00:00
9ed46df97f
Don't show full screen message meant for single color setup
...
load_filament_to_nozzle will show a more precise full screen message when an MMU is used.
2022-12-10 10:00:58 +00:00
70451b6bd3
Turn off print fan while restoring print from RAM
2022-12-10 09:53:43 +00:00
40cc6dcb6d
Merge pull request #3783 from leptun/enable_PRUSA_SN_all_variants
...
Allow "PRUSA SN" to print the SN in eeprom on all variants
2022-12-09 14:51:57 +01:00
1e39012953
Merge pull request #3793 from gudnimg/PFW-1453
...
PFW-1453 Stop Print: Don't unload if FINDA is not triggered
2022-12-09 12:54:16 +00:00
68c5cdce1c
Merge pull request #3780 from gudnimg/stop-print-optimisations
...
optimisation: Improve Stop Print menu
2022-12-08 19:41:52 +01:00
92f2281b1a
Merge pull request #2335 from Panayiotis-git/MK3_NoBedHeating_onLoadUnload
...
@Panayiotis-git Thanks a lot!
Finally after 3 years 21 days your PR gets merged 🦕
2022-12-08 18:45:12 +01:00
0cedb92ac6
Simplify firmware/gcode version comparisons
2022-12-07 18:59:29 +01:00
96e4881da5
Merge pull request #3794 from gudnimg/fix-m862-q
...
Fix undefined pointer in `M862.2 Q` and `M862.3 Q`
2022-12-07 13:04:45 +01:00
6f5a67491c
Fix `M862.4` with [strict] mode
...
Max 8 falvor versions
2022-12-06 13:18:52 +01:00
1c9a3a6b25
Add Nozzle change menu to FARM mode under Settings
2022-12-05 18:22:18 +01:00
a8fe71df8c
PFW-1453 Stop Print: Don't unload if FINDA is not triggered
2022-12-05 16:45:57 +01:00
52965bd05d
Avoid using global variables
...
Flash: -68B
RAM: -4B
2022-12-05 16:43:51 +01:00
4c27d057b8
Don't inline fSetMmuMode
...
Saves 8 bytes of flash
2022-12-05 16:43:51 +01:00
074b62361f
Fix #3788
...
fSetMmuMode needs to be called
in order for the commands to work:
M862.2 Q
M862.3 Q
2022-12-05 16:43:51 +01:00
c75c81ce4f
Do not heat the bed, on load/unload
...
If during a paused print, the preheat is canceled, keep the bed target temperature
Display bed temperatures only if bed is also heated
Remove not needed variables nTargetOld and nTargetBedOld from the mFilamentItem function
Define new Setting "HeatBedOnLoad" [Yes/No]
2022-12-04 19:26:34 +02:00
fb530ce543
PFW-1454 Send button to MMU on MMU SELFTEST FAILED screen
...
Fixes an issue where the button on the MMU error screen doesn't do anything
when MMU SELFTEST FAILED is rendered
2022-12-04 11:04:00 +00:00
6d62fb0d65
Merge pull request #3784 from DRracer/opt01
...
Optimize rendering MMU Error sensor line
2022-12-02 17:12:05 +00:00
3e976e04ca
Merge pull request #3777 from 3d-gussner/PFW-1431
...
PFW-1431: Add "PA Preheat"
2022-12-02 13:34:18 +01:00
54ef2a6c28
Merge pull request #3769 from 3d-gussner/MK3_Temp_model_cal_wizard
...
PFW-1434: MK3 Temp model calibration during wizard
2022-11-30 15:33:38 +01:00
1bbcdb0c0d
Merge pull request #3774 from 3d-gussner/MK3_Nozzle_change
...
PFW-1435 Nozzle change menu
2022-11-30 15:32:18 +01:00
0a6388cc56
Update internal translations
...
Fix G28 W
2022-11-30 15:01:24 +01:00
500131d51d
fullscreen message: use \n to force the next word on the next line
...
Useful for printing short URLs since those contain punctuation characters, which get treated at the end of a word under usual circumstances
2022-11-30 10:17:28 +01:00
8f44d1102c
Add PA preheat menu
2022-11-30 06:42:32 +01:00
23613c7eb1
optimisation: Stop print menu
...
There is no need to manually track the cursor position.
We can use the menu API:
MENU_BEGIN()
...
// menu items in between here
...
MENU_END()
Change in memory:
Flash: -116 bytes
SRAM: 0 bytes
2022-11-26 10:18:47 +00:00
a666c0f6f4
Optimize rendering MMU Error sensor line
...
CPUFLASH: -32B
2022-11-25 13:30:53 +01:00
83c9e946e4
Fix recursion
2022-11-24 16:15:51 +01:00
4f3c188017
Update internal translations
...
Fix typo
2022-11-24 10:53:04 +01:00
fea1520dfb
Fix & optimize FW version parsing and checking
...
PFW-1433
2022-11-23 13:34:13 +01:00
32673e1681
Nozzle change menu
2022-11-23 11:39:26 +01:00
2cd42f8433
Fix typo
...
Add Norwegian translations thanks to @OS-kar
2022-11-22 08:26:20 +01:00
c8157919b1
PFW-1440 Fix issue where cooldown timer is not set after a faile retry
2022-11-21 12:54:53 +01:00
37ac33bc32
Fix compiler warning
2022-11-21 12:54:53 +01:00
fe6e3ca2b1
Unload first before retrying
...
Should free the filament if accidentally held by the fsensor.
2022-11-20 19:23:07 +01:00
5639620041
Avoid watchdog while doing VerifyFilamentEnteredPTFE
2022-11-20 17:27:36 +01:00
84d9eee61d
Resume hotend temperature if parked + MMU restarted
...
PFW-1355
2022-11-20 17:27:36 +01:00
01c1f4a8dd
Load test: Monitor unload as well
2022-11-20 17:27:36 +01:00
5c8ea4c90a
fixup
2022-11-20 17:27:36 +01:00
327f0edb17
VerifyFilamentEnteredPTFE must take into account the Extra Loading Distance
2022-11-20 17:27:36 +01:00
c9d9ba0b1a
Add a bracket around subtraction, just in case
2022-11-20 17:27:36 +01:00
ef51b5778d
Fix VerifyFilamentEnteredPTFE
...
Test should push filament first and then retract.
2022-11-20 17:27:36 +01:00
aaebaf163f
Cleanup MSG_MMU_POWER_FAILS
2022-11-20 17:27:36 +01:00
a17153f877
Make TMC mask more readable
2022-11-20 17:27:36 +01:00
f1ed2fc5c7
Fix issue where tool_change_extruder is not reset after retry
2022-11-20 17:27:36 +01:00
541cd3ae94
Remove debug messages of Interrupted state
2022-11-20 17:27:36 +01:00
46f4f2658d
PFW-1432 Reduce LOC
...
If verification test fails, increment load fail statistic
2022-11-20 17:27:36 +01:00
03235c8aab
PFW-1432 restore toolchange load testing
2022-11-20 17:27:36 +01:00
adb24cd410
Increment errors in ReportError
2022-11-20 17:27:36 +01:00
4eaabbf092
Revive MMU stats + LCD screens
2022-11-20 17:27:36 +01:00
fe11b7a247
Tune Interrupted state based on unit tests
...
Now finally the printer can restart ToolChange if MMU restarted.
2022-11-20 17:27:36 +01:00
ffbd95b482
Unify naming convention (index->slot)
...
in all top level MMU-related functions
2022-11-20 17:27:36 +01:00
e414413b2e
Refactor ToolChange+LoadToNozzle
...
Add basic infrastructure for handling of repeated commands until they finish correctly.
2022-11-20 17:27:36 +01:00
10a9e0f0a0
Recover from MMU restart while performing a command
...
PFW-1427
2022-11-20 17:27:36 +01:00
603faddd25
Fix bug where toolchange counter is not rendered
2022-11-20 15:42:29 +00:00
5dc539cda5
fixup
2022-11-20 13:12:01 +01:00
62810c5a7c
optimisation: lcdui_print_extruder
...
Simplify the rendering to cover more scenarios:
"[nr.]>?"
"?>?"
Both of these indicate there is a bug in the firmware.
Currently these are not handled and result in the status screen being corrupted.
This is because we are trying to write a 3 digit number
where there is not space on the LCD for it.
Change in memory:
Flash: -52 bytes
SRAM: 0 bytes
2022-11-20 13:12:01 +01:00
281a217549
Update Temp Model messages
...
Deepl translate cs,de,es,fr,it,nl,pl
2022-11-20 10:49:46 +01:00
f2f54da5b0
Unhack selftest hack during wizard
2022-11-20 10:48:49 +01:00
d592586d94
cleanup: remove dead code lcd_adjust_z()
...
It's only used when MESH_BED_LEVELING is not defined. According to
the configuration files, all printers supported use MESH_BED_LEVELING.
So I think we are safe in removing this dead code.
2022-11-19 22:19:48 +00:00
411d1da3c8
Merge pull request #3763 from gudnimg/optimisation-float-conversions
...
optimisation: TCodes accepts `uint8_t` not `float`
2022-11-18 19:52:22 +00:00
58775b8b55
Change unsigned long to uint32_t
2022-11-18 14:50:07 +01:00
bda134a01e
Save a bit of RAM from CS
...
Do not store EEPROM_VERSION in ram
flash: -6
RAM: -2
2022-11-18 14:50:07 +01:00
ef83fefce1
More optimization
2022-11-18 14:50:07 +01:00
8f4ac82273
eeprom_init_default also returns the read/default value
2022-11-18 14:50:07 +01:00
b317786110
More configuration store savings
...
flash: -94B
RAM: 0B
2022-11-18 14:50:07 +01:00
b551bdae76
Some more CS improvements
...
flash: -2B
RAM: 0B
2022-11-18 14:50:07 +01:00
5305dbd299
Sheet name initialization improvements
...
The code looks better, but it takes a bit more flash. I prefer it like this
flash: +20B
ram: 0B
2022-11-18 14:50:07 +01:00
bba5385a61
Move string to progmem
...
flash: -84B
RAM: -4B
2022-11-18 14:50:07 +01:00
6edc71d0ae
Remove deprecated configs
2022-11-18 14:50:07 +01:00
dcc48c0052
Remove eeprom _int8t functions
...
flash: -48B
RAM: -4B
2022-11-18 14:50:07 +01:00
af60cd7d79
Optimize EEPROM_writeData and EEPROM_readData
...
flash: -162B
RAM: -4B
2022-11-18 14:50:07 +01:00
771f833a44
Implement eeprom dword functions
2022-11-18 14:50:07 +01:00
ca943cceec
Split the increment function into increment and add
...
No size difference since the compiler did a good job optimizing the inc argument (always 1 before).
2022-11-18 14:50:07 +01:00
455c29e78b
Optimize EEPROM usage/functions
2022-11-18 14:50:07 +01:00
414d3f1c12
Display Welcome message after MMU progress report ends
...
Should make the status line look cleaner when the printer is not printing.
2022-11-18 14:09:48 +01:00
c86c961d4e
M600: Fix bug where fan is not turned off
...
The firmware saves the current fanspeed before parking,
and the fanspeed is restored after unparking. The problem is the fan
was never actually paused.
Fixes #3670
2022-11-18 11:18:29 +01:00
b147fcee77
XYZ calibration fixes
2022-11-18 00:18:42 +01:00
384a6d1989
Fix wizard serial messages
2022-11-17 23:03:03 +01:00
30ec4e8b53
Inital Temp Model cal wizard
2022-11-17 15:19:35 +01:00
2096accc5f
Remove unused gcode level check code
...
This code was introduced with v3.8.0 but was always disabled.
I propose the code be removed since it has not been enabled
for 3 years since its introduction.
2022-11-17 08:05:27 +01:00
6059398004
Introduce MMU Error: INSPECT_FINDA (FINDA_FLICKERS)
2022-11-17 07:58:11 +01:00
29882b625b
Remove LcdCommands::FarmModeConfirm
2022-11-17 05:46:33 +01:00
e11ef11a64
PFW-1425 Rename "Load to Extruder" to "Loading Test"
2022-11-16 06:00:15 +01:00
7b43f322de
PFW-1425 Move Reset MMU setting
2022-11-15 17:32:27 +01:00
b4920d7fa8
PFW-1425 use mmu2.Enabled instead of EEPROM read
2022-11-15 17:32:27 +01:00
3f4ac254ab
PFW-1425 Move MMU settings under a common if statement
...
We only need to check if the MMU is enabled once,
no need to do it in every submenu.
This way we save little bit of flash memory.
Change in memory:
Flash: -24 bytes
SRAM: 0 bytes
2022-11-15 17:32:27 +01:00
8f3f071fd4
PFW-1425 Move Load to Extruder menu to Settings menu
...
No change in memory footprint
2022-11-15 17:32:27 +01:00
5239f1c176
cleanup: remove old extern for mmu_print_saved
2022-11-15 09:44:02 +01:00
4f58812478
optimise lcd_sdcard_menu with lcd_print_pad
...
Change in memory:
Flash: -46 bytes
SRAM: 0 bytes
2022-11-13 09:29:37 +01:00
184e19dd60
further optimise lcdui_print_status_line
...
We can use lcd_print_pad to determine
whether the end of the file name was reached
lcd_print_pad now returns the last character pointed to.
If the end of the string was reached, it will be the null delimeter which
evaluates to "false" in an if statment (same as NULL).
Else "true" means the end of the string was not reached.
Change in memory:
Flash: -42 bytes
SRAM: 0 bytes
2022-11-13 09:29:37 +01:00
0af7ef0201
optimisation: reduce code size in showing file name being printed
...
Change in memory:
Flash: -52 bytes
SRAM: 0 bytes
2022-11-13 09:29:37 +01:00
a2bbc4f585
Merge pull request #3745 from leptun/MK2.5_XYZ_Cal_fixes
...
MK2.5 XYZ calibration fixes
2022-11-12 21:48:16 +01:00
006fe110cc
Don't raise MMU error screen until retry is done
...
Change in memory:
Flash: +8 bytes
SRAM: 0 bytes
2022-11-12 18:47:10 +01:00
68bd7f9b19
Fix excessive flash usage.
2022-11-12 18:47:10 +01:00
ecef69012a
Fix PFW-1364 & possible comms timeout during reheat
2022-11-12 18:47:10 +01:00
509813f60b
optimsation: TCodes accepts uint8_t not float
...
Change in memory:
Flash: -20 bytes
SRAM: 0 bytes
2022-11-12 16:50:45 +00:00
661b3a83ff
MK2.5: fix swapped yes/no messaged for Z manual alignment
2022-11-10 22:20:46 +01:00
1cdc2e712b
MK2.5: unblock planner after plan_abort_hard()
2022-11-10 22:20:01 +01:00
fd832f9ccf
Merge pull request #3737 from gudnimg/fix-longpress-inactivity-timeout
...
Fix long-press LCD inactivity timeout
2022-11-08 14:10:57 +01:00
76a164e651
fixup
2022-11-08 13:49:40 +01:00
08460bd403
PFW-1397 Drop ON_MENU_ENTER
...
Using _menu_data_t turns out to save *just* a little bit more flash. So for now just use it.
2022-11-08 13:49:40 +01:00
390f69a82f
PFW-1397 Fix: ON_MENU_ENTER was always run
2022-11-08 13:49:40 +01:00
59a452ac27
PFW-1397 minor comment tweaks
2022-11-08 13:49:40 +01:00
f160f5594d
PFW-1397 cleanup statistics menu
...
Change in memory:
Flash: -18 bytes
SRAM: -1 byte
2022-11-08 13:49:40 +01:00
82bd9db1d6
PFW-1397 Implement ON_MENU_ENTER to simplify code
...
ON_MENU_ENTER runs code within the brackets only once
after a new menu is entered.
For the tool change menu, this allows us to display the data and
read from EEPROM only once.
2022-11-08 13:49:40 +01:00
a896dfd4e0
PFW-1397 To reserve EEPROM write cycles, only update toolchange counter when a print finishes or is stopped
2022-11-08 13:49:40 +01:00
3120bf0aa2
PFW-1397 Implement new function increment_tool_change_counter()
...
Reduces flash consumption by 44 bytes
2022-11-08 13:49:40 +01:00
fcfb868167
PFW-1397 Add a temporary menu item to show the statistic
...
The location of the menu has not been decided. Currently I placed it where convenient.
2022-11-08 13:49:40 +01:00
5a60a85467
PFW-1397 Increment toolchange statistic
2022-11-08 13:49:40 +01:00
0af7d28074
PFW-1397 Allocate EEPROM memory for toolchange counter
2022-11-08 13:49:40 +01:00
7fe22e8f79
Fix long-press LCD inactivity timeout
...
Fixes #3715
When a long-press is triggered, the LCD inactivity timer
needs to be restarted. This is done with lcd_timeoutToStatus.start()
This also fixes situations where a long-press is triggered, and the timer
times out immediately (because it was not reset properly)
Change in memory:
Flash: +8 bytes
SRAM: 0 bytes
2022-11-06 13:43:14 +00:00
853adbf411
Bump up build number
...
+1 for commit
+1 for merge
2022-11-04 11:16:07 +01:00
7c009cadb8
Bump up Revision to ALPHA1 6051
...
Temporary fix for MSG_BTN_MORE
pre-release pot and po update
2022-11-04 10:21:39 +01:00
7b20f8c6f3
Merge pull request #3717 from 3d-gussner/MK3_Temp_Model_menu
...
Add Menu `Calibration -> Temp. model cal`
2022-11-03 12:12:55 +01:00
1e0909d50c
Disable `Error:` messages for MMU2 errors
2022-11-03 12:09:03 +01:00
8543942acb
Fix Z-leveling
2022-11-03 06:22:57 +01:00
fd6da0e766
Fix typo
...
Add lcd_setatatus_serial to output lcd status message and serial at the same time
2022-11-02 10:09:32 +01:00
7bc7f21fa5
mmu: move RetryIfPossible outside the error screen
...
This fixes issue where 'retryAttempts=3' may be spammed in the logs
Change in memory:
Flash: 0 bytes
SRAM: 0 bytes
2022-11-01 06:22:39 +01:00
2ac2cd2255
Fix MK25/S builds
2022-10-26 14:27:22 +02:00
072b3f8300
Temp Model cal. menu
2022-10-26 13:34:27 +02:00
f4a2c1c794
Update translations
...
Fix button msg
Update Dutch `F. jam detect`
2022-10-25 10:29:35 +02:00
45c72d48ed
optimisation: use failstats_reset_print in factory_reset_stats
...
Change in memory:
Flash: -56 bytes
SRAM: 0 bytes
2022-10-23 09:58:56 +00:00
edc5d013dd
Merge pull request #3698 from leptun/farm_presort_cache
...
Farm mode: cache filenames in the presort function
2022-10-21 15:43:49 +02:00
b792d47350
Merge pull request #3694 from 3d-gussner/MK3_Hotend_fan
...
PFW-1415: Rename `Extruder fan` to `Hotend fan`
2022-10-19 08:47:15 +02:00
b485992c9e
If in farm mode, force the sorting direction to be reversed
...
So in an ideal scenario, the newest file is first. This of course breaks as soon as a file is deleted/renamed/moved, but it should at least be fixed now compared to before where the direction could be influenced by a disabled setting
2022-10-18 17:29:31 +02:00
798f215f88
Refactor SD menu settings
2022-10-18 17:24:35 +02:00
eaaf1d6872
Rename Sheets
...
- `Satin 1` to `Satin `
- `Satin 2` to `NylonPA`
2022-10-18 10:20:01 +02:00
e18bfce597
Farm mode: cache filenames in the presort function
2022-10-17 20:17:28 +02:00
e83728f72c
Change fan RPM display to 5 digits
...
All credits to @ WarrenSchultz for initial PR https://github.com/prusa3d/Prusa-Firmware/pull/3656
2022-10-17 15:41:05 +02:00
f2fe9a51ee
rename `Extruder fan` to `Hotend fan`
2022-10-17 13:49:18 +02:00
2682b64a09
Optimisation: Reduce code size in rendering SD file names and folders
...
Change in memory:
Flash: -88 bytes
SRAM: 0 bytes
2022-10-12 20:19:21 +00:00
2c695f14be
Increase required MMU version to 2.1.4.x
2022-10-12 07:45:13 +02:00
6eab0dda59
Add parentheses - be more explicit in error codes' masking and comparison
2022-10-11 15:51:01 +02:00
0aeb74e5b1
Intercept M708 A0xb: set ExtraLoadDistance on the printer side too
2022-10-11 15:51:01 +02:00
b0466ae20f
Add infrastructure for MMU parametrization after comm start
...
For now, only the Extra loading distance is being sent, but the infrastructure can be easily extended for other registers as well.
2022-10-11 15:51:01 +02:00
c7e4c9ce99
Allow backwards compatibility with legacy MMU g-codes
...
This piece just changes the default extra load length on the MK3 side.
The same needs to be done on the MMU side but:
- the MMU exposes its register for this (so we can change the extra load distance by writing into the register via G-code)
- the printer shall probably set this value on its own after line up of MMU communication
2022-10-11 15:51:01 +02:00
013ce588a5
Support reading/polling multiple registers
...
In Idle and Command mode it is now possible to specify a list of registers which shall be periodically read from the MMU.
To keep the code and RAM size down registers are intentionally separated into 8bit and 16bit sets.
Adding a register into the set is just a matter of parametrization, there is no need to change the state machines anymore.
2022-10-11 15:51:01 +02:00
ebb79351a7
Add preliminary support for MMU_SELFTEST_FAILED error messages
2022-10-11 15:51:01 +02:00
d5ca47d1a6
Merge pull request #3646 from gudnimg/fix-mmu-buttons-v2
...
PFW-1403 Fix issue where physical MMU buttons do not dismiss error screen
2022-10-11 13:42:39 +02:00
8882d8f2c8
Only move XY when position is known
...
I had a crash when producing an error screen and printer was unhomed.
Extruder was located at the far right side, and immediately crashed when attempting to park.
2022-10-11 07:16:52 +02:00
9f3361577e
Merge pull request #3643 from gudnimg/PFW-1358
...
PFW-1358 More button utilizes text and an empty character on the right
2022-10-10 18:02:22 +00:00
98cfc37017
Merge pull request #3674 from gudnimg/mmu-first-lay-cal-purge-line
...
MMU: Sync first layer purge line with PrusaSlicer generated output
2022-10-10 17:59:18 +00:00
213f0e8c71
PFW-1358 Update second_col description
...
Value is no longer hardcoded
2022-10-10 17:48:56 +00:00
eb43d712df
Enable MISO pullup during SD CMD0
...
Fix typo
2022-10-10 09:43:50 +02:00
ccf0c0a09f
Merge pull request #3675 from gudnimg/pad-mmu-status-messages
...
Fix issue where MMU status messages are not padded
2022-10-09 10:49:55 +00:00
1c6345a85b
Fix issue where MMU status messages were not padded
...
Also combined common cases to reduce code size
2022-10-09 10:37:33 +00:00
76dc51d2f0
Sync first layer purge line with PrusaSlicer generated output
...
If you generate a multicolor gcode file with PrusaSlicer, the purge
line gcode will look like this.
This reduces clicking sounds from the extruder, filament extrusion is reduced by 6mm.
2022-10-09 10:03:54 +00:00
d483531606
PFW-1358 update c values
2022-10-08 09:40:43 +00:00
00ccdcd467
PFW-1358 change MSG_BTN_MORE from I1 to N1
2022-10-08 09:25:06 +00:00
d6e0f47739
PFW-1403 Rename ReportErrorSource to ErrorSource for shorter code
2022-10-08 08:51:32 +00:00
33690b927a
PFW-1403 Fix issue where physical MMU buttons do not dismiss error screen
2022-10-08 08:51:32 +00:00
8f0de44d84
PFW-1358 Move 'More' button to the corner of the screen
...
Make 'More' button position consistent with 3-button screen.
2022-10-08 08:50:40 +00:00
7264391c5f
PFW-1358 Fix and optimise button choice positions
2022-10-08 08:50:40 +00:00
9046fb3d44
PFW-1358 Adjust positions of button choices
2022-10-08 08:50:39 +00:00
06427087c0
PFW-1358 Change "More" button to single character
2022-10-08 08:50:39 +00:00
233174cf86
Fill the doc for the EEPROM value at 0x0DA1 - active_sheet
2022-10-07 11:59:57 +02:00
2067cddc46
Merge pull request #3631 from 3d-gussner/MK3_fix_eeprom_documentation_part1
...
MK3 fix eeprom doxygen documentation
2022-10-06 15:29:15 +02:00
629fc9d0f1
Merge pull request #3638 from wavexx/tm_cal_click
...
TM: Consume LCD click after calibration
2022-10-06 14:29:40 +02:00
bab83704a1
Fix Typo 0X0 to 0x0
2022-10-06 13:23:16 +02:00
bfaed2768c
Merge pull request #3652 from wavexx/cmake_build_v2
...
cmake build improvements v2
2022-10-05 14:20:28 +02:00
d867da201f
cmake: Define FW_VARIANT instead of copying Configuration_prusa
2022-10-05 01:26:30 +02:00
1d3ee1caba
build: Add Configuration_var.h as a configuration wrapper
...
Instead of including Configuration_prusa.h directly, include
Configuration_var which then includes the proper variant file though a
preprocessor macro.
This allows to keep the existing build system intact, but also redefine
at compile time the final header without having to make copies on the
file system.
2022-10-05 01:26:26 +02:00
2ae376d633
build: Size optimization
...
Explicitly force-noinline xyzcal_scan_pixels_32x32_Zhop to match the
previous LTO build behavior.
2022-10-04 12:13:09 +02:00
5ed6bd7f8b
cleanup: Fix more spourious missing return warnings
...
Rewrite to use a temporary and get rid of the warning.
The generated asm is *unchanged*.
2022-10-03 21:54:08 +02:00
992845198d
Merge pull request #3648 from wavexx/more_cleanups
...
cleanup: Expand tabs to fixup suspicious indentation warnings
2022-10-03 11:53:42 +02:00
4cc6695195
cleanup: Expand tabs to fixup suspicious indentation warnings
2022-10-02 20:42:36 +02:00
a8e85bd146
cmake: Work-around gcc 7 not supporting SOURCE_DATE_EPOCH
2022-10-02 20:32:32 +02:00
1d520f9165
cmake: Make builds fully reproducible by default
...
- Work-around SOURCE flags being reset for each project when setting the
random-seed property by calling a support function.
- Likewise, set correct flags for reproducibility when creating archives.
- Strip source prefix paths from debug info
This should set the EPOCH using the last git commit date when available,
but it's not currently implemented. Just set the EPOCH to be 0 for now.
2022-10-02 20:32:32 +02:00
d8c9c4450f
Merge pull request #3641 from vintagepc/build-with-cmake
...
Build the firmware with cmake
2022-10-02 13:05:32 -04:00
c7b6b9a99b
cleanup: Suppress unused argument warnings
2022-09-30 15:08:11 +02:00
c522330433
Merge remote-tracking branch 'upstream/MK3' into build-with-cmake
2022-09-30 09:04:35 -04:00
49f96213a4
Also consume longpress in lcd_consume_click()
2022-09-30 14:29:37 +02:00
b95d508574
cleanup: Remove implicit fallthrough in CRC validation
2022-09-30 12:55:47 +02:00
71be6b19d4
cleanup: Remove return value from MMU2Serial::write()
...
Removes a missing return warning.
Looks like we don't handle overflow at the moment and in all surrounding
code, so let's remove the return value for now.
2022-09-30 12:55:47 +02:00
6cfe000ac9
cleanup: Reorder members to match initialization order
2022-09-30 12:55:47 +02:00
398a4bf403
cleanup: Do not return const values from functions
...
This generates a warning under -Wextra, since in most cases a const
value doesn't prevent buggy code (as copies are allowed) while
preventing some optimizations (such as move operations) to take place.
2022-09-30 12:55:47 +02:00
d6af13dfc1
cleanup: Supress missing return warnings
...
Rewrite the function with a temporary to avoid the spourious no-return
warning.
The generated code is *unchanged*.
2022-09-30 12:31:07 +02:00
31ea48246a
TM: Consume LCD click after calibration
...
Consume any pending LCD click after the temperature model calibration.
Since we're already in the status menu, the usual consume action is not
done automatically here.
2022-09-30 12:24:54 +02:00
74e15ac233
Rename EN_ONLY to EN_FARM
...
remove DEBUG/DEVEL/ALPHA/BETA lcd warning
2022-09-29 16:39:02 +02:00
346dfbdbb3
Fix MSG_SPOOL_JOIN
2022-09-29 10:54:46 +02:00
c7b500af1e
BETA firmware message only in English
...
Rephrase BETA firmware message to fit on two screens
ALPHA message same as DEVEL
Fix ALPHA DEVEL message
2022-09-29 10:48:16 +02:00
1a8f18318c
Add Temp Model eeprom documentation
2022-09-28 18:15:23 +02:00
302e4b679c
replace tab with spaces
2022-09-28 17:37:46 +02:00
709d07310a
lcd_print_pad: do not overflow len when truncating the string
2022-09-26 11:26:10 +02:00
7fb53899dc
Merge branch 'MK3' into MK3_MMU2_fix1
2022-09-23 14:55:23 +02:00
26b091d50e
Remove unneeded lcd_finishstatus()
2022-09-23 11:54:16 +02:00
80c06bda55
Improve warning behavior during thermal anomaly
...
The current code forces any warning to return the user to the status
screen in order to show the message.
Thermal anomaly warnings can repeat at very short intervals, making menu
navigation (to pause/tune the print) impossible.
We now check if the message to be displayed is the same and only force a
kickback for new messages.
This partially reverts https://github.com/prusa3d/Prusa-Firmware/pull/3600
since we need the string to be null terminated for ease of comparison.
We pad the status line at display time instead using the new
lcd_print_pad() function which achieves the same effect.
2022-09-22 16:12:35 +02:00
24b638b5d4
fixed undefined behaviour when left shifting a negative number
2022-09-21 16:21:19 +02:00
9a9aadca87
Do not hang during startup
...
In ultralcd_init() do not use lcd_setstatuspgm() to initialize the
welcome message.
The internal call to lcd_finishstatus() requires the serial to be
already available. Split the function into lcd_padstatus() to pre-pad
the string and save some space.
2022-09-21 16:12:16 +02:00
f7d4095479
Merge branch 'MK3' into MK3_MMU2_fix1
2022-09-21 15:18:44 +02:00
2cdd3ba364
Move strings to progmem
2022-09-21 14:53:54 +02:00
16d1ef8510
Merge pull request #3560 from leptun/splash_version
...
Show firmware version on splash screen
2022-09-21 14:47:41 +02:00
a1213d6a6e
Merge pull request #3600 from gudnimg/init-lcd-status
...
Fix initialization of LCD status line message
2022-09-21 14:46:10 +02:00
ca9a28eff2
Merge pull request #3612 from wavexx/tm_update_r0
...
Temperature model: update R0 estimate
2022-09-21 14:46:03 +02:00
bccdab4c22
Merge pull request #3615 from wavexx/line_cnt_reset_fix
...
Do not reset line on serial commands without N
2022-09-21 14:45:46 +02:00
183e21aa0b
Merge pull request #3599 from 3d-gussner/MK3_MMU2_messages
...
PFW-1339 - Update MMU2 translations
2022-09-21 10:27:01 +02:00
129df6dd4a
Do not reset line on serial commands without N
...
Fix regression introduced in fc10ca3146
2022-09-21 10:19:16 +02:00
1c4e9463ec
Temperature model: update R0 estimate
...
Update the default R0 estimate thanks to a larger dataset.
This improves the error margin during self-check.
2022-09-20 16:57:54 +02:00
eb7de5149b
Don't inline the function
...
Change in memory:
Flash: -44 bytes
SRAM: 0 bytes
2022-09-20 06:34:24 +02:00
c8a8484ca7
Remove atomic_update parameter
...
Change in memory:
Flash: +24 bytes
SRAM: -0 byte
2022-09-20 06:34:24 +02:00
76fb4610ea
Optimisation: Remove duplicated code in cmdqueue_could_enqueue_back()
...
Code is 28 lines shorter :)
Change in memory:
Flash: -42 bytes
SRAM: 0 bytes
2022-09-20 06:34:24 +02:00
156b5e5b99
Update current FW version
2022-09-19 18:15:39 +02:00
6a470791d3
Allow sending uint16_t values to registers
2022-09-19 15:13:37 +02:00
770fdcd83b
Fix typo, thanks to @gudnimg
2022-09-19 08:02:40 +02:00
28b0ef1acb
PFW-1369 Use same ramming sequence as default settings in Slicer
2022-09-19 07:23:03 +02:00
075a80e264
Add missing text
...
Finish Dutch translation
2022-09-17 17:38:45 +02:00
068f4763e2
Update translatable strings to match our extraction macros
...
Update pot and po files
2022-09-17 16:53:30 +02:00
47d7ea5dfd
Add MSG_LOAD_ALL and replace it a two loactions -10bytes flash
2022-09-17 16:36:09 +02:00
25a7dc8397
Fix: Filament Already Loaded only has two buttons
2022-09-17 16:36:09 +02:00
15a8c8fe37
Fix: Unload Manually did not send any button to the MMU
2022-09-17 16:36:09 +02:00
9b4a621275
Fix: Fsensor errors only have one reset button
2022-09-17 16:36:09 +02:00
037d51b049
Fix: Filament Already Loaded only has two buttons
2022-09-17 12:21:42 +02:00
3b60b894da
Fix: Unload Manually did not send any button to the MMU
2022-09-17 12:21:42 +02:00
e7b7d97f11
Fix: Fsensor errors only have one reset button
2022-09-17 12:21:42 +02:00
be7c1d55c8
Remove redundant for-loop
...
Now that lcd_status_message is now initialised correctly at boot-up,
this for-loop is no longer required. Now lcd_status_message is
only set in lcd_updatestatus() which always calls lcd_finishstatus()
lcd_finishstatus() makes sure the message does not exceed 20 characters
Saves 34 bytes of flash
2022-09-17 09:13:07 +00:00
4d6d267aef
Don't initialise lcd status message in definition
...
static variables are automatically zero initialised. Now that the
status line message is initialised in ultralcd_init(), we don't
need to set the variable in global scope.
Saves 22 bytes of flash and 1 byte of SRAM
2022-09-17 08:57:30 +00:00
f1e127ace4
Initialise status line message in setup()
...
Fixes #3581
2022-09-17 08:53:36 +00:00
404c622301
Finish German translation
...
increase 2nd langusge size to 0x3500 13567bytes to fit mmu2 translations 🤞
2022-09-17 10:35:30 +02:00
ec22e5faeb
Shorten message to 20 chars
...
add 01234567890123456789 ruler
2022-09-17 10:34:24 +02:00
539cdbfeea
Lower MSG_ rows
2022-09-17 08:48:56 +02:00
78fdf33f67
Update Firmware.pot and Firmware_de.po
...
Started German translation Part 1
Updated c= r= for German translations being longer than 8 rows
2022-09-16 20:42:50 +02:00
8480c1cb7a
Added //#define FARM_CONNECT_MESSAGE
2022-09-16 19:33:22 +02:00
88b58cdcd5
Update messages missing c= r=
...
Change MMU2 KEEPALIVE_STATE to IN_PROCESS
2022-09-16 19:24:11 +02:00
f4f09e4062
update mmu2 messages c= r= values
2022-09-16 19:18:23 +02:00
0f8d84082a
Update button menu documentation as there are 1/2/3 options
2022-09-16 19:11:11 +02:00
9d959f5d12
Prepare progress messages for translation
...
Remove duplicate messages
2022-09-16 19:08:06 +02:00
89a03c1f0d
MMU2/lang: Update translatable strings to match our extraction macros
2022-09-16 19:02:04 +02:00
50b6044703
Use origin message on serial
2022-09-16 18:17:50 +02:00
3f6b05cc35
Remove PAT9125 stats as these aren't different to IR stats
2022-09-16 18:04:21 +02:00
2ba863d8a5
Reuse MSG_IR_0x_OR_..
...
fix lowercase
remove todos
2022-09-16 17:23:38 +02:00
edad625cf7
RIP Bondtech long live the Extruder
2022-09-16 16:31:27 +02:00
37cde856e9
Rename Auto_deplete to Spool_join
...
Fix some missing MSG_ c= r=
2022-09-16 16:25:47 +02:00
f18493f361
Save some space due to shorter MMU error texts
...
applies https://github.com/prusa3d/Prusa-Error-Codes/pull/62
2022-09-16 12:12:08 +02:00
2d98cae8bd
Fixup MK3_MMU2 branch after rebase onto MK3
2022-09-16 11:08:03 +02:00
16713aa25a
Optimisation: scopeState is already set by SendReadRegister
...
Saves 2 bytes of flash
2022-09-16 10:23:47 +02:00
e9f5a95d4b
PFW-1362 Make sure FINDA runout is impossible with MMU disabled
...
Since mmu_loop() is called in the main loop() function
when the MMU is disabled, we need to utilise the
MMU protocol layer to prevent FINDA runout from happening
if MMU is disabled.
We also need to keep in mind we probably can't trigger
a FINDA runout in the middle of a Q0 query.
So my solution now is to wait for the "Finished" state
and check if the FINDA is off during printing.
When "Finished" state appears, the FINDA value should be up
to date.
2022-09-16 10:23:47 +02:00
94119744ad
PFW-1362 Change isSpoolJoinEnabled to return bool
2022-09-16 10:23:47 +02:00
65a0036dbe
PFW-1362 Optimise debug message
...
Saves 20 bytes of flash :)
2022-09-16 10:23:47 +02:00
998ed87f25
PFW-1362 Use PROGMEM messages
...
The main purpose of these two messages is just to see if SpoolJoin is enabled or not.
"On" and "Off" are descriptive enough.
Saves 16 bytes of flash
2022-09-16 10:23:47 +02:00
63b4abb66d
PFW-1362 SpoolJoin needs to known what the previous slot was
2022-09-16 10:23:47 +02:00
1010f23959
Fix an issue where findaPressed is never set
...
This caused instant FINDA runout when the print starts. Now fixed :)
2022-09-16 10:23:47 +02:00
b292a5bf4e
PFW-1362 temporarily don't use SpoolJoin in Tcodes
...
I think in the current implementation, this will cause more harm than good.
But we can improve SpoolJoin later
2022-09-16 10:23:47 +02:00
7dcfc1484e
PFW-1362 temporary debug messages
2022-09-16 10:23:47 +02:00
8610636906
PFW-1362 Add a log when FINDA filament runout is triggered
2022-09-16 10:23:47 +02:00
c5bb34f226
PFW-1362 Show if SpoolJoin is enabled or disabled at bootup
2022-09-16 10:23:47 +02:00
fb27a7d72b
PFW-1362 Remove "NA" EEPROM status
2022-09-16 10:23:47 +02:00
166ecbc7d8
PFW-1362 Fsensor is not required for Spooljoin
...
Since the Fsensor is not required to use SpoolJoin,
it makes little sense to me that we need the fsensor
to "enable" SpoolJoin
2022-09-16 10:23:47 +02:00
d51026d8f7
PFW-1362 Rename settings for consistency
2022-09-16 10:23:47 +02:00
7c95f87867
PFW-1362 Fsensor status is not required for SpoolJoin
2022-09-16 10:23:47 +02:00
715af8fcc2
Rename files to SpoolJoin
2022-09-16 10:23:47 +02:00
Guðni Már Gilbert
3d-gussner
Yuri D'Elia
Yuri D'Elia
Alex Voinea
Panayiotis-git
Jakub Dolezal
D.R.racer
VintagePC
DRracer
Tomáš Jozífek
Tom Mittendorf
Guðni Már Gilbert