733bc874fb
Move G28W0 to messages
...
No change in memory
2023-03-18 16:48:30 +00:00
466a6a8fc3
Add M600 into PROGMEM
...
Change in memory:
Flash: -10 bytes
SRAM: 0 bytes
2023-03-18 16:33:13 +00:00
129cc18cbf
Add M23 %s into PROGMEM
...
Change in memory:
Flash: -14 bytes
SRAM: 0 bytes
2023-03-18 16:18:05 +00:00
7c0ead7bc2
Add M24 into PROGMEM
...
Change in memory:
Flash: -8 bytes
SRAM: 0 bytes
2023-03-18 16:15:10 +00:00
5f8fc64a32
Restore previous Z-lift in M701/M702
...
Previously when the firmware called M701/M702 manually
there was no Z lift. But after we added support for the Z
parameter we set the default to 50mm.
Change strings "M701" to "M701 Z0" and "M702" to "M702 Z0"
to restore the previous behavior from before 3.13.
Also pulled the gcodes into PROGMEM in message.cpp
along with M83 and M84 to save memory.
Change in memory:
Flash: -34 bytes
SRAM: 0 bytes
2023-03-18 15:34:47 +00:00
942021cb2b
PFW-1503 Fix an issue where the menu is dismissed in First layer calibraiton
...
When the extruder lifts up after completing the Purge line,
the baby stepping is not allowed for a short time. This dismisses
the menu. We don't want this behavior, so only apply the Z-axis requirement
when printing.
Change in memory:
Flash: +8 bytes
SRAM: 0 bytes
2023-03-18 12:47:40 +00:00
e40d8ebbcc
Implement printJobOngoing()
...
This makes the if statments a little bit more readable
Change in memory:
Flash: -88 bytes
SRAM: 0 bytes
2023-03-18 12:18:43 +00:00
561d8599d2
PFW-1503 drop {} for consistency
2023-03-18 11:56:06 +00:00
59314a41c1
PFW-1503 only allow babystepping on the first couple of layers
...
Change in memory:
Flash: +28 bytes
SRAM: 0 bytes
2023-03-18 11:56:06 +00:00
09d918ce5d
PFW-1503 Change BABYSTEP_ALLOWED to babystep_allowed
...
I initially started with a preprocessor macro
called BABYSTEP_ALLOWED, but now it is a function.
It more common to use lower case for function names
2023-03-18 11:56:06 +00:00
bb614f669d
PFW-1503 Add additional check
...
Add lcd_commands_type == LcdCommands::Layer1Cal
just in case blocks_queued() is 0 for one instant between
lcd_command steps
Change in memory:
Flash: +8 bytes
SRAM: 0 bytes
2023-03-18 11:56:06 +00:00
bc2366cd8d
PFW-1503 Improve live Z babystep menu handling
...
Fixes an issue with running first layer calibration twice in a row.
Improvements:
Now the Z baby step menu closes automatically when first layer calibration is done.
No need to wait for a timeout or close the menu manually by setting a variable
If the baby stepping menu is open, and suddenly
the printer enters a state where baby stepping
is not allowed.
The printer will save the last value before closing the menu.
When LcdCommands != Idle, don't dismiss
the Z baby step menu. This saves 20B
Change in memory:
Flash: -130 bytes
SRAM: 0 bytes
2023-03-18 11:56:05 +00:00
5c010a3aaa
PFW-1509 Fix an issue with unload when nozzle is cold
...
Change in memory:
Flash: -2 bytes
SRAM: 0 bytes
2023-03-18 10:43:23 +00:00
c3235386a1
Bump up commit number
2023-03-15 07:52:01 +01:00
8b49d241d2
revert BTN_MORE non-translated
2023-03-15 07:03:41 +01:00
00309f42c3
Bump up fw version
...
6508 from t3.13.0-BETA1
+50 commits
+1 for this commit
+1 for merge
2023-03-14 15:18:13 +01:00
3fe2f25c9f
Disable reading MMU register 0x21
...
It has proven to be too unreliable and may confuse end users.
2023-03-14 15:12:50 +01:00
68b4a8a6cb
Last minute changes need a revert of the fw bump up
2023-03-14 11:22:43 +01:00
e87e1630e2
Bump up version
...
t3.13.0-BETA1 commit nr 6508
+46 commits between
+1 commit for this PR
+1 commit for the merge
=6556
2023-03-14 09:09:38 +01:00
e951a106d6
Messages fit to pages
2023-03-14 08:56:46 +01:00
8604c93ccc
Shorten messages as users will contact support anyway
2023-03-14 08:32:16 +01:00
616cf61583
Revert
2023-03-14 08:31:21 +01:00
22e70faa71
Remove `MMU2` and `MMU unit` messages
...
Saves 26byte of flash
Saves -368 byte in trasnlations
2023-03-14 08:30:15 +01:00
7676df88a4
Rename forgotten `MMU2` message to `MMU`
2023-03-14 08:30:03 +01:00
235c4ae943
Do not `MSG_BTN_MORE` translate
2023-03-14 08:26:39 +01:00
9721a87ef2
Raname `MMU2` message to `MMU` as everywhere
2023-03-14 08:24:50 +01:00
03778226ca
Remove `Select Extruder:` message
...
Post fix PR4064 for update.po*.py scripts
2023-03-14 08:24:12 +01:00
93598ef00d
Change some messages to be max three rows instead of two
...
Yes|No are now located at the 4th row and so messages can
use three rows. This should allow improvement in some translations.
2023-03-14 08:23:40 +01:00
ebf94c572f
PFW-1504 Minor optimisation
...
Change in memory:
Flash: -4 bytes
SRAM: 0 bytes
2023-03-13 06:47:08 +01:00
42878341af
PFW-1504 More correct solution to the pixel count issue
...
The fact that the relationship between
machine position and pixel index is not linear
means we cannot simply rely on comparing
the previous position to the next machine position. i.e derivative of E_AXIS
Because around the max amplitude of the triangle wave
the slope will suddenly change sign and will create a deadzone
which has width 2*mm_per_pixel.
For MMU2S this is ~10mm (or two pixels).
Instead we should split the moves.
And only plan the 2nd move once we're
at the top of the triangle wave. That way we don't really care about the position delta.
Now we just calculate the current y(x)
position relative to current position and divide by mm_per_pixel.
If there is a delta measured with unit 'pixel' then that means
its time to render the next pixel.
This solution seems to work well so far on my end.
Change in memory:
Flash: +2 bytes
SRAM: 0 bytes
2023-03-13 06:47:08 +01:00
b5e323e67c
PFW-1504 rename length_step_mm to mm_per_pixel
...
Its more descriptive
2023-03-13 06:47:08 +01:00
9865d4a38a
PFW-1504 Add precision error
...
This fixes an issue where sometimes
not all 20 pixels are rendered.
It is better to render 1 too many pixels (sometimes), rather than rendering too few.
Change in memory:
Flash: +18 bytes
SRAM: 0 bytes
2023-03-13 06:47:08 +01:00
f2157c6f1d
Fixup
...
We're always setting the cursor position when rendering now
Saves 8 bytes of flash
2023-03-13 06:47:08 +01:00
c518bfdb73
PFW-1504 Set cursor position each time to be safe
...
Change in memory:
Flash: +18 bytes
SRAM: 0 bytes
2023-03-13 06:47:08 +01:00
59e1ac0396
PFW-1504 implement stepper_get_machine_position_E_mm()
...
This function should be used when reading the current machine
position while a move is ongoing
No change in memory
2023-03-13 06:47:08 +01:00
690d83a94a
fixup
2023-03-13 06:47:08 +01:00
9145c8f59f
PFW-1504 too much?
...
I'm not happy with the current solution, I think we can improve it
by using the fact that this is a triangle wave. Need to think about it.
2023-03-13 06:47:08 +01:00
73c76579af
PFW-1504 Add init for progress bar
...
In case we are running a retry, the firmware
should clear the old rendering before
starting on a new one
Change in memory:
Flash: +6 bytes
SRAM: 0 bytes
2023-03-13 06:47:08 +01:00
51f1aa14a5
PFW-1504 Update last position as quickly as possible
...
0.1mm extrusion may happen while updating the LCD
No change in memory
2023-03-13 06:47:08 +01:00
bbfc4b9f78
PFW-1504 initial commit
...
Change in memory:
Flash: +162 bytes
SRAM: 0 bytes
2023-03-13 06:47:08 +01:00
04d440a9c8
Fix AutoLoad filament menu not shown when FSensor is [Off] ( #4072 )
...
Fix AutoLoad filament menu not shown when FSensor if [Off]
2023-03-10 14:23:56 +01:00
ba41b2bb0b
Fix M706 lcd message stuck
2023-03-09 07:00:40 +01:00
e787111922
Add MMU error code: MCU_UNDERVOLTAGE_VCC ( #4069 )
...
+ read bandgap voltage periodically
+ correct wording of ERR_ELECTRICAL_MCU_UNDERVOLTAGE_VCC (as requested in Prusa-Error-Codes PR#81)
2023-03-08 15:42:25 +01:00
a20a7232a8
Change "Extruder N" to "Filament N"
...
Change in memory:
Flash: -52 bytes
SRAM: 0 bytes
2023-03-06 10:26:12 +01:00
0b261ad4de
remove duplicate function in planner
...
moves_planned() should be used instead
No change in memory
2023-03-03 21:11:16 +00:00
03280c48d5
Merge pull request #4059 from gudnimg/planner-opt-subtraction
...
planner: calculate step difference once
2023-03-03 14:42:47 +01:00
474d489c39
Merge pull request #4033 from gudnimg/improve-preheat-target
...
preheat: improve target temperature threshold
2023-03-03 14:41:58 +01:00
bc818636b0
Increase MMU FW version to 2.1.8
...
in relation to MMU-218
2023-03-02 19:58:00 +01:00
d487254806
planner: calculate step difference once
...
Change in memory:
Flash:-158 bytes
SRAM: 0 bytes
2023-03-01 22:28:08 +00:00
051054b0db
Bump up FW version and build number
2023-02-24 16:42:36 +01:00
303a67cd6f
Introduce MMU EEPROM reset feature
...
This new feature requires MMU FW v 2.1.7 (which brings some more small changes)
2023-02-24 15:26:07 +01:00
31bfbb4ed0
Merge pull request #4023 from DRracer/rename-eject-mmu
...
PFW-1497 Change Eject filament -> Eject from MMU
2023-02-23 10:48:35 +01:00
afc866e756
Merge pull request #4010 from gudnimg/improve-backlight-control
...
backlight: always allow backlight to dim/wake
2023-02-21 10:00:03 +01:00
8a926fad10
backlight: set rotation flag when certain amount of pulses are detected
...
We don't want to trigger a backlight wakeup randomly, for example
due to background noise.
2023-02-20 18:26:43 +00:00
36c6b323c4
Set `Is filament loaded? Yes|No` default to `No` without a timeout.
2023-02-20 16:31:23 +01:00
791b9b4d39
Merge pull request #4028 from DRracer/pr3322-updated
...
Merge duplicate strings in cmdqueue.cpp
2023-02-20 13:51:09 +01:00
496b52b819
preheat: sync temperature threshold in M600 and Wizard
...
* M600 used 1°C threshold, which may increase the waiting time a bit
* Wizard used 3°C
Sync both to use TEMP_HYSTERESIS for consistancy
No change in memory footprint
2023-02-19 13:23:31 +00:00
6ad126ef0b
optimisation: preheat menu always uses integers for target temperature
...
Let's drop the float comparison since it not needed
Change in memory:
Flash : -16 bytes
SRAM: 0 bytes
2023-02-19 13:21:30 +00:00
319fec47f0
preheat: improve target temperature threshold
...
Use 5°C threshold to be consistant with other parts
of the firmware.
Relying on 95% of the target temperature creates
a dependency on the temperature:
PLA: Target = 215°C, threshold = 10.75°C
PETG: Target = 230°C, threshold = 11.5°C
ABS: Target = 255°C, threshold = 12.75°C
ASA: Target =260°C, threshold = 13.0°C
PC: Target = 275°C, threshold = 13.75°C
My proposal is we instead use a constant
TEMP_HYSTERESIS = 5, which is consistent with
M109, and behavior when restoring print from RAM
and some of the MMU code (like unload function)
Change in memory:
Flash: +2 bytes
SRAM: 0 bytes
2023-02-19 12:59:58 +00:00
db878c9996
backlight: always allow backlight to dim/wake
...
This commit adds the ability for the firmware to dim and wake the
backlight when LCD updates are disabled. Such as in the MMU error screen
or when rendering full screen messages which typically
disable the LCD updates to prevent the status screen from rendering.
Fixes #2777
Change in memory:
Flash: -26 bytes
SRAM: +1 byte
2023-02-18 17:08:35 +00:00
5cd60636f9
Add missing translations + shorten to 16 chars
2023-02-18 17:39:30 +01:00
98e7c15928
Change Eject filament -> Eject from MMU
...
PFW-1497
2023-02-18 17:39:30 +01:00
05662a5c0a
optimsation: reduce code size in LCD rendering
...
Change in memory (MK3S+ Multilang):
Flash: -62 bytes
SRAM: -6 bytes
2023-02-18 16:32:08 +01:00
074057c110
Fix an issue where LCD freezes during loading test
...
It may be useful to view the Sensors menu
while the toolchange loading test is taking
place. For example to see if the reading is flickering
The firmware needs to call lcd_update(0) to update the screen rendering.
Change in memory:
Flash: -2 bytes
SRAM: 0 bytes
2023-02-18 13:16:40 +01:00
555e766296
optimisation: only update mm when i > 0
...
Change in memory:
Flash: -24 bytes
SRAM: 0 bytes
2023-02-18 12:39:44 +01:00
e41b6d106d
optimisation: use more string from PROGMEM
...
Change in memory:
Flash: -10 bytes
SRAM: 0 bytes
2023-02-18 12:39:44 +01:00
9f4a7adb9a
optimisation: extract common M861 code
...
Change in memory:
Flash: -128 bytes
SRAM: 0 bytes
2023-02-18 12:39:44 +01:00
ee23d6c62a
Merge duplicate strings in cmdqueue.cpp
...
Original idea from @GilesBathgate, PR #3322 . This is just a rework on top of current MK3 branch.
2023-02-18 11:37:48 +01:00
3381bf2f7e
Merge pull request #2201 from vintagepc/2091_2153_sheet_Mcode
...
Add M850 code for setting sheet label and offsets
2023-02-17 15:12:22 +01:00
1b3fa8bfe9
TM: Move headers to support the legacy build system
2023-02-17 15:01:59 +01:00
a8f219259a
TM: Split default model parameters into a separate header
...
Preparation to support multiple default model parameter sets
2023-02-17 15:01:59 +01:00
d1ff728e4f
TM: future-proofing for incompatible model upgrades
...
Introduce a model version. This is initialized at "1" and doesn't
require any upgrade/downgrade checks since it's currently
retro-compatible.
2023-02-17 15:01:59 +01:00
9bd03cedb9
TM: Fix UV identity
2023-02-17 15:01:59 +01:00
ddf5147f9f
TM: Optimize temp_model_set_lag
...
Save about 20 bytes by rewriting the sample count check
2023-02-17 15:01:59 +01:00
b676d395e3
TM: Handle L/TEMP_MODEL_LAG
2023-02-17 15:01:59 +01:00
0bf6a5bc4b
TM: Handle UV (PTC loss)
...
Model UV as power-invariant, so that scaling P doesn't change the
intercept location (that is, the zero point remains at the same
temperature even for more powerful heaters).
NOTE: It's not clear to me whether this is generally true (couldn't
find a datasheet from the same heater in diffent power variants
showing the efficiency loss)
2023-02-17 15:01:59 +01:00
ba96c8d457
TM: Handle D/TEMP_MODEL_fS
2023-02-17 15:01:59 +01:00
eb88b720ac
TM: Handle UVDL set/load/report/upgrade
...
- Expose TEMP_MODEL_fS and TEMP_MODEL_LAG as D and L respectively,
initializing the default values based on the previous hard-coded
values.
- Always round L to the effective sample lag to future-proof model
upgrades or changes (the stored value _is_ the effective value).
- Introduce UV as a new linear term for PTC heaters, defaulting
to an identity for model backward-compatibility.
2023-02-17 15:01:59 +01:00
38b1e64687
TM: Allocate new eeprom parameters for PTC handling
2023-02-17 15:01:59 +01:00
235ce62cd3
Update Marlin_main.cpp
...
Remove more stale code
2023-02-17 08:58:17 -05:00
032d5ebe5b
Update Marlin_main.cpp
...
Fix use of removed function
2023-02-17 08:31:27 -05:00
d0e0b51497
Optimisation: lcd_commands "M702 C" should be "M702"
...
Change in memory:
Flash: -2 bytes
SRAM: 0 bytes
2023-02-17 14:30:20 +01:00
952b1af60b
Consistent use of noinline attribute
2023-02-17 14:30:20 +01:00
754b2d03c3
Remove extraneous line added during merge conflict resolution
2023-02-17 14:30:20 +01:00
25f9728e09
Add noinline attribute to count_e
2023-02-17 14:30:20 +01:00
620b19bbab
Roll up lay1cal_square loops
2023-02-17 14:30:20 +01:00
f92d2279d5
Re-use duplicated strings
2023-02-17 14:30:20 +01:00
8129a14f19
Move layer calibration finish commands into first_layer_cal.cpp
2023-02-17 14:30:20 +01:00
39160bc4ae
Free up some progmem
2023-02-17 14:30:20 +01:00
568eec5ee0
Implement first layer cal with calculated extrusion widths
2023-02-17 14:30:20 +01:00
20eef890a6
Merge branch 'MK3' into 2091_2153_sheet_Mcode
2023-02-17 08:24:49 -05:00
9b64d122dc
Disable MMU2S by default
...
On printers without the MMU no error screen should occur and no attempts of communication with the MMU should be performed -> EEPROM_MMU_ENABLED should default to 0.
PFW-1418
2023-02-17 12:53:07 +01:00
6745b2c766
Shorten Reset MMU button to fit LCD
...
Button strings are limited to 8 characters
2023-02-13 07:08:54 +01:00
b63f5433df
Don't show Pause/Stop menus while processing T-codes
...
PFW-1449
Change in memory:
Flash: +18 bytes
SRAM: +1 bytes
2023-02-12 15:58:07 +01:00
504099bd6c
optimisation: reduce code size in rendering cursor
...
Change in memory:
Flash: -62 bytes
SRAM: 0 bytes
2023-02-11 19:06:14 +01:00
c51aa10087
optimisation: spooljoin: use new eeprom init method
...
Change in memory:
Flash: -40 bytes
SRAM: -1 byte
2023-02-11 15:58:07 +01:00
982b1bb4bd
optimisation: backlight: use new eeprom_init function
...
Change in memory:
Flash: -56 bytes
SRAM: 0 bytes
2023-02-11 15:56:46 +01:00
c2a952cee5
optimisation: sound: use new eeprom_init function
...
Change in memory:
Flash: -18 bytes
SRAM: 0 bytes
2023-02-11 15:56:46 +01:00
8794ab2f71
respect Once sound mode
...
Change in memory:
Flash: +4 bytes
SRAM: 0 bytes
2023-02-11 15:54:33 +01:00
96fc90c80b
Revert a change in the MMU error screen logic
...
We can pull this code into a common function in a separate PR
2023-02-11 15:54:33 +01:00
5b4bc8bcdb
Tune louder beeps to match previous M600 behavior
2023-02-11 15:54:33 +01:00
b4f9f6d0b5
fixup: make sure to start the timer
...
Change in memory:
Flash: +10 bytes
SRAM: 0 bytes
2023-02-11 15:54:33 +01:00
8db2fbc97f
Improve sound handling for MMU error screen
...
Change in memory:
Flash: -174 bytes
SRAM: +4 bytes
2023-02-11 15:54:33 +01:00
e34faee389
optimisation: don't inline Sound_MakeCustom
...
Change in memory:
Flash: -32 bytes
SRAM: 0 bytes
2023-02-11 12:42:47 +01:00
7799853a05
optimisation: remove duplicate code
...
Sound_MakeCustom should play the sound
if critical = true OR the sound is not Silent
Change in memory:
Flash: -16 bytes
SRAM: 0 bytes
2023-02-11 12:42:47 +01:00
c826ae989f
Remove Done button on FINDA-related MMU error screens
...
Follows the requirements from Prusa-Error-Codes yaml definition.
Saves a fwe bytes as well as the button switch() statement got simplified.
PFW-1494
2023-02-10 14:38:18 +01:00
8b1b632164
Fix copy/paste typo thanks to @gudnimg
2023-02-10 14:35:36 +01:00
4f8dbb19fd
Fix `M862.x` LCD messages
...
As the new menue adds a Yes/No option the messages
need to be limited to c=20 r=3
Updated/shortened all translations
2023-02-10 14:35:36 +01:00
b02e8d9961
Fix First layer cal being stored without confirming with knob
2023-02-10 14:34:16 +01:00
c3cfc86094
Fix #3977
2023-02-10 14:27:04 +01:00
d403d58b19
TM: Do not emit an "error:" on the serial for recoverable errors
...
Use "echo:" for thermal model error reporting to avoid octoprint
automatically sending a M112 kill.
Keep using "error:" instead for other thermal errors (MAXTEMP/etc).
This should allow resuming a thermal mode pause with the default
octoprint settings.
2023-02-10 14:24:50 +01:00
ea7e717204
Cleanup: Remove various dead code
2023-02-10 08:17:36 +01:00
ca978080c4
Change to Thermal model
...
Add prusa.io/tm-cal link
and update all TM related translations
2023-02-08 15:36:59 +01:00
26126906ef
Hardcode expected MMU FW version into the error message v2
...
This is an 80% solution to PFW-1488 which should be somewhat compatible with the existing languages/translations infrastructure.
I don't see a point in extending the infrastructure a great deal to support some compile-time replacement in order to patch just MSG_DESC_FW_UPDATE_NEEDED.
Related PR: https://github.com/prusa3d/Prusa-Firmware/pull/3993
2023-02-08 10:50:33 +01:00
99761bdff7
optimisation: re-use adjust_bed_reset()
...
Move the code into eeprom.cpp since we're only working with EEPROM
Change in memory:
Flash: -42 bytes
SRAM: 0 bytes
2023-02-08 08:01:55 +01:00
3ddc2cf86d
Add ResetMMU and DisableMMU buttons to specific error screens
...
- MMU not responding/Communication error: add DisableMMU
- MMU FW update needed: add ResetMMU
Flash: +8B
RAM: +0B
2023-02-08 06:48:11 +01:00
296b0414af
Optimize execute_extruder_sequence
...
Save 64B by refactoring of execute_extruder_sequence.
2023-02-08 06:47:50 +01:00
e34ed479ef
PFW-831 Add single buzzer beep when an MMU error screen is shown for the first time
...
If the user has the sound settings set to 'Silent' then this beep should be silent
Change in memory:
Flash: +4 bytes
SRAM: 0 bytes
2023-02-06 08:35:08 +01:00
b28aa6f42a
PFW-1471 Rename 'Toolchange count' to 'Material changes'
...
Added the string to our message so it can be translated
Change in memory:
Flash: -10 bytes
SRAM: 0 bytes
2023-02-06 08:33:40 +01:00
ba34661b62
Fixup after rebase onto MK3
2023-02-01 08:28:23 +01:00
d66e2b66c2
Cleanup: use setTargetHotend consistently for one extruder
...
Main changes:
* setAllTargetHotends() is removed
* setTargetHotendSafe() is removed
* Extruder parameter on setTargetHotend() is dropped
Change in memory:
Flash: -192 bytes
SRAM: 0 bytes
2023-02-01 08:28:23 +01:00
ed80defc2c
Shorten the Try-Load-Unload sequence
...
... and allow easier future tweking in case of need
Also, save ~30B of code by returning the previous E-motor position.
2023-02-01 06:38:19 +01:00
e597be2cb5
PFW-1381 Optimise initialisation
...
Change in memory:
Flash: -2 bytes
SRAM: -1 byte
2023-01-31 10:02:15 +01:00
a35e7d543f
Fix bug with button choice on MMU error screen isn't reset
...
PFW-1381
2023-01-31 10:02:15 +01:00
d2f3835b2c
Fixup after review
2023-01-31 09:35:22 +01:00
8720602b0e
Fix an issue with corrupt serial messages
2023-01-31 09:35:22 +01:00
43ae2c78e5
Fix cmake build
2023-01-31 09:35:22 +01:00
528abcb8d8
clang-format
2023-01-31 09:35:22 +01:00
0555376502
Refactor mmu2.cpp and related interfaces
...
The general idea is to keep platform specific implementation away from the MMU state machines as much as we can.
That would enable unit testing the top level MMU state machine and integration into other project as well (if needed).
2023-01-31 09:35:22 +01:00
e39f2d132e
TM: Check for PC parameters more carefully
2023-01-27 14:57:59 +01:00
216b935488
Minor typo
2023-01-26 12:20:43 +01:00
05cd50e2ef
Update M214 description with link to RepRap wiki
2023-01-26 12:20:43 +01:00
da63d73585
optimisation: don't print floats with lcd_print()
...
Change in memory:
Flash: -442 bytes
SRAM: 0 bytes
2023-01-25 18:21:22 +00:00
a5f7f1d735
optimisation: change index from uint32_t to uint8_t
...
Change in memory:
Flash: -152 bytes
SRAM: 0 bytes
2023-01-25 18:21:22 +00:00
8c4cd11ae0
Cleanup: remove code_value_float()
...
The function adds a bit of overhead compared to code_value()
I suspect this function is a relic of the past.
Change in memory:
Flash: -82 bytes
SRAM: 0 bytes
2023-01-25 16:51:10 +00:00
17e6f1b75e
optimisation: remove conv2str.cpp
...
Change in memory:
Flash: -288 bytes
SRAM: -8 bytes
2023-01-25 06:28:00 +00:00
79a10868fe
cleanup: FILWIDTH_PIN doesn't exist
...
raw_filwidth_value variable is never used
2023-01-24 19:41:45 +00:00
7b163cf464
Merge pull request #3936 from wavexx/tm_cal_htemp
...
TM: Do not restrict autotune temperature
2023-01-24 14:20:55 +01:00
fab4165f4a
Merge pull request #3920 from wavexx/selftest_ok_alert
...
wizard: Do no set "Self test OK" as an alert message
2023-01-24 14:16:44 +01:00
1f54dfd0b2
Merge pull request #3941 from wavexx/tm_wizard_nowarn
...
wizard: Disable TM warnings during calibration
2023-01-24 14:15:04 +01:00
53fb4c3e3f
Move altfan eeprom initialization to extruder_altfan_detect()
...
flash: -16B
RAM: 0B
2023-01-23 19:47:03 +00:00
7245c76094
Fix an issue where Altfan Override setting in EEPROM is not respected at boot-up
2023-01-23 19:47:03 +00:00
c9f3a4cfce
wizard: Disable TM warnings during calibration
...
During calibration model warnings are possible/normal. This is
apparently leading some into thinking the hotend might be faulty
and abort the calibration with a hard reset.
Disable warnings/beeps during calibration.
Rely on the error threshold only.
2023-01-23 16:52:27 +01:00
679208b29e
TM: Do not restrict autotune temperature
...
Fix a wrong type that prevents running TM autotune at temps >127
2023-01-20 19:18:19 +01:00
39f9979655
optimisation: Combine if statement in M600
...
Change in memory:
Flash: -52 bytes
SRAM: 0 bytes
2023-01-18 09:44:27 +01:00
6298722f9a
Disable E-motor before the MMU starts doing something
...
It may seem counterintuitive to disable the E-motor, but it gets enabled in the planner whenever the E-motor is to move.
The idea behind disbling the E-motor when it won't be needed for some time is to save power and lower the heat of the motor.
Therefore it is especially important to disable the motor before the printer pauses a print due to some MMU error screen.
2023-01-18 09:42:57 +01:00
0c352ac2d1
Disable M47 if TMC2130 drivers are used
...
flash: -126B
RAM: 0B
2023-01-17 20:37:27 +01:00
d83c0f6c40
Fix an issue with indexing PROGMEM pointer
...
Using array index 'pointer[index]' doesn't work properly.
Instead using "pointer + index" works fine.
No change in memory footprint
2023-01-16 12:36:57 +01:00
9416310f7e
optimisation: move row_offsets into PROGMEM
...
Change in memory:
Flash: -42 bytes
SRAM: -4 bytes
2023-01-16 12:36:57 +01:00
eeb5f3d50c
optimisation: refactor menu_draw_P()
...
Add a way to only change the LCD column
Change in memory:
Flash: -90 bytes
SRAM: 0 bytes
2023-01-16 12:36:57 +01:00
Guðni Már Gilbert
3d-gussner
D.R.racer
DRracer
Yuri D'Elia
vintagepc
Giles Bathgate
RoboMagus
Alex Voinea