0546566fc7
Update stale message
2023-12-04 07:19:58 -05:00
4dfc484265
Merge pull request #4207 from gudnimg/crashdet_cancel-fixup
...
`crashdet_cancel()` doesnt cleanup all variables when USB printing
2023-12-01 17:41:33 +01:00
4d9dc11510
power panic: pause the print, and wait for M79
...
"PRUSA uvlo" is the last g-code to be processed after the power panic
recovery. For host prints, we want to finish processing all these
g-codes and put the print in a paused state.
Currently I am using lcd_pause_print() but this may be simplified
later.
A new PrinterState is introduced PowerPanicWaitingForHost to
differentiate this paused state from the typical paused state.
In this new paused state the printer is waiting for the host to boot up
and send M79.
Once M79 is seen a new action is sent "// action:uvlo_recovery_ready"
It is up to the host software to then resume the print correctly. All
the needed information to resume the print is in EEPROM and can
be read by using the D3 g-code.
Change in memory:
Flash: +82 bytes
SRAM: 0 bytes
2023-12-01 16:16:39 +01:00
02c5da198d
Enable EEPROM_UVLO flag for host prints
...
Change in memory:
Flash: -30 bytes
SRAM: 0 bytes
2023-12-01 16:16:39 +01:00
ce24d917e6
power panic: Only send M24 for SD prints
...
For host prints, we don't want to send M24.
Change in memory:
Flash: +16 bytes
SRAM: 0 bytes
2023-12-01 16:16:39 +01:00
67c7ad1c99
power panic: improve file position recovery
...
- Only queue M26 for SD prints
- Add M110 to set gcode_LastN for host prints
- Remove one debug log to save resource (52 bytes)
Change in memory:
Flash: -14 bytes
SRAM: 0 bytes
2023-12-01 16:16:39 +01:00
665c01804c
power panic: remove redundant lcd_setstatuspgm
...
If recover_print was never called, then there should be
no need to call lcd_setstatuspgm(MSG_WELCOME) since
the status line was not modified by the power panic feature.
Change in memory:
Flash: -4 bytes
SRAM: 0 bytes
2023-12-01 16:16:39 +01:00
e2d0e9a2ee
power panic: remove redundant lcd update calls
...
lcd_show_fullscreen_message_yes_no_and_wait_P will
enable LCD update upon exit.
Change in memory:
Flash: -24 bytes
SRAM: 0 bytes
2023-12-01 16:16:39 +01:00
02a5228f5e
Merge pull request #4520 from 3d-gussner/MK3_Reprint_OP
...
Change Reprint action message to comply with OctoPrint actions
2023-12-01 09:06:32 +01:00
096a1c9fe0
Change Reprint action message to comply to OctoPrint actions
2023-11-30 15:08:48 +01:00
b37e39fdd9
Merge pull request #4427 from gudnimg/minor-stepper-opt
...
optimisation: stepper: make `dda_isteps_t` an array
2023-11-29 08:54:38 +01:00
3216ef863a
Merge pull request #4149 from gudnimg/tone-opt
...
use `uint16_t` instead of `uint32_t` when writing to OCR4C register
2023-11-29 08:26:54 +01:00
ff42510a5c
Merge pull request #4512 from jamesdehart/fix-spelling-temperature
...
Fix Spelling: temperature.cpp
@jamesdehart Thanks for the PR even a small community PR like this is very appreciated 🤗
2023-11-28 08:54:15 +01:00
ba004d2fa8
Merge pull request #4514 from DRracer/current-tool
...
MMU2: Report current tool onto the serial
2023-11-27 17:13:49 +01:00
67d7be2b2d
MMU2: Report current tool onto the serial
...
PFW-1546
2023-11-27 13:16:13 +01:00
0462b7289a
MMU2: enlarge the Idler's SG_thrs range in Tune menu
...
Based on experience of mibehaving MMU2S units, a broader range seems to help more people in getting their unit to home properly.
Related to issue #4285
2023-11-27 08:57:28 +01:00
e2a60be029
Fix Spelling: temperature.cpp
...
While running the temperature calibration. I happen to notice the `estimate` was spelled `estimat`.
2023-11-25 15:28:18 -07:00
9f9bb12eeb
Merge pull request #4419 from gudnimg/reduce-stack-m600-opt
...
M600: reduce stack usage
2023-11-24 05:39:26 +01:00
7749cdec20
Merge pull request #4510 from 3d-gussner/MK3_Reprint
...
PFW-1536: Reprint function implemented for MK3S/MK3S+
2023-11-24 05:37:48 +01:00
d9d42a0678
Use of PrinterState for Reprint menu
2023-11-23 06:47:04 +01:00
e1e0b0afa1
Refactor code which resets crash detection setting
...
Add function crashdet_use_eeprom_setting
Change in memory:
Flash: -52 bytes
SRAM: 0 bytes
2023-11-22 21:19:43 +00:00
30d0da4698
Close SD file in print_stop instead of UnconditionalStop()
...
Change in memory:
Flash: -6 bytes
SRAM: 0 bytes
2023-11-22 21:19:17 +00:00
3ad40f0206
crashdet_cancel doesnt cleanup all variables when using Octoprint
...
I would think that this should behave similarly as when stopping
the print via the LCD.
Changed UnconditionalSto()p to not close the SD card file
if we're using Octoprint. Then there shouldnt be any file open.
Some of the variables which were not reset:
isPrintPaused
pause_time
saved_start_position
saved_printing_type
Bed heater may be left on?
Change in memory:
Flash: -28 bytes
SRAM: 0 bytes
2023-11-22 21:19:17 +00:00
0b4af3b97f
Fix: Reprint menu does not appear during the heating
2023-11-22 12:20:13 +01:00
73436e9351
Fixed Reprint from USB and from SD, some debug is needed
2023-11-22 12:20:00 +01:00
ec1c215681
Updates to translations of "Reprint" to Slovak and Romanian languages
2023-11-22 12:19:10 +01:00
7130504fcf
Apply the reprint_pr_changes_diff2.txt provided by @3d-gussner
2023-11-22 12:18:59 +01:00
f48c9e0d4f
Fix execution of update-po.py
2023-11-22 12:18:45 +01:00
242fdc863b
Execution of lang/update-pot.py and lang/update-po.py
2023-11-22 12:16:38 +01:00
ce135a0976
Added support for reprint and streamed GCODE
2023-11-22 12:14:08 +01:00
532a5b3e2f
- Serial message --> /// action:reprint done
...
- Yes/no question --> Need to fix the bug related with the filename print --> if (lcd_show_fullscreen_message_yes_no_and_wait_P(altfilename, false, LCD_LEFT_BUTTON_CHOICE)==LCD_LEFT_BUTTON_CHOICE)
2023-11-22 12:14:00 +01:00
004169034a
Remove some MYSERIAL calls
2023-11-22 12:13:24 +01:00
ae5fbce6e7
Remove MYSERIAL.println code (debug purpose) and old commented code
2023-11-22 12:13:16 +01:00
a52d5430aa
Change to enquecommandf_P and enquecommand_P
2023-11-22 12:13:01 +01:00
7a6cfda34f
Fix SV translation length of MSG_REPRINT
2023-11-22 12:12:50 +01:00
cb92fd5002
Fix the length of the PL translation of MSG_REPRINT
2023-11-22 12:12:21 +01:00
e8a2d4c7e1
Reprint function integrated on 3.13v
2023-11-22 12:11:39 +01:00
8615a8dad5
Merge pull request #4429 from 3d-gussner/MK3_PFW-1525_Printer_Ready
...
PFW-1525 Add `Set Ready`menu
2023-11-22 08:52:39 +01:00
02459edcb6
Rebase fix
...
Add documentation
Whitespace
2023-11-22 08:21:52 +01:00
d394645b69
Whitespace
2023-11-22 07:59:18 +01:00
af79ac0714
Add `SetPrinterState(PrinterState::Idle);` after `lcd_commands_type = LcdCommands::Idle;`
2023-11-22 07:58:17 +01:00
d5d77ee243
Cleanup documentation
2023-11-22 07:58:17 +01:00
880d2f28bd
LCD menu only sends `// action:ready` or `// action:not_ready` via serial
...
Host has to send back state with `M72 S1|0` to keep printer and host in sync
Changed LCD menu messages to `Set ready` and `Set not ready`
Updated translations
2023-11-22 07:58:17 +01:00
516ae1b952
Update state
2023-11-22 07:58:17 +01:00
dfcaa330fa
Fix cmake build
2023-11-22 07:58:17 +01:00
d3b98f30a7
Show Set Ready LCD menu only when M79 timer is running.
2023-11-22 07:58:17 +01:00
514607318e
Add printer_state.cpp/.h
2023-11-22 07:58:17 +01:00
d276695ce7
Set Ready
2023-11-22 07:58:13 +01:00
bbae8dd956
Merge pull request #4493 from gudnimg/print-job-timer-marlin
...
PFW-1206: Implement Marlin's print job timer and add M75-M78
2023-11-22 07:44:09 +01:00
134e892d8e
Fix build failure
...
Another isPrintPaused was added by rebase
2023-11-21 18:40:28 +00:00
vintagepc
3d-gussner
gudnimg
D.R.racer
James DeHart
Juan Francisco Estrada